GB/T 3780.1-2015 PDF EnglishUS$140.00 · In stock · Download in 9 seconds
GB/T 3780.1-2015: Carbon black -- Part 1: Test method for iodine adsorption number Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 3780.1: Historical versions
Similar standardsGB/T 3780.1-2015: Carbon black -- Part 1: Test method for iodine adsorption number---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3780.1-2015GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.040.20 G 49 Replacing GB/T 3780.1-2006 Carbon black – Part 1. Test method for iodine absorption number Issued on: MAY 15, 2015 Implemented on: OCTOBER 01, 2015 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the PRC. Table of ContentsForeword ... 3 1 Scope ... 7 2 Normative references ... 7 3 Principles ... 8 4 Reagent ... 8 5 Instruments ... 9 6 Sampling ... 9 7 Test conditions ... 10 8 Analysis procedures ... 10 9 Result calculation ... 12 10 Precision ... 13 11 Test report ... 13 Appendix A (Normative) Preparation, calibration and correction of solutions 14 Appendix B (Informative) Determination of potassium iodide content ... 22 Appendix C (Informative) Structural change comparison between this part and ASTM D 1510-11 ... 24ForewordGB/T 3780 “carbon black” is divided into the following parts. - Part 1. Test methods for iodine absorption number; - Part 2. Determination of oil absorption number; - Part 4. Determination of oil absorption number of compressed sample; - Part 5. Determination of specific surface area - CTAB test method; - Part 6. Determination of tinting strength; - Part 7. Determination of pH value; - Part 8. Determination of heating loss; - Part 10. Determination of ash; - Part 12. Inspection of impurity material; - Part 14. Determination of sulfur content; - Part 15. Determination of light transmittance of toluene extract; - Part 17. Indirect determination of particle size Reflectance method; - Part 18. Standard test methods for evaluation in natural rubber (NR); - Part 21. Determination of sieve residue for rubber compounding ingredients - Water washing method This part is part 1 of GB/T 3780. This part is drafted in accordance with the rules given in GB/T 1.1-2009. This part replaces GB/T 3780.1-2006 “Carbon black - Part 1. Test method for iodine absorption number”. As compared with GB/T 3780.1-2006, the main technical changes are as follows. - MODIFY the “carbon black sampling amount” (SEE Table 1; Table 1 of 2006 version); - ADD the “iodine solution, c (1/2 I2) = 0.4730 mol/L, SEE A.1.1 for the preparation” (SEE 4.1); - DELETE the mercury iodide (4.1 of 2006 version); - ADD “Note 1” (SEE 4.2); - ADD “Note 2” (SEE 4.2); - DELETE the “Method B” from the “analysis procedure” in the prevision version (8.3 of 2006 version); - MODIFY the description of the “blank test” in the “analysis procedure” [SEE 8.5c); 8.2.4.1.5 of 2006 version]; - DELETE the calculation equation from the “calculation results” of the “B method” in the previous version (SEE 9.2 of 2006 version); - ADD the “adjustment of sodium thiosulfate standard solution” and the “adjustment of iodine solution concentration” (SEE A.2.1.1.3, A.2.2.1.3); - ADD the “calibration with standard reference carbon black” and the “standard reference carbon black INR iodine absorption number control limit" (SEE A.3, A.4, Table A.1); - DELETE the “SRB6 series standard reference carbon black iodine absorption literature value” (Appendix C of 2006 version); - ADD the “determination of potassium iodide content” (SEE Appendix B). This part is, through the re-drafting method, compiled with reference to ASTM D 1510-11 “Carbon black standard test method - iodine absorption number”. As compared with ASTM D 1510-11, this part has many structural adjustments. In Appendix C, it lists the clause comparison between this part and ASTM D 1510-11. The technical differences between this part and ASTM D 1510-11 AND their causes are as follows. - MAKE reference to the Chinese national standard GB/T 3778, GB/T 3782, GB/T 15338 as corresponding to the D 4483, D 1799, D 1900, D 4821 which are referenced in ASTM D 1510-11; ADD GB/T 8170, GB/T 12805, GB/T 12806, and GB/T 12808, in order to facilitate Chinese standard users (SEE Chapter 2); - DELETE “meaning and application”, which is not preferable to be included into the standard text (SEE Chapter 4 of ASTM D 1510-11); - MODIFY “When replacing equipment or newly purchasing a large amount of iodine or sodium thiosulfate, OR both cases occur, the regression equation shall be redefined” into “When replacing equipment OR using different batches of iodine