GB/T 33241-2025 English PDF

Standard ID	USD	BUY PDF	Lead-Days	Standard Title (Description)	Status
GB/T 33241-2025	RFQ	ASK	3 days	Zinc-aluminum alloy coating section steel	Valid
GB/T 33241-2016	150	Add to Cart	Auto, < 3 mins	Zinc-Aluminum Alloy Coated Section Steel	Valid

Basic data

Standard ID: GB/T 33241-2025 (GB/T33241-2025)
Description (Translated English): Zinc-aluminum alloy coating section steel
Sector / Industry: National Standard (Recommended)
Date of Implementation: 2026-03-01
Older Standard (superseded by this standard): GB/T 33241-2016

GB/T 33241-2016: Zinc-Aluminum Alloy Coated Section Steel

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Zinc-aluminum alloy coated section steel ICS 77.140.70 H44 National Standards of People's Republic of China Zinc-aluminum alloy coated steel Released on December 13,.2016 2017-11-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China China National Standardization Administration issued

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard was proposed by the China Iron and Steel Association. This standard is under the jurisdiction of the National Steel Standardization Technical Committee (SAC/TC183). This standard was drafted. Xiamen New Steel Metal Products Co., Ltd., Xiamen Baofei Dadaoqiao New Technology Co., Ltd., Metallurgical Industry Information Standard Zhun Research Institute, Fujian Haixi Protection New Materials Joint Research Institute Co., Ltd., Xiamen Xinning Steel Co., Ltd. The main drafters of this standard. Zheng Yufei, Zheng Yi, Liu Ge, Zheng Yi, Wang Yuxi, Zheng Long, Zheng Jianwei. Zinc-aluminum alloy coated steel

1 Scope

This standard specifies the terms and definitions, code numbers, models and examples of zinc-aluminum alloy coated steel, ordering content, technical requirements, test methods, Inspection rules, packaging, marking, quality certificates, handling, stacking and storage. This standard is applicable to the section steel (hereinafter referred to as profile steel) of the hot-rolled steel galvanized aluminum alloy layer by continuous hot dip plating.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. GB/T 470 zinc ingot GB/T 706 hot rolled steel General provisions for GB/T 2101 steel acceptance, packaging, marking and quality certificates GB/T 3082-2008 Hot-dip galvanized or hot-dip galvanized-5% aluminum-mixed rare earth alloy coated low carbon steel wire for armored cable GB/T 4956 magnetic substrate on non-magnetic covering layer thickness measurement magnetic method GB/T 6462 metal and oxide coating thickness measurement microscopy GB/T 9793 thermal spray metal and other inorganic coatings zinc, aluminum and their alloys GB/T 11263 hot rolled H-beam and split T-beam GB/T 13825 metal coating ferrous metal material hot-dip galvanized layer unit area mass weighing method Numerical correction of YB/T 081 metallurgical technical standard and determination of test value YS/T 310 zinc alloy ingot for hot plating HG/T 3668 zinc-rich primer

3 Terms and definitions

The following terms and definitions apply to this document. 3.1 Zinc-aluminum alloy coating hotdipzinc-aluminumaloycoating The pretreated steel is immersed in a molten zinc aluminum alloy bath to form a zinc aluminum and/or zinc aluminum iron alloy coating on the surface thereof. 3.2 Plating quality coatingmass The mass of the zinc-aluminum alloy coating per unit area on the surface of the steel is expressed in g/m2. 3.3 Leakage plating uncoatedareas The area where the surface of the section steel does not react with the molten zinc-aluminum alloy. 4 code, model and example 4.1 Code The steel is coded ZA (Z for Zn and A for Al). 4.2 Model The model of zinc-aluminum steel is composed of steel type and steel specifications. Expressed as follows. Steel type Steel specification, in millimeters (mm) 4.3 Example The zinc-aluminum alloy coated H-shaped steel with the specification of 300mm×300mm×10mm×15mm is represented by. ZAHM300×300×10×15

5 Ordering content

Contracts ordered under this standard shall include the following main contents. a) product name; b) the standard number; c) profile steel specifications; d) weight or quantity; e) Special requirements.

