GB/T 33282-2016 PDF EnglishUS$145.00 · In stock · Download in 9 seconds
GB/T 33282-2016: General Technical Requirements for Indoor Stone Furniture Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 33282-2016: General Technical Requirements for Indoor Stone Furniture---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT33282-2016GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 97.140 Y 80 General Technical Requirements for Indoor Stone Furniture Issued on: DECEMBER 13, 2016 Implemented on: JULY 01, 2017 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative References ... 4 3 Terms and Definitions ... 6 4 Classification ... 6 5 Requirements ... 6 6 Test Methods ... 14 7 Inspection Rules ... 15 8 Mark, Use Instruction, Package, Transportation and Storage ... 17 Appendix A (Informative) Test Levels of Furniture Mechanical Properties ... 19 General Technical Requirements for Indoor Stone Furniture1 ScopeThis Standard specifies the terms and definitions, classification, requirements, test methods, inspection rules, mark, use instruction, package, transportation, storage of the indoor stone furniture. This Standard is applicable to the design and production of indoor stone furniture products. The outdoor stone furniture can also be referred to.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this document. GB/T 1732 Determination of Impact Resistance of Film GB/T 2828.1-2012 Sampling Procedures for Inspection by Attribute – Part 1. Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-Lot Inspection GB/T 3324-2008 Wooden Furniture - General Technical Requirements GB/T 4893.1 Furniture - Assessment of Surface Resistance to Cold Liquids GB/T 4893.2 Furniture - Assessment of Surface Resistance to Wet Heat GB/T 4893.3 Furniture - Assessment of Surface Resistance to Dry Heat GB/T 4893.4 Test of surface coatings of furniture - Part 4. Determination of adhesion -Cross cut GB/T 4893.7 Test of Surface Coatings of Furniture - Part 7. Determination of Surface Resistance to Alternation of Heat and Cold GB/T 4893.8 Test of Surface Coatings of Furniture - Part 8. Determination of3 Terms and DefinitionsThe following terms and definitions and those ones stipulated in GB/T 28202-2011 and GB/T 13890-2008 are applicable to this document. 3.1 Stone furniture Furniture completely made of stone; or its major components are made of stone. NOTE. The stone contains natural stone and artificial stone. 3.2 Artificial stone The material taking high molecular polymer or cement or a mixture of the two as the bonding material, taking natural stone crushed (powder) and/or natural quartz stone (sand, powder) or aluminum hydroxide powder as the main raw materials, adding pigments and other adjuvants through mixing, solidifying and the like procedures.4 Classification4.1 According to the classification of stone made of the product, it can be divided into. a) Natural stone furniture; b) Artificial stone furniture. 4.2 According to the function, it can be divided into. a) Table-like stone furniture; b) Chair-stool-like stone furniture; c) Cabinet-like stone furniture; d) Bed-like stone furniture.5 Requirements5.1 Major dimension deviation (general item) The limit deviation of the product appearance width, depth and height shall be ±5mm; the limit deviation of the matching or combining product shall take the same positive or negative value.6 Test Methods6.1 Main dimensional deviation, shape and position tolerance test The test on main dimensional deviation, shape and position tolerance shall be performed as per the provisions of 6.1 and 6.2 in GB/T 3324-2008. 6.2 Appearance inspection 6.2.1 Fading, color-losing test 3 positions on the outer surface and interior finishing part of the product shall be tested; use the wet white absorbent gauze to wipe back and forth for three times by hand; the reciprocating distance of the wiping shall be 200mm ~ 300mm. Observe whether the gauze has the color from the painted part. 6.2.2 Test on other appearance test items It shall be measured through the visual examination or steel ruler with accuracy of 0.5mm under the natural light or ambient natural light with light illuminance of 300lx ~ 600lx (for instance, 40W fluorescent lamp), with the sight distance is of 700mm ~ 1000mm. In case of dispute, it shall be tested by 3 persons jointly; the test results shall be subject to the one that is agreed by 2 or more persons. 6.3 Test methods on physical and chemical performance It shall be performed as per the provisions of Table 3. 6.4 Test methods on mechanical properties It shall be performed as per the provisions of Table 4. 6.5 Test on limits of hazardous substances The product stone parts shall be performed as per the provisions of GB 6566. When the product consists of two or more kinds of stones, it needs to be separately sampled and measured. 6.6 Mark Check whether the product has a mark, the content of which shall be checked as per the 8.1. 6.7 Use instructions Check whether the product has use instructions, the content of which shall be checked as per 8.2. 7.2.3.1 Judgment of single product If the product with basic items all qualified, the disqualified general items not exceeding 3 items, then such product shall be qualified; otherwise it is disqualified. 7.2.3.2 Judgement of complete set of products When each product in such set are qualified, then such set of products shall be judged qualified; otherwise it is disqualified. 7.2.3.3 Judgement of batch of products According to the sample size, take the sampling quantity as per the provisions of Table 5; if the number of disqualified products is less than or equal to the acceptance number (Ac), then such batch of products shall be judged qualified; if the number of disqualified products is greater than or equal to rejection number (Re), then such batch of products shall be judged disqualified. 7.3 Type inspection 7.3.1 In addition to all items except the contract requirements, the type inspection also shall be performed in one of the following cases. a) It shall be inspected regularly when the production is officially carried out; the inspection period is generally one year; b) When the raw and auxiliary materials and their production processes undergo major changes; c) When the production is restored after shutdown for half a year or more; d) When the new or old products are performed trial-type identification; e) When the user submits the type inspection or it is required on the ordering contract; f) When the Quality Supervision Department proposed the requirements. 7.3.2 Sampling rules In one inspection cycle, two samples are randomly selected from recently produced products; one for inspection and one for storage. 7.3.3 Inspection procedures The inspection procedures shall try to follow the principle of minimizing the effects on the correctness of the remaining inspection items. c) Control indicators for the limit of the hazardous substance in the product; d) Technical requirements and precautions for product installation and adjustment; e) Product use methods and precautions; f) Product failure analysis and elimination, maintenance methods; g) “Warning instructions. the stone parts are fragile; avoid impacting and dropping”. 8.3 Package The product shall be packaged, the outer package shall have upward mark and a fragile mark to prevent the product from being broken, bumped, scratched or stained. 8.4 Transportation The product shall be protected during the transporting period; prevent the breakage, bumping, deformation, stain or loss, sun and rain. 8.5 Storage When storing the products, they shall be stacked according to the type and specification; when stacking, they shall be placed vertically and the inclination angle shall be ≥75°. Prevent the products from breakage, bumping, deformation, stain or loss, insect damage, sun and rain, mildew. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 33282-2016 be delivered?Answer: The full copy PDF of English version of GB/T 33282-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 33282-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 33282-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 33282-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 33282-2016?A step-by-step guide to download PDF of GB/T 33282-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 33282-2016". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
