GB/T 25753.3-2011 English PDFUS$229.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 25753.3-2011: Vacuum technology -- Roots vacuum pump -- Measurement of performance characteristics -- Part 3: Measurement of overflow valve differential pressure Status: Valid
Basic dataStandard ID: GB/T 25753.3-2011 (GB/T25753.3-2011)Description (Translated English): Vacuum technology -- Roots vacuum pump -- Measurement of performance characteristics -- Part 3: Measurement of overflow valve differential pressure Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J78 Classification of International Standard: 23.160 Word Count Estimation: 10,193 Date of Issue: 2011-11-21 Date of Implementation: 2012-06-01 Regulation (derived from): Announcement of Newly Approved National Standards No. 18 of 2011 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the Roots vacuum relief valve differential pressure measurement method. GB/T 25753 This part applies to pumping speed of 30 L/s ~ 20 000 L/s Roots vacuum pump (hereinafter referred to as the pump). This section does not apply to the performance of Roots vacuum pump ultimate pressure and pumping rate measurements. GB/T 25753.3-2011: Vacuum technology -- Roots vacuum pump -- Measurement of performance characteristics -- Part 3: Measurement of overflow valve differential pressure---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. .. Vacuum technology Roots vacuum pump Measurement of performance characteristics Part 3. Measurement of overflow valve differential pressure ICS 23.160 J78 National Standards of People's Republic of China Roots vacuum pumps - Measurement of performance art Part 3. Measurement of differential pressure relief valve characteristics-Part 3. Measurementofoverflowvalvedifferentialpressure Issued on. 2011-11-21 2012-06-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ Introduction Ⅳ 1 Scope 1 2 Terms and definitions 1 3 apparatus 1 4 TEST CONDITIONS 4 Test Method 4 5 6 Test Results 4 7 Test Report 4ForewordGB/T 25753 "Roots vacuum pumps - Measurement of performance art" is divided into three parts. --- Part 1. The maximum allowable differential pressure measurement; --- Part 2. Zero flow compression ratio measurement; --- Part 3. Measurement of differential pressure relief valve. This is Part 3 GB/T 25753 of. This section drafted in accordance with GB/T 1.1-2009 given rules. This part is proposed by China Machinery Industry Federation. This part of the National Vacuum Technology Standardization Technical Committee (SAC/TC18) centralized. This section is responsible for drafting. Zhejiang Vacuum Equipment Group Co., Ltd. Participated in the drafting of this section. Chengdu South-ray machines Limited, Shenyang Institute of Scientific Instrument Development Center Co., Ltd., Shandong Zibo Vacuum Equipment Co., Ltd., Shanghai Huifeng Petrochemical Co., Ltd., Taizhou Global Vacuum Equipment Manufacturing Co., Ltd., Shenyang Vacuum Technology Institute The study. The main drafters of this section. Wang Xi, Wang Xiaohu, Xu Tao, Fanlin Dong, Wang Guangyu, Xu Jian law, benefits Jinde Zhao meter spring, Zhao Weisheng, Lingling, ROCKETS.IntroductionWith the development of basic industries and design innovation, design and performance Roots pump structure have made considerable Progress early Roots vacuum pumps must rely on pre-pump operation, and now the development of a direct atmospheric discharge run-cooled Roots Roots vacuum pumps and wet, the other a single series Roots vacuum pump has become the single-stage single-stage, two-stage, multi-stage, rotor profile also Futaba become the double leaf, clover, leafy. Existing Roots vacuum pump performance measure contains only a single-stage double-lobe Roots pump, other types not covered by the basic, and not To regulate the pressure relief valve on the measurement method, in order to effectively improve the Roots vacuum pump performance measurement standards compatibility and applicability, the actual inspection Experimental measurements provide the necessary operating instructions, from home and abroad in a wide range of relevant indicators, benchmarks, based on the actual situation, the development of the "vacuum technology Roots vacuum pumps - Measurement of performance art "standard, to form a single sequence, and is divided into three parts. It will be based on the future status of technological development into Line the necessary changes and expansion. Roots vacuum pumps - Measurement of performance art Part 3. Measurement of differential pressure relief valve1 ScopeGB/T 25753 provisions of this part of the measurement methods Roots vacuum relief valve differential pressure. GB/T 25753 apply to this part of the pumping speed of 30L/s ~ 20000L/s Roots vacuum pump (hereinafter referred to as the pump). This section does not Roots vacuum pump is suitable for the performance of extreme pressure and pumping speed measurements.2 Terms and definitionsThe following terms and definitions apply to this document. 2.1 Pressure relief valve overflowvalvedifferentialpressure Roots vacuum pump pressure relief valve is the difference between pre-stage pressure relief valve inlet pressure when carried off Movement. 2.2 Test cover testdome Special vacuum vessel having a predetermined precise shape and dimensions, through which the gas to be measured into the pump, a pressure measuring means mounted thereon.3 devices3.1 Test cap As shown in Figure 1, the shape of a cylinder. The axial dimension of the cover is 1.5D, D is the inner diameter of the housing. Test gas inlet is located in the axis of the cover On the connection flange and the distance is D, arranged in the intake port should be such that the gas from the direction away from the pump into the test port cover. Measuring the inlet pressure Gauge distance 0.5D connecting flange at its axis is perpendicular to the axis of the cover. Testing should cover the axis perpendicular to the pump inlet flange plane. In addition to the intake line, the connecting line between the flange and the test covers the inner wall of the test should not wear a cap. VD test cover volume should be at least one compression cycle pump swept five times the volume of the VP. In the pump inlet should be connected to a reducer fittings, Its length should not exceed 0.5D (see Figure 1). Different specifications of the pump for test cover given in Table 1. Table 1 Test parameters cover VP/L VD/LD/mm 0 0.26 1.3 100 160 1.1 5.4 0.26 ~ 1.1 ~ 4.2 21250 4.2 ~ 1784400 17 to 65 325 630 65 - 26013001000 260 to 106,053,001,600 1060 - 4060203002500 ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 25753.3-2011_English be delivered?Answer: Upon your order, we will start to translate GB/T 25753.3-2011_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 25753.3-2011_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 25753.3-2011_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
