GB/T 28780-2024 English PDFUS$359.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 28780-2024: Safety of machinery - Integral lighting system used for machines Status: Valid GB/T 28780: Historical versions
Basic dataStandard ID: GB/T 28780-2024 (GB/T28780-2024)Description (Translated English): Safety of machinery - Integral lighting system used for machines Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J09 Classification of International Standard: 13.110 Word Count Estimation: 18,119 Date of Issue: 2024-04-25 Date of Implementation: 2024-11-01 Older Standard (superseded by this standard): GB/T 28780-2012 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 28780-2024: Safety of machinery - Integral lighting system used for machines---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.ICS 13:110 CCSJ09 National Standards of People's Republic of China Replaces GB/T 28780-2012 Overall lighting system for mechanical safety machines Released on 2024-04-25 2024-11-01 Implementation State Administration for Market Regulation The National Standardization Administration issued Table of ContentsPreface III Introduction IV 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Technical Requirements 2 5 Lighting equipment and installation 3 6 Inspection methods 4 7 Usage Information 5 Appendix A (informative) Examples of lighting installation 6 References 9ForewordThis document is in accordance with the provisions of GB/T 1:1-2020 "Guidelines for standardization work Part 1: Structure and drafting rules for standardization documents" Drafting: This document replaces GB/T 28780-2012 "Integral lighting of mechanical safety machines": Compared with GB/T 28780-2012, except for the In addition to logical changes, the main technical changes are as follows: --- Changed the scope of the statement (see Chapter 1, Chapter 1 of the:2012 edition); --- Changed the expression of general requirements in the technical requirements for the overall lighting system for machines (see 4:1, 4:1 of the:2012 edition); --- Added the ergonomic principles of the overall lighting system for machines and the relevant provisions of emergency lighting (see 4:7 and 4:8); --- Changed the content of lighting equipment and installation (see Chapter 5, Chapter 5 of the:2012 edition); --- Changed the title and content of Chapter 6 (see Chapter 6, Chapter 6 of the:2012 edition); --- Changed the information for use (see Chapter 7, Chapter 7 of the:2012 edition): Please note that some of the contents of this document may involve patents: The issuing organization of this document does not assume the responsibility for identifying patents: This document is proposed and coordinated by the National Technical Committee for Machinery Safety Standardization (SAC/TC208): This document was drafted by: Nan'an Zhongji Standardization Research Institute Co:, Ltd:, Jiangxi Zhangshu Fuling Internal Combustion Engine Parts Co:, Ltd:, Ji'an Igor Electric Co:, Ltd:, Guoxun Technology (Xiamen) Co:, Ltd:, Yangzhou Kangle Machinery Co:, Ltd:, Huzhou Nanxun District Baitong Standardization Research Institute, Shandong Jie Chuang Machinery Co:, Ltd:, Nanjing Zhongtuo Technology Co:, Ltd:, Zhejiang Huafeng Electric Tools Co:, Ltd:, Guangdong Dangjia Intelligent Electric Co:, Ltd:, Nanjing Forestry University, Pilz Electronics (Changzhou) Co:, Ltd:, Aohuang Testing Technology Service (Shanghai) Co:, Ltd:, China Machine Productivity Promotion Center Co:, Ltd:, Quanzhou Standardization Association, Beijing Mechanical Equipment Research Institute, Chengdu Aerospace Kate Electromechanical Technology Co:, Ltd:, Beijing Institute of Technology, Guangqi Honda Automobile Co:, Ltd:, Sichuan Shuxing Youchuang Safety Technology Co:, Ltd:, Shenzhen Danse Display Technology Co:, Ltd:, Fuzhou Jiantianzhong Machinery Technology Co:, Ltd:, Quanzhou Jinli Engineering Machinery Co:, Ltd:, Shenzhen Jintian International Intelligent Robot Co:, Ltd:, Fujian Quancheng Special Equipment Technology Co:, Ltd:, Guangdong Mingkai Technology Co:, Ltd:, Yiwu Limai New Materials Co:, Ltd:, Guangdong Kangxin New Materials Co:, Ltd:, Suzhou Institute of Quality and Standardization, Shandong Gada Testing Co:, Ltd:, Guangdong Zhenyu Technology Co:, Ltd:, Shaoxing Keyi Standard Technology Consulting Co:, Ltd:, Dongguan Qiandao Machinery Manufacturing Co:, Ltd:, and Shenzhen China Optoelectronics Co:, Ltd: The main drafters of this document are: Chen Liping, Zheng Huating, Li Renfu, Zhang Peng, Zhao Kegang, Zhang Lei, Zheng Chuansen, Sun Bisheng, Zhang Tianze, Chen Yong, Zhang Jie, Wang Li, Jiang Huixing, Zhao Maocheng, Li Zhong, Huang Zhijiong, Huang Fei, Zhang Chong, Li Qin, Ju Ronghua, Liu Zhiyong, Jiang Liping, Ju Likai, Zeng Yicong, Wu Haijian, Qin Peijun, Zhang Yan, Wang Feng, Fu Huiqing, Huang Zhiming, Zeng Huashan, Zhou Ping, Li Binyang, Li Taicong, Cheng Hongbing, Zhang Xiaofei, Chen Yonglong, Wang Zhesi, Xia Yan, Zhao Juan, Zhang Shuo, Zhang Biying, Gu Dazheng, Cao Yongsheng, and Wang Junjun: This document was first published in:2012 and