6 Technical requirements

6.1 Materials 6.1.1 Steel base metal The steel base metal should meet the requirements of GB/T 706 or GB/T 11263. 6.1.2 Zinc-aluminum alloy ingot The chemical composition of zinc-aluminum alloy ingots shall comply with the requirements of YS/T 310. 6.1.3 Zinc ingot Zinc ingots shall comply with the provisions of GB/T 470. 6.2 Plating 6.2.1 Appearance 6.2.1.1 The surface of the coating shall be smooth and shall not have defects such as peeling, plating, zinc thorn, dripping and slagging. 6.2.1.2 A small amount of white rust on the surface of the steel (white or gray corrosion products based on basic zinc oxide) should not be used as a reason for rejection. 6.2.2 Plating quality and coating thickness The quality of the steel coating and the thickness of the coating shall comply with the requirements of Table 1. Table 1 Steel coating quality and coating thickness Plating Plating quality/(g/m2) not less than Coating thickness/μm not less than Zinc-0.25% aluminum alloy 360 40 Note 1. The requirements for plating quality and coating thickness do not include areas that are repaired due to plating defects or breakage. Note 2. The thickness of the zinc-0.25% aluminum alloy coating listed in the table is calculated according to 7.14g/m2=1μm. Due to factors such as differences in aluminum content in the coating The coating density is not the same, so the coating thickness is only a reference value and is not a basis for delivery. 6.2.3 Plating aluminum content For zinc-0.25% aluminum alloy coating, the aluminum content in the coating should be 0.1%~0.5%. After consultation between the supplier and the buyer and indicated in the contract, Provides other profiles of aluminum-coated steel. 6.2.4 Coating adhesion Profile steel shall not exhibit peeling and peeling of the coating under normal working conditions. Note. The peeling and peeling of the coating caused by bending and deformation after galvanizing aluminum does not mean that the adhesion of the coating is not good. 6.3 Leak plating and repair 6.3.1 Leakage plating The total area of the steel leakage plating surface shall not exceed 0.5% of the total surface area of the part (excluding the cutting part). The area of each missing plating surface should not More than 1cm2, the leakage plating surface should be repaired. When there is no other agreement between the supplier and the buyer, if the plating area is larger than the above specified value, these parts should be given Replating. 6.3.2 Repair If there is a missing plating surface on the surface of the steel, the plating surface should be repaired by coating with zinc-rich paint or hot-sprayed zinc alloy. repair The thickness of the plating in the area should generally be more than 30 μm thicker than the thickness specified in 6.2.2. Before the repair, the scale of the leaking area should be removed. And other contaminants, or other pre-treatment methods to ensure adhesion between the repair layer and the substrate. If repaired with a zinc-rich primer, It shall be carried out in accordance with the requirements of HG/T 3668; if it is repaired by thermal spraying zinc alloy, it shall be carried out in accordance with the requirements of GB/T 9793.

7 Test methods

7.1 Inspection items The inspection items, sampling quantities, sampling methods and test methods for each batch of steel shall comply with the requirements of Table 2. Table 2 Inspection items, sampling quantities, sampling methods and test methods Serial number test item sampling quantity sampling part test method 1 appearance by root - 7.3.1 2 plating quality 3 different branches 7.3.2 3 The aluminum content in the coating is 6 different branches 7.3.3 The mechanical properties and bending properties of the coated steel should meet the requirements of GB/T 706, GB/T 11263 and other related standards. When necessary, these items should be Line inspection. 7.2 Plating inspection 7.2.1 Appearance test Visual inspection under normal lighting conditions using corrected vision. 7.2.2 Coating quality and coating thickness test 7.2.2.1 Weighing method According to the requirements of GB/T 13825. 7.2.2.2 Magnetic method According to the requirements of GB/T 4956. When testing, the test points should be evenly distributed, with at least 5 recorded values per side, and the distance from the edge is not less than 10mm. The test point record value can be increased according to the product specifications. 7.2.2.3 Cross section method According to the requirements of GB/T 6462. 7.2.3 Aluminum content in the coating Inspection shall be carried out in accordance with the provisions of Appendix A of GB/T 3082-2008. 7.2.4 Adhesion test As long as the adhesion of the coating to the substrate can meet the requirements of the part under normal use and general operating conditions, it is usually not necessary to specifically test the coating and The bonding force between the substrates. If the buyer has special requirements, the test method for adhesion may be determined by both the supplier and the buyer.

8 Inspection rules

8.1 Inspection and acceptance Inspection and acceptance of steel sections are carried out by the supplier quality supervision department. The acquirer has the right to conduct any inspection item specified in this standard or contract. Inspection and acceptance. 8.2 Group Batch Rules Steel sections should be accepted in batches. Each batch consists of sections of the same size and size. Each batch is no more than 60t. 8.3 Sampling location and number of samples The sampling location and sampling quantity of each batch of steel shall comply with the requirements of Table 2. 8.4 Re-inspection and judgment The re-inspection and determination of steel sections shall comply with the provisions of GB/T 2101. 8.5 Numerical repair The numerical rounding shall comply with the provisions of YB/T 081. 9 Packaging, marking, quality certificate, handling, stacking and storage 9.1 Packaging 9.1.1 The bundled steel frame, the connection form of the bolt, or the strapping type of the bundle shall be pre-treated. Steel bundle The ends are neat, the layers are distinct, and the thickness is basically the same. The packaging should be firm to ensure that the bales are not loose during transportation, avoiding between steel profiles and sections. Rubbing against the package and damaging the coating. 9.1.2 In addition to the provisions of 9.1.1, the packaging of steel sections shall comply with the provisions of GB/T 2101. 9.2 Mark and quality certificate The steel sign and quality certificate shall comply with the provisions of GB/T 2101. 9.3 Handling, stacking and storage Handling, stacking and storage of steel should pay attention to loading and unloading and place, and the package should not be damaged to deform the product or damage the coating. ......

Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of GB/T 33241-2025_English be delivered?

Answer: Upon your order, we will start to translate GB/T 33241-2025_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of GB/T 33241-2025_English with my colleagues?

Answer: Yes. The purchased PDF of GB/T 33241-2025_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.

Question 5: Should I purchase the latest version GB/T 33241-2025?

Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 33241-2025 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.