GB/T 3487-2024 PDF EnglishUS$275.00 · In stock · Download in 9 seconds
GB/T 3487-2024: Passenger car rims Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 3487: Historical versions
GB/T 3487-2024: Passenger car rims---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3487-2024GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.160.10 CCS G 41 Replacing GB/T 3487-2015 Passenger car rims (ISO 4000-2.2021, Passenger car tyres and rims -- Part 2.Rims, MOD) Issued on. SEPTEMBER 29, 2024 Implemented on. APRIL 01, 2025 Issued by. State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 5 4 Rim profile size codes... 5 5 5° deep groove rim (5°DC)... 6 Annex A (informative) Comparison on structure numbers between this document and ISO 4000-2.2021... 13ForewordThis document was drafted in accordance with the rules given in GB/T 1.1-2020 "Directives for standardization - Part 1.Rules for the structure and drafting of standardizing documents". This document replaces GB/T 3487-2015 "Rims for passenger car". Compared with GB/T 3487-2015, in addition to structural adjustments and editorial changes, the main technical changes in this document are as follows. - Changed the layout of the diagrams, unifying the right side as the tire installation side (see Figure 1, Figure 2 of this Edition; Figure 1, Figure 2 of Edition 2015); - Modified the provisions of the "Snap-on valve hole" section (see 5.4.2 of this Edition; 5.4.2 of Edition 2015); - Added relevant provisions for "Compression-type valve hole" (see 5.4.3 of this Edition). The modification of this document adopted ISO 4000-2.2021 "Passenger car tyres and rims -- Part 2.Rims". Compared with ISO 4000-2.2021, this document has more structural adjustments. See Annex A for a comparison of the structural number changes between the two documents. The technical differences between this document and ISO 4000-2.2021 and their reasons are as follows. - ISO 3911 (see Chapter 3 of this document) was replaced by the normative reference GB/T 2933 to adapt to China's technical conditions; - The normative reference ISO 9413 (see Chapter 3 of this document; Table 5 in ISO 4000-2.2021) has been deleted, and the relevant content has been deleted; - Added "Rim profile size code" and its illustration (see Chapter 4 of this document) for ease of use; - Deleted rim specifications and marking (see Chapter 4 of ISO 4000-2.2021) as their contents are already specified in the referenced standards; - The footnotes of the snap-on valve hole dimension drawing have been changed (see the footnote of Figure 4 of this document; the footnote of Figure 3 in ISO 4000-2.2021). Figure 4 has been deleted because this provision in ISO 4000- 2.2021 is incorrect; - The illustration of the compression valve hole dimensions has been changed (see Figure 5 of this document; Figure 5 of ISO 4000-2.2021). Dimension d (see Table 5 of ISO 4000-2.2021) has been deleted and is now marked directly in Figure 5. The following editorial changes were made to this document. - To coordinate with the existing standards, the name of the standard is changed to "Passenger car rims"; - A note was added to Figure 5."Due to the different manufacturing processes for machining and punching, the figures shown are general rules." Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. The issuing authority shall not be held responsible for identifying any or all such patent rights. This document was proposed by China Petroleum and Chemical Industry Federation. This document shall be under the jurisdiction of National Technical Committee on Tires and rims of Standardization Administration of China (SAC/TC 19). The drafting organizations of this document. Tianjin Jiurong Industrial Technology Co., Ltd., Shandong Linglong Tire Co., Ltd., CITIC Dicastal Co., Ltd., Triangle Tire Co., Ltd., Xiamen Zhengxin Rubber Industry Co., Ltd., Qingdao Sentury Tire Co., Ltd., Beijing Rubber Industry Research and Design Institute Co., Ltd., Sailun Group Co., Ltd., Shantou Haoda Tire Testing Equipment Co., Ltd., Tai'an Qicheng Wheel Manufacturing Co., Ltd., Qinhuangdao Zhongqin Bohai Wheel Co., Ltd., Shandong Xinghongyuan Tire Co., Ltd., Shaanxi Yanchang Petroleum Group Rubber Co., Ltd., and Dalian Goodyear Tire Co., Ltd Main drafters of this document. Gu Zheng, Wen Xiaolei, Wei Jianfeng, Huang Shaobing, Du Juan, Chen Jianming, Qin Long, Li Shuhuan, Zheng Rui, Zhang Jianjun, Chen Xun, Liu Kang, Zhang Dianjie, Zhu Zuoyong, Du Fan, Yin Qingye, Li Miaomiao, Mou Shouyong, Xu Lihong, Chen He. Versions of standard substituted by this document are. - It was first published in 1983 as GB 3487-1983 "Rim contours for motor vehicles". It was first revised in 1989.It was second revised in 1996.It was third revised in 2005. - The fourth revision in 2015 was divided into two documents, namely GB/T 3487- 2015 "Rims for passenger car" and GB/T 31961-2015 "Rims for truck-bus"; - This is the fifth revision. Passenger car rims1 ScopeThis document specifies the specifications, profiles and dimensions of 5° deep groove rims for passenger car wheels and tyre mating areas. This document applies to rims for passenger car wheels.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.3 Terms and definitionsFor the purposes of this document, the terms and definitions defined in GB/T 2933 apply.4 Rim profile size codesThe rim profile size codes are shown in Figure 1.5 5° deep groove rim (5°DC)The wheel rim models are divided into types B and J. The configuration of the wheel Mounting side The rim profile dimensions and tolerances shall comply with Figure 2 and Table 2. With the exception of the valve hole area, the rim profile shall be rotationally symmetrical.Annex A(informative) Comparison on structure numbers between this document and ISO 4000-2.2021 ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 3487-2024 be delivered?Answer: The full copy PDF of English version of GB/T 3487-2024 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 3487-2024_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3487-2024_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3487-2024 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 3487-2024?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3487-2024 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 3487-2024?A step-by-step guide to download PDF of GB/T 3487-2024_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 3487-2024". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
