GB/T 3098.5-2016 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 3098.5-2016: Mechanical properties of fasteners -- Tapping screws Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 3098.5: Historical versions
Similar standardsGB/T 3098.5-2016: Mechanical properties of fasteners -- Tapping screws---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3098.5-2016GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 21.060.10 J 13 Replacing GB/T 3098.5-2000 Mechanical Properties of Fasteners – Tapping Screws (ISO 2702.2011, Heat-Treated Steel Tapping Screws – Mechanical Properties, MOD) Issued on: FEBRUARY 24, 2016 Implemented on: JUNE 1, 2016 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 6 2 Normative References ... 6 3 Materials ... 6 4 Technical Requirements ... 6 5 Acceptance ... 8 6 Test Methods ... 8ForewordGB/T 3098 Mechanical Properties of Fasteners include the following parts. --- GB/T 3098.1 Mechanical Properties of Fasteners - Bolts, Screws and Studs; --- GB/T 3098.2 Mechanical Properties of Fasteners - Nuts; --- GB/T 3098.3 Mechanical Properties of Fasteners - Set Screws; --- GB/T 3098.5 Mechanical Properties of Fasteners - Tapping Screws; --- GB/T 3098.6 Mechanical Properties of Fasteners - Stainless Steel Bolts, Screws and Studs; --- GB/T 3098.7 Mechanical Properties of Fasteners - Thread Rolling Screws; --- GB/T 3098.8 Mechanical Properties of Fasteners - Components for Bolted Connections Made Mainly from Materials with a High Temperature Strength; --- GB/T 3098.9 Mechanical Properties of Fasteners - Prevailing Torque Type Steel Hexagon Nuts; --- GB/T 3098.10 Mechanical Properties of Fasteners - Bolts, Screws, Studs and Nuts Made of Non-Ferrous Metals; --- GB/T 3098.11 Mechanical Properties of Fasteners - Drilling Screws with Taping Screw Thread; --- GB/T 3098.12 Mechanical Properties of Fasteners - Cone Proof Load Test on Nuts; --- GB/T 3098.13 Mechanical Properties of Fasteners - Torsional Test and Minimum Torques for Bolts and Screws with Nominal Diameters 1mm to 10mm; --- GB/T 3098.14 Mechanical Properties of Fasteners - Widening Test on Nuts; --- GB/T 3098.15 Mechanical Properties of Fasteners - Nuts Made of Stainless- Steel; --- GB/T 3098.16 Mechanical Properties of Fasteners - Stainless Steel Set Screws; --- GB/T 3098.17 Mechanical Properties of Fasteners - Preloading Test for the Detection of Hydrogen Embrittlement - Parallel Bearing Surface Method; --- GB/T 3098.18 Mechanical Properties of Fasteners - Blind Rivets Testing; --- GB/T 3098.19 Mechanical Properties of Fasteners - Blind Rivets with Break Pull Mandrel; --- GB/T 3098.20 Mechanical Properties of Fasteners - Wing Nuts with Specified Proof Torque; --- GB/T 3098.21 Mechanical Properties of Fasteners - Stainless Steel Tapping Screws; --- GB/T 3098.22 Mechanical Properties of Fasteners - Made of the Fine Grain Non- Heat Treatment Steel - Bolts, Screws and Studs. This Part belongs to Part 5 of GB/T 3098. This Part was drafted as per the rules specified in GB/T 1.1-2009. This Part replaced GB/T 3098.5-2000 Mechanical Properties of Fasteners - Tapping Screws; compared with GB/T 3098.5-2000, the major technical changes are as follows. --- Increase Thread Specification ST 9.5 (Chapter 1); --- Reduce the maximum hardness of the core from 390HV to 370HV (4.1.3); --- Add “use the calibrated torque-measuring device according to provision of 3.2.2 in GB/T 3098.13” (6.2.2). This Part adopts the re-drafting method to modify and use ISO 2702. 2011 Heat- Treated Steel Tapping Screws – Mechanical Properties (English Edition). The technical differences and causes between this Part and ISO 2702. 2011 are as follows. --- In the Normative References, use national standards to replace international standards (Chapter 2); add the reference of GB/T 5280 (Chapter 1), so that conform to basic China fastener standard. This Part also makes the following editorial changes. --- Modify the standard name; --- Delete the bibliography of ISO 2702. This Part was proposed by China Machinery Industry Federation. This Part shall be under the jurisdiction of National Technical Committee for Standardization of Fasteners (SAC/TC 85). Drafting organization of this Part. China Productivity Center for Machinery. Participating drafting organizations of this Part. Machinery Industry General Product Mechanical Properties of Fasteners - Tapping Screws1 ScopeThis Part of GB/T 3098 specifies the materials, technical requirements and test methods of tapping screws. This Part is applicable to the tapping screws manufactured by carburizing carbon steel, thread specification of ST2.2~ST9.5; and thread conforms to the provisions of GB/T 5280.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this standard. GB/T 3098.13-1996 Mechanical Properties of Fasteners - Torsional Test and Minimum Torques for Bolts and Screws with Nominal Diameters 1mm to 10mm (idt ISO 898-7.1992) GB/T 4340.1 Metallic Materials - Vickers Hardness Test - Part 1. Test Method (GB/T 4340.1-2009, ISO 6507-1.2005, MOD) GB/T 5280 Tapping Screws Thread (GB/T 5280-2002, idt ISO 1478.1999)3 MaterialsThe tapping screws shall be manufactured by the cold heading and carburizing carbon steel.4 Technical Requirements4.1 Metallic phase 4.1.1 Surface hardness The surface hardness of tapping screws after heat treatment shall be ≥450HV0.3 (see5 AcceptanceThe conventional acceptance test can only include screw-in performance, breakaway torque and core hardness test; however, for the arbitration, all technical requirements specified in Chapter 4 shall be met.6 Test Methods6.1 Metallic phase test 6.1.1 Surface hardness test The Vickers-hardness test shall conform to the provisions of GB/T 4340.1. The surface hardness test shall be performed on the plane, and preferentially on the head of the tapping screw. 6.1.2 Carburized layer depth – metallic phase method The carburized layer depth test shall be performed on the side of the thread, the measuring point shall be at the 1/2 distance between tooth top and tooth bottom. For the tapping screw with thread specification≤ST3.9, it shall be measured on the tooth bottom. The arbitration test shall be performed on the thread profile by the test force with micro Vickers hardness of 300g. The carburized layer depth shall be calculated since the point with core hardness of 30 HV. 6.1.3 Core Hardness test The core hardness test shall conform to the provisions of GB/T 4340.1, and perform on the 1/2 cross section of the sufficient distance (with complete minor diameter of thread) away from the tapping screw end. 6.1.4 Microstructure test The microstructure test shall be performed as per the metallic phase test standard. 6.2 Mechanical property test 6.2.1 Screw-in property test Screw-in the tapping screw specimen (during acceptance period, with or without coatings) into the test plate, till a complete thread totally passes through the test plate. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 3098.5-2016 be delivered?Answer: The full copy PDF of English version of GB/T 3098.5-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 3098.5-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3098.5-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3098.5-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 3098.5-2016?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3098.5-2016 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 3098.5-2016?A step-by-step guide to download PDF of GB/T 3098.5-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 3098.5-2016". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
