GB/T 25832-2019 PDF EnglishUS$150.00 · In stock · Download in 9 seconds
GB/T 25832-2019: Hot rolled steel plate and strip for porcelain enameling Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 25832: Historical versions
Similar standardsGB/T 25832-2019: Hot rolled steel plate and strip for porcelain enameling---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT25832-2019NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.140.50 H 46 Replacing GB/T 25832-2010 Hot rolled steel plate and strip for porcelain enameling ISSUED ON: JUNE 04, 2019 IMPLEMENTED ON: MAY 01, 2020 Issued by: State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Designation representation method and classification ... 6 4 Ordering contents ... 8 5 Dimension, shape, weight ... 9 6 Technical requirements ... 9 7 Test methods ... 14 8 Inspection rules ... 14 9 Packaging, marking and quality certificate ... 15 Annex A (informative) Comparison of new and old designations of this Standard ... 16 Hot rolled steel plate and strip for porcelain enameling1 ScopeThis Standard specifies the designation representation method and method [Translator note: should be “classification”], ordering contents, dimension, shape, weight, technical requirements, test methods, inspection rules, packaging, marking and quality certificate of hot rolled steel plates and strips for porcelain enameling. This Standard is applicable to hot rolled steel plates and strips with good porcelain enameling properties and thickness of not more than 40 mm, used in industries such as light industry, household appliances, metallurgy, construction, chemical equipment, water treatment industry (hereinafter referred to as steel plates and strips).2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 222 Permissible tolerances for chemical composition of steel products GB/T 223.3 Methods for chemical analysis of iron, steel and alloy - The diantipyryl methane phosphomolybdate gravimetric method for the determination of phosphorus content GB/T 223.9 Iron, steel and alloy - Determination of aluminium content - Chrome azurol S photometric method GB/T 223.17 Methods for chemical analysis of iron, steel and alloy - The diantipyryl methane photometric method for the determination of titanium content GB/T 223.40 Iron, steel and alloy - Determination of niobium content - The sulphochlorophenol S spectrophotometric method GB/T 223.58 Methods for chemical analysis of iron, steel and alloy - The extraction-absorption catalytic polarographic method for the determination of manganese content GB/T 232 Metallic materials - Bend test GB/T 247 General rule of package, mark and certification for steel plates (sheets) and strips GB/T 709 Dimension, shape, weight and tolerances for hot-rolled steel plates and sheets GB/T 2975 Steel and steel products - Location and preparation of test pieces for mechanical testing GB/T 4336 Carbon and low-alloy steel - Determination of multi-element contents - Spark discharge atomic emission spectrometric method (routine method) GB/T 8170 Rules of rounding off for numerical values & expression and judgement of limiting values GB/T 17505 Steel and steel products - General technical delivery requirements GB/T 20066 Steel and iron - Sampling and preparation of samples for the determination of chemical composition GB/T 20123 Steel and iron - Determination of total carbon and sulfur content - Infrared absorption method after combustion in an induction furnace (routine method) GB/T 20125 Low-alloy steel - Determination of multi-element contents - Inductively coupled plasma atomic emission spectrometric method3 Designation representation method andclassification 3.1 Designation representation method The steel designation consists of three parts: a letter representing the yield strength, the minimum value of specified lower yield strength and a classification code. Among them, it adds a quality grade symbol for the classification of steel for porcelain enameling for chemical equipment, and when the quality grade symbol is omitted, it is supplied according to Grade B. Example: Q245GTD Q - The first letter of Chinese Pinyin of “Qu” in yield strength; - hot rolled pickled surface. The hot rolled pickled surface is suitable for continuously hot rolled steel plates and strips. 3.4 Surface quality grade The surface quality grade consists of: - normal grade surface FA; - higher grade surface FB.4 Ordering contents4.1 Contracts or orders ordered in accordance with this Standard shall include the following: a) serial number of this Standard; b) product name (steel plate or steel strip); c) designation; d) delivery condition; e) dimension and flatness accuracy; f) surface condition; g) surface quality grade; h) weight; i) edge condition; j) use; k) special requirements. 4.2 When the surface condition is not indicated in the contract, it is delivered by hot rolled surface. When the surface condition is hot rolled pickled surface, and the contract does not indicate whether it is oiled, it is delivered after oiling. When the surface quality grade is not indicated in the contract, the surface is delivered by normal grade.7 Test methods7.1 The test methods for various inspection items of steel plates and strips shall comply with the provisions of Table 9. 7.2 The chemical composition test of steel is generally carried out according to GB/T 4336, GB/T 20123 or general chemical analysis method. In case of arbitration, it is carried out according to the provisions of GB/T 223.3, GB/T 223.9, GB/T 223.17, GB/T 223.40, GB/T 223.58, GB/T 223.59, GB/T 223.60, GB/T 223.61, GB/T 223.62, GB/T 223.63, GB/T 223.64, GB/T 223.67, GB/T 223.68, GB/T 223.69, GB/T 223.71, GB/T 223.72, GB/T 223.79 and GB/T 20125. Table 9 -- Inspection item, sampling quantity, sampling method and test method No. Inspection item Sampling quantity Sampling method Test method 1 Chemical analysis 1 (each furnace number) GB/T 20066 See 7.2 2 Tensile test 1/batch GB/T 2975 GB/T 228.1 3 Bending test 1/batch GB/T 2975 GB/T 232 4 Impact test 1 set (3)/batch GB/T 2975 GB/T 229 5 Dimension, shape — — Suitable measuring tools 6 Surface quality Piece by piece/coil by coil — Visual inspection8 Inspection rules8.1 Inspection and acceptance Inspection and acceptance of steel plates and strips shall be carried out by the supplier's technical supervision department. 8.2 Batching rules Steel plates and strips shall be accepted in batches. Each batch shall consist of steel plates or strips of the same designation, the same furnace number, the same delivery condition, the same thickness, the same rolling system and the same surface condition. 8.3 Sampling quantity Sampling method and sampling quantity of each batch of steel plates and strips are shown in Table 9. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. |