or sodium thiosulfate OR the sodium thiosulfate solution is stored for 30 d, it shall re-test the standard reference carbon black to confirm the regression equation”, which is more comprehensive and clear (SEE A.3.6; 8.6 of ASTM D 1510-11); - ADD “Laboratory may choose other standard reference carbon blacks with the same effect”, in order to improve operability (SEE A.3.2 note); - ADD “Standard reference carbon black INR iodine absorption number control limit” to facilitate standard users (SEE A.4, Table A.1); - ADD “Structural changes of this part as compared with ASTM D 1510-11” (SEE Appendix C). This part was proposed by the China Petroleum and Chemical Industry Association. This part shall be under the jurisdiction of the Carbon Black Branch of National Rubber and Rubber Products Standardization Committee (SAC/TC 35/SC 5). The drafting organizations of this part. China Rubber Group Carbon Black Industry Research and Design Institute, Ningbo Detai Chemical Co., Ltd., Jinneng Technology Co., Ltd., Qujing Zhongyi Fine Chemical Co., Ltd., Longxing Chemical Co., Ltd., Shandong Lianke New Materials Co., Ltd., Sichuan Institute of Technology. The main drafters of this part. Nie Suqing, Liu Jian, Dai Chuanyin, Ma Weiwei, Feng Jie, Jiang Liangqiang, Hou Hegang, Zhang Youwei, Jin Yongzhong. This Standard replaces the standard previously issued as follows. - GB/T 3780.1-1983, GB/T 3780.1-1991, GB/T 3780.1-1998, GB/T 3780.1-2006; - GB/T 3781.7-1983, GB/T 3781.7-1993. Carbon black – Part 1. Test method for iodine absorption number WARNING. Personnel using this standard shall have practical experience in formal laboratory work. This part does not address all possible safety issues. It is the responsibility of the user to take appropriate safety and health measures and to ensure compliance with the conditions set forth in the relevant national regulations.1 ScopeThis part of GB/T 3780 specifies the method for determining the iodine absorption number of carbon black and acetylene black for rubber. This part applies to all kinds of rubber carbon black (not including S series, mixed gas and natural gas tank carbon black) and acetylene black. It is not suitable for carbon black with surface porosity, volatility and the presence of extract.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this Standard. GB 3778 Carbon black for use in rubber products GB/T 3782 Acetylene black GB/T 8170 Rules for rounding off for numerical values & expression and judgment of limiting values GB/T 12805-2011 Laboratory glassware - Burettes GB/T 12806-2011 Laboratory glassware - One-mark volumetric flasks GB/T 12808-1991 Laboratory glassware - One mark pipettes GB/T 15338 Carbon black - Validation of test method precision and bias 8.5 PIPETTE 20 mL of the clear liquid in a 150 mL iodine flask, and USE sodium thiosulfate standard solution to conduct titration in accordance with the following a) or b). a) Titration with digital burette. • ADJUST the switch to the liquid filling position, so that the burette is filled with sodium thiosulfate standard solution; USE this solution to rinse the inlet and the liquid delivery tube. • ADJUST to the titration position; MAKE the counter back to zero; and USE thin paper to wipe the tube tip clean. • USE the (4 ± 0.5) mL/min sodium thiosulfate standard solution for titration of the clear iodine solution until it changes into light yellow; USE water to rinse the tube tip and bottle wall. ADD 5 drops of starch solution; CONTINUE dropping the sodium thiosulfate standard solution until the blue color is approximately disappeared; USE water to rinse the tube tip and bottle wall again; ADJUST the counter to make its increment of 0.01 mL/s ~ 0.02 mL/s; CONTINUE dropping until the solution just becomes colorless, which is the end point. • RECORD the burette reading, accurate to 0.01 mL. • FOLLOW 8.5 c) to conduct the double sample blank... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 3780.1-2015 be delivered?Answer: The full copy PDF of English version of GB/T 3780.1-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 3780.1-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3780.1-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3780.1-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 3780.1-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3780.1-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 3780.1-2015?A step-by-step guide to download PDF of GB/T 3780.1-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 3780.1-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
