GB/T 33374-2016 PDF EnglishUS$110.00 · In stock · Download in 9 seconds
GB/T 33374-2016: Ultraviolet curable coatings -- Determination of volatile content Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 33374-2016: Ultraviolet curable coatings -- Determination of volatile content---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT33374-2016GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 87.040 G 50 Ultraviolet curable coatings - Determination of volatile content ISSUED ON: DECEMBER 30, 2016 IMPLEMENTED ON: JULY 01, 2017 Issued by: General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 4 4 Instruments and apparatuses ... 5 5 Sampling ... 6 6 Test procedures ... 6 7 Calculation and expression of test results ... 8 8 Repeatability ... 9 Ultraviolet curable coatings - Determination of volatile content1 ScopeThis Standard specifies the determination methods of volatile content in ultraviolet curable coatings. This Standard applies to the determination of volatile content in ultraviolet curable coatings. Ultraviolet curable inks, adhesives, electron beam-curable coatings, inks, and adhesives can also refer to this Standard. This Standard does not apply to water-based ultraviolet curable coatings.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies to this document. For undated references, the latest edition (including any amendment) applies to this document. GB/T 3186, Paints, varnishes and raw materials for paints and varnishes - Sampling GB/T 6753.4-1998, Paints and varnishes - Determination of flow time by use of flow cups GB/T 20777, Paints and varnishes - Examination and preparation of samples for testing3 Terms and definitionsThe following terms and definitions are applicable to this document. 3.1 Ultraviolet curing; UV curing The hardening process of coatings exposed to UV radiation. 3.2 Processing volatiles Mass loss of the sample during the curing process, under the specified test conditions (i.e., the conditions that simulate the actual industrial ultraviolet curing process). 3.3 Potential volatiles Mass loss of the UV-cured sample in the process of drying at (110±2) °C for 60 min.4 Instruments and apparatuses4.1 Metal flat-bottom vessel Diameter (75 ± 5) mm, edge height 5 mm or ensuring that the sample does not overflow. Alternatively, it can be a vessel of different diameter, while the sample weight shall vary according to the diameter. Note: The viscous coatings can also be made of aluminum foil of a thickness about 0.1 mm. Cut it into a rectangle of a size about (100±10) mm × (300±10) mm that can be folded in half; lightly squeeze the two folded parts to spread the viscous liquid completely. 4.2 Oven Warning – In order to prevent explosion or fire, samples containing volatile substances shall be handled with care, and shall be implemented in accordance with relevant national regulations. In order to ensure the safety of the test, a forced convection oven shall be selected, which can be maintained within the range of ±2 °C of the specified or agreed temperature, and be equipped with a horizontal shelf. Alternatively, a natural convection oven, which is equipped with perforated metal baffles at 1/3 the height of the working chamber, can be used. 4.3 Desiccator Loaded with a suitable desiccant, such as dry silica gel that has been impregnated with cobalt chloride. 4.4 Balance Accuracy 0.1 mg. 4.5 Syringe Disposable syringe, of capacity 1 mL. 4.6 Ultraviolet curing equipment Ultraviolet curing equipment shall meet the following conditions: -- Spectral range: ≥250 nm, main band wavelength 365 nm; 75 – standard diameter of the vessel, in millimeters (mm). Note 1: When mixing samples, manual stirring can not only ensure that the samples are evenly mixed, but also avoid the generation of air bubbles. Note 2: The surface of the syringe – after taking the sample – shall be wiped clean; the sample shall not be left in the neck of the syringe, which can be solved by pulling up the plug of the syringe. After injecting the sample, do not wipe the tip of the syringe; instead, remove the sample on the tip by pulling up the plug of the syringe; cap and reweigh the syringe. Weigh the sample (accurate to 0.1 mg) by the decrement method. Note 3: If the sample is incompatible with acetone, tetrahydrofuran or a mixed solution of acetone and tetrahydrofuran can be used to dissolve and disperse. Note 4: Spread the to-be-tested sample on the bottom of the vessel (see 4.1); otherwise, the incomplete curing, due to the excessive thickness of the coating film, will lead to large test results. Note 5: Disposable gloves (rubber gloves or polyethylene gloves) shall be worn for all weighing operations during the test. 6.4 Immediately after weighing, place the sample in an oven (see 4.2), and bake at (50±2) °C for 30 min. Note 1: This is a step of simulating the removal of inert solvents in the industrial production stage. Where the sample contains a large amount of solvent, direct curing will lead to a great deviation between the test results and the actual results. Note 2: Alternatively, if it is known that the volatile content in the sample is less than 3%, the step of 6.4 can be omitted and ultraviolet curing can be carried out directly. Note 3: If the sample contains volatile reactive diluents (such as styrene, isobornyl acrylate) at 50 °C, the step of 6.4 cannot be carried out regardless of the volatile content. 6.5 Immediately after taking the sample out of the oven, perform the ultraviolet curing according to the curing requirements specified for the to-be-tested sample. After ultraviolet curing, place it at room temperature for 15 min; weigh the mass (m2) (accurate to 0.1 mg) of the cured sample and vessel (see 4.1). Note: In order to avoid the influence of insufficient ultraviolet curing energy on the experimental results, the curing energy can be increased by 50% for a comparative test. If the test results meet the repeatability requirements, the test results shall be accurate. If the test results do not meet the repeatability ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 33374-2016 be delivered?Answer: The full copy PDF of English version of GB/T 33374-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 33374-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 33374-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 33374-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 33374-2016?A step-by-step guide to download PDF of GB/T 33374-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 33374-2016". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
