GB/T 30474.2-2013 English PDFUS$139.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 30474.2-2013: Holding fixtures of cylindrical abrasive sleeves -- Part 2: Holding fixtures for stationary machines Status: Valid
Basic dataStandard ID: GB/T 30474.2-2013 (GB/T30474.2-2013)Description (Translated English): Holding fixtures of cylindrical abrasive sleeves -- Part 2: Holding fixtures for stationary machines Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J43 Classification of International Standard: 25.100.70 Word Count Estimation: 6,673 Quoted Standard: GB/T 30473-2013 Adopted Standard: ISO 15637-2-2002, MOD Regulation (derived from): National Standards Bulletin 2013 No. 27 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: The standard provides for a fixed set of cylindrical grinding machine sand on the clamping device of the type, size, requirements, marks, logos. This standard applies to comply with GB/T 30473 in D> 100mm clamping device cylindrical sleeve sand used. Such GB/T 30474.2-2013: Holding fixtures of cylindrical abrasive sleeves -- Part 2: Holding fixtures for stationary machines---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Holding fixtures of cylindrical abrasive sleeves Part 2.. Holding fixtures for stationary machines ICS 25.100.70 J43 National Standards of People's Republic of China Sand cylindrical sleeve clamp Part 2. clamping device for stationary grinding machine Part 2. Holdingfixturesforstationarymachines (ISO 15637-2.2002, MOD) Issued on. 2013-12-31 2014-10-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordGB/T 30474 "cylindrical sand sets of clamping devices" is divided into the following two parts. --- Part 1. take-up shaft for a handheld grinder on the clamping device; --- Part 2. clamping device for stationary grinding machines. This section GB/T Part of 230,474. This section drafted in accordance with GB/T 1.1-2009 given rules. This section uses redrafted Law Amendment uses ISO 15637-2. Stationary grinding for.2002 "cylindrical sand sets of clamping devices - Part 2 Clamping means "cutting machine. This part of ISO 15637-2.2002 technical differences and the reasons are as follows. --- Deleted in size, content suppliers and importers flag (see Chapter 6), in order to meet the actual domestic production, sale and use of Happening. For ease of use, this section made the following editorial changes. a) increase the range of the content requirements; Adoption of international standards by GB b) normative references equivalents/T 30473-2013 instead of ISO 2421.2003. Technical differences exist compared to 2002, the terms of these differences have been involved through gaps in its outer margin. This part of ISO 15637-2 Vertical single-line position (|) were marked. This part is proposed by China Machinery Industry Federation. This part of the National Standardization Technical Committee Abrasives (SAC/TC139) centralized. This section is drafted. Henan University. The main drafters of this section. Li Cheng Shin. Sand cylindrical sleeve clamp Part 2. clamping device for stationary grinding machine1 ScopeGB/T 30474 provisions of this section for cylindrical grinding machine sand sleeve fixed on the clamping device type, size, requirements, marking, Mark. This section applies to a GB/T 30473 in D > 100mm clamping devices barrel sleeve sand used. Such clamping device use Different ways of clamping sleeve cylindrical sand, for example, a sheet core or pneumatic devices.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 30473-2013 coated abrasives sand cylindrical sleeve (ISO 2421.2003, IDT)3 type and sizeType 3.1 Shape and type of clamping device by the manufacturer custom; only shall comply with the dimensions and tolerances. see picture 1. Shape and type of clamping device schematically in Fig. 1 3.2 Dimensions Size Table 1. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 30474.2-2013_English be delivered?Answer: Upon your order, we will start to translate GB/T 30474.2-2013_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 30474.2-2013_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 30474.2-2013_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
