GB/T 31248-2014 English PDFUS$909.00 · In stock
Delivery: <= 7 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 31248-2014: Test methods for the measurement of flame spread, heat release and smoke production on electric or optical fibre cables under fire conditions Status: Valid
Basic dataStandard ID: GB/T 31248-2014 (GB/T31248-2014)Description (Translated English): Test methods for the measurement of flame spread, heat release and smoke production on electric or optical fibre cables under fire conditions Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: C84 Classification of International Standard: 13.220.40 Word Count Estimation: 41,477 Date of Issue: 12/5/2014 Date of Implementation: 4/1/2015 Quoted Standard: GB/T 5907; GB/T 16839.1-1997; GB/T 18380.31-2008 Adopted Standard: EN 50399-2011, MOD Regulation (derived from): Announcement of Newly Approved National Standards 2014 No. 27 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Standard specifies under certain experimental conditions, the flame vertically-mounted bunched wires or fiber optic cable spread, heat release and smoke characteristic test apparatus and test methods were evaluated. This Standard applies to the combu GB/T 31248-2014: Test methods for the measurement of flame spread, heat release and smoke production on electric or optical fibre cables under fire conditions---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Test methods for the measurement of flame spread, heat release and smoke production on electric or optical fibre cables under fire conditions ICS 13.220.40 C84 National Standards of People's Republic of China Cable or fiber optic cable by the fire flame spread under conditions Test methods for heat release and smoke production properties Testmethodsforthemeasurementofflamespread, heatreleaseand Issued on. 2014-12-05 2015-04-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ Introduction Ⅳ 1 Scope 1 2 Normative references 1 3 Terms and definitions 4 test apparatus 2 4.1 Overview 2 3 4.2 Air Supply System Smoking 3 cover 4.3 4.4 exhaust pipes 4 4.5 exhaust pipe testing equipment 5 4.6 Fan 7 4.7 smoke density measurement device 7 4.8 flue gas analysis equipment 8 Calibration of the test apparatus 95 5.1 Overview 9 Flow distribution measuring 5.2 9 5.3 sampling lag time measurement 9 5.4 Debugging Calibration 9 10 5.5 General Calibration 6 Test Procedure 10 6.1 Test conditions 10 6.2 Test Sample 10 6.3 Sample preparation 11 6.4 the number of samples to determine the 11 6.5 specimen mount 11 Volume flow within the pipe 13 6.6 6.7 ignition source 13 6.8 time for fire 13 6.9 Test procedure 13 6.10 observation and tests in the test 14 6.11 Test Security 14 14 7 Evaluation of test results 7.1 determine the degree of flame spread 14 7.2 heat release rate (HRR) and smoke production rate (SPR) parameter calculation 14 8 15 test reports Appendix A (informative) The revised standard clauses and EN50399.2011 reg number control and technical differences and their causes Appendix B (normative appendix) HRRav, SPRav and FIGRA Calculation 18 Annex C (normative) heat release rate 20 Annex D (normative) Tobacco 22 Annex E (informative) Figure 5 Additional information about Reynolds 23 Annex F (normative) Calibration debugging 24 Traffic Appendix G (normative) pipeline distribution 31 Calibration procedure in Appendix H (informative) special measuring equipment 33 References 35ForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. This revised standard adopts EN50399.2011 "by the cable Common test methods for cables under fire conditions in the flame propagation Test Heat release and smoke production properties of test test equipment, procedures and results "(in English). Taking into account China's national conditions, in the use of EN50399.2011, the standard of this made some changes, and differences relating to technical reasons attached Listed in Appendix A for reference. For ease of use, the standard EN50399.2011 made the following editorial changes. --- Standard name has been modified to suit our habits; --- Will be the "European standards" be replaced by "this standard"; --- Remove the foreword EU standards and some references; --- With a decimal point "." Instead of a comma as the decimal point "." The standard proposed by the People's Republic of China Ministry of Public Security. This standard by the National Standardization Technical Committee for fire protection material Technical Committee (SAC/TC113/SC7) centralized. This standard is drafted by. Ministry of Public Security of Sichuan Fire Research Institute. Participated in the drafting of this standard. DuPont China Holding Co., Ltd. (Suzhou) International Trade Co., Ltd. CommScope, Belden's Hirschmann network system EC International Trading (Shanghai) Co., Ltd., Daikin Fluorine Chemical (China) Co., resistance Kesen Kai News (Shanghai) Cable Co., Ltd., Solvay (on Sea) Ltd., 3M China Ltd, China Motion Industries (Suzhou) Co., Ltd. The main drafters of this standard. Li Feng, Cheng Daobin, Feng, including Mitsuhiro, Rui Hu, Zhu Yaming, Zeng Xu Bin. This standard is the first release.IntroductionThis standard describes the medium-scale fire tests were bunched cable or fiber optic cable. The test will be mounted on vertical cable ladder standard used Ignition source specified ignition, in order to evaluate the burning behavior of cables and combustion properties. It can be obtained by testing the cable fire early stages Combustion performance data, spread by the heat release rate testing to reflect the risk of flame along the cable as well as the potential source of ignition Movies adjacent areas Rang through the smoke density test reflects the risk of fire and smoke visibility area of \u200b\u200bpersonal safety posed. Test cable or cables can be obtained following properties under certain combustion conditions. --- Flame spread; --- Heat release rate; --- Total heat release; --- Tobacco rate; --- Total amount of smoke; --- Burning growth rate index; --- Burning droplets/particles. The test device based on GB/T 18380.31-2008 "burning test and optical fiber cables under fire conditions - Part 31. Vertical Bunched wires or cables installed vertical flame spread test test device "(IEC 60332-3-10.2000, IDT) establish, while increasing the heat Release and smoke production properties of test equipment. Compared with GB/T 18380.31-2008, this standard has a sensitive test method is more accurate and comprehensive Stronger, the combustion performance rating evaluation more scientific characteristics. The actual installation of the cable structure may affect the actual fire flame spread, an important factor in heat release and smoke generation, and therefore the test Special attention should affect the actual installation of the cable to the relevant measurement data. These measurements depend on the following factors. a) exposed to heat or flame volume cable itself and an external fire burning combustible material; b) the geometry of the cable, and the relationship between test space enclosure structures; c) the release of gases from the cable ignition temperature; Under d) the given temperature conditions, from the cable released amount of combustible gas; e) combustion air flow through the cable; f) the structure of the cable, such as armored or non-armored, multi-core or single core. This standard determines the cable installation conditions, including exposure to the material volume, the test standard cable ladder geometry, and by burning Air flow combustion chamber. These standardized conditions for Burning Behavior cable provides the foundation. Cable or fiber optic cable by the fire flame spread under conditions Test methods for heat release and smoke production properties1 ScopeThis standard specifies under certain experimental conditions, the flame vertically mounted bunched wires or fiber optic cable spread, heat release and smoke special Test equipment and test methods for the evaluation of conduct. This standard applies to the combustion performance evaluation for electric cables. Note. The "wires and cables" mentioned in this standard, including all metal conductors insulated cables for power or signal transmission.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 5907 fire first part basic terms GB/T 16839.1-1997 Thermocouples - Part 1. indexing table (IEC 60584-1.1995, IDT) GB/T 18380.31-2008 burning test and optical fiber cables under fire conditions - Part 31. electrical wire bundles vertically mounted Cable vertical flame spread test test equipment (IEC 60332-3-10.2000, IDT)3 Terms and DefinitionsGB/T 5907 defined by the following terms and definitions apply to this document. 3.1 Heat release rate heatreleaserate HRR Under specified conditions, material in unit time by the release of heat of combustion. 3.2 Total heat release totalheatrelease THR Heat release rate within the specified time integral value. Example. THR1200 represented by the fire in the 1200s the total heat release. 3.3 Tobacco rate smokeproductionrate SPR The amount of smoke generated per unit time. 3.4 Tobacco Total totalsmokeproduction TSP Smoke production rate within a specified time integral value. Example. TSP1200 represents the total amount of smoke produced by the fire in the 1200s. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 31248-2014_English be delivered?Answer: Upon your order, we will start to translate GB/T 31248-2014_English as soon as possible, and keep you informed of the progress. The lead time is typically 4 ~ 7 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 31248-2014_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 31248-2014_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
