GB/T 2650-2022 PDF EnglishUS$125.00 · In stock · Download in 9 seconds
GB/T 2650-2022: Destructive tests on welds in metallic materials - Impact tests Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 2650: Historical versions
GB/T 2650-2022: Destructive tests on welds in metallic materials - Impact tests---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT2650-2022GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 25.160.40 CCS J 33 Replacing GB/T 2650-2008 Destructive Tests on Welds in Metallic Materials – Impact Tests (ISO 9016:2022, Destructive Tests on Welds in Metallic Materials – Impact Tests – Test Specimen Location, Notch Orientation and Examination, MOD) ISSUED ON: OCTOBER 12, 2022 IMPLEMENTED ON: OCTOBER 12, 2022 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative References ... 5 3 Terms and Definitions ... 5 4 General ... 5 5 Sampling Code ... 6 5.1 Sampling code system ... 6 5.2 Characters ... 6 5.3 Additional information ... 6 6 Code Example ... 7 7 Test Procedure ... 9 8 Test Report ... 9 Appendix A (Informative) Example of Test Report ... 10 Destructive Tests on Welds in Metallic Materials – Impact Tests1 ScopeThis Document specifies the sampling code, code example, test procedure and test report for the impact test of welded butt joints. This Document applies to impact tests of fusion welded and pressure welded joints of metallic materials. This Document is a supplement to GB/T 229, including the sampling code of butt joint specimens and additional reporting requirements.2 Normative ReferencesThe provisions in following documents become the essential provisions of this Document through reference in this Document. For the dated documents, only the versions with the dates indicated are applicable to this Document; for the undated documents, only the latest version (including all the amendments) is applicable to this Document. GB/T 229 Metallic materials - Charpy pendulum impact test method (GB/T 229-2020, ISO 148-1:2016, MOD)3 Terms and DefinitionsFor the purposes of this Document, there are no terms and definitions apply.4 GeneralThe impact specimen shall be taken horizontally from the welded joint; and the longitudinal axis of the specimen is perpendicular to the length direction of the weld. The notch location can be determined by macroscopic erosion. The impact test shall be carried out according to the provisions of GB/T 229. The test temperature, sampling location, specimen type, specimen size and notch orientation shall comply with the provisions of relevant application standards.5 Sampling Code5.1 Sampling code system The sampling code system consists of letters indicating the specimen type, location and notch direction, and numbers indicating the distance (in mm) between the notch and the reference line RL. See Tables 1 and 2 for the sampling code representation method. 5.2 Characters The sampling code consists of the following characters: First character: Use "U" for Charpy U-notch; "V" for Charpy V-notch. The second character: Use "W" to indicate that the notch is in the weld metal; at this time, the reference line RL is the centerline of the weld on the specimen. Use "H" to indicate that the notch is in the heat-affected zone; and at this time the reference line RL is vertical line drawn from the intersection of the longitudinal central axis and fusion line/pressure welding bonding line to the surface of the base metal. Third character: Use "S" to indicate that the notched face is parallel to the surface of the joint/test piece. NOTE 1: The direction of the notched surface parallel to the surface of the joint/test piece is equivalent to the meaning of "surface notch" in the fracture mechanical test. Use "T" to indicate that the notched face is perpendicular to the surface of the joint/test piece (the notch passes through the thickness of the joint/specimen). The fourth character: Use "α" to indicate the distance from the axis of the notch to the reference line (if the centerline of the notch is the centerline of the weld metal, record α=0). The fifth character: Use "b" to indicate the distance between the surface of the joint/test piece and the surface of the nearest side of the specimen (if the surface of the specimen is the surface of the joint, record b=0). NOTE 2: For X-shaped, K-shaped or similar welds, the surface of the weld is the wider side of the weld or the side where the welding starts. 5.3 Additional information When the above sampling codes cannot fully describe the specimen location or the notch orientation, a schematic diagram prepared according to the welding procedure specification should be provided. 1 – notch axis; 2 – base metal; 3 – heat affected zone; 4 – fusion line; 5 – weld metal. Figure 1 – Typical Sampling Code Example7 Test ProcedureThe specimens marked in this Document shall be tested according to the provisions of GB/T 229.8 Test ReportIn addition to the requirements specified in GB/T 229, the test report shall also include the following: a) The reference number of this Document: such as GB/T 2650-2022; b) Specimen sampling code; c) If any, give the type and size of the observed imperfections; d) If necessary, give a schematic diagram; e) Other contents required by the application of standards and/or agreements. Appendix A gives an example of a typical test report. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 2650-2022 be delivered?Answer: The full copy PDF of English version of GB/T 2650-2022 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 2650-2022_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 2650-2022_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 2650-2022 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 2650-2022?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 2650-2022 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 2650-2022?A step-by-step guide to download PDF of GB/T 2650-2022_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 2650-2022". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