this is the first revision:IntroductionThe categories of safety standards in the machinery field are as follows: --- Category A standards (basic safety standards) give basic concepts, design principles and general characteristics applicable to all machinery: --- Class B standards (general safety standards) involve a safety feature of a machine or a type of safety device with a wide range of use: ● Category B1, safety features (such as safety distance, surface temperature, noise) standards; ● Category B2, safety device (such as two-hand control device, interlocking device, pressure sensitive device, protective device) standards: ---Category C standards (machine safety standards) are standards that specify detailed safety requirements for a specific machine or a group of machines: According to GB/T 15706-2012, this document belongs to Class B standard: This document is particularly relevant to the following stakeholders involved in machinery safety: ---Machine manufacturer; ---Health and safety agencies: Other stakeholders affected by the level of machinery safety are: ---Machine users; ---Machine owner; ---Service providers; --- Consumer (for machinery intended for use by consumers): All of the above stakeholders may participate in the drafting of this document: In addition, the standardization body that drafts the Type C standard is also the intended user of this document: The requirements specified in this document are refined, supplemented or modified by Category C standards: For machines within the scope of Category C standards and designed and manufactured in accordance with Category C standards, the requirements in Category C standards shall take precedence: In order to illuminate the working area inside and outside the machine, an integral lighting system (located inside or outside the machine) is required: The system needs to achieve certain performance to enable the operator to use the machine safely during work, maintenance and repair: Overall lighting system for mechanical safety machines1 ScopeThis document specifies the technical requirements, lighting equipment and installation, inspection methods and usage information for the overall lighting system for machines: This document applies to the design, installation and conformity assessment of the overall lighting system inside and outside the machine: This document does not apply to machine integrated lighting systems operating in the following environments: --- Extreme environmental conditions (such as the environment inside refrigeration equipment or high temperature equipment); ---Special environmental conditions (such as explosive, corrosive, etc:); --- Environmental conditions with very low visibility caused by smoke, mist, dust, etc:2 Normative referencesThe contents of the following documents constitute the essential clauses of this document through normative references in this document: For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to This document: GB/T 5226:1-2019 Electrical safety of machinery Electrical equipment of machinery Part 1: General technical requirements GB/T 5226:31 Electrical safety of machinery - Electrical equipment of machinery - Part 31: Special requirements for sewing machines, sewing units and sewing systems Safety and EMC requirements GB/T 5226:32 Electrical safety of machinery Electrical equipment of machinery Part 32: Technical conditions for lifting machinery GB/T 5226:33 Electrical safety of machinery Electrical equipment of machinery Part 33: Technical requirements for semiconductor equipment GB 7000 (all parts) Lighting GB/T 15706 General principles for safety design of machinery - Risk assessment and risk reduction GB/T 18153 Safety of machinery - Ergonomic data for determining hot surface temperature limits - Accessible surface temperature GB/T 20138 Protection level of electrical equipment enclosure against external mechanical impact (IK code)3 Terms and definitionsThe terms and definitions defined in GB/T 15706 and the following apply to this document: 3:1 Machinery machine It is composed of several parts connected and has a specific application purpose, at least one of which is movable and is equipped with or pre- A combination of power systems is required: Note: The term "machine" also includes several machines arranged and controlled so as to function as a complete machine for the same application: combination: [Source: GB/T 15706-2012, 3:1, modified] 3:2 A system permanently installed on a machine, consisting of a lighting source, lamps and their associated control devices: ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 28780-2024_English be delivered?Answer: Upon your order, we will start to translate GB/T 28780-2024_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 28780-2024_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 28780-2024_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 28780-2024?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 28780-2024 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
