GB/T 25396.1-2025 English PDFUS$679.00 · In stock
Delivery: <= 5 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 25396.1-2025: Agricultural machinery - Thrown-object test and acceptance criteria - Part 1: Rotary mowers Status: Valid GB/T 25396.1: Historical versions
Basic dataStandard ID: GB/T 25396.1-2025 (GB/T25396.1-2025)Description (Translated English): Agricultural machinery - Thrown-object test and acceptance criteria - Part 1: Rotary mowers Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: B91 Classification of International Standard: 65.060.50 Word Count Estimation: 34,380 Date of Issue: 2025-08-01 Date of Implementation: 2026-02-01 Older Standard (superseded by this standard): GB/T 25396-2010 Issuing agency(ies): State Administration for Market Regulation, Standardization Administration of China GB/T 25396.1-2025: Agricultural machinery - Thrown-object test and acceptance criteria - Part 1: Rotary mowers---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT25396.1-2025 ICS 65.060.50 CCSB91 National Standard of the People's Republic of China Partially replaces GB/T 25396-2010 Specification for testing and acceptance of thrown objects from agricultural machinery Part 1.Rotary lawn mowers Part 1.Rotary mowers (ISO 17101-1.2012,MOD) Released on August 1, 2025 Implementation on February 1, 2026 State Administration for Market Regulation The National Standardization Administration issued Table of ContentsPreface III Introduction V 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Projectile test 2 4.1 Test conditions 2 4.2 Target Plate 3 4.3 Test materials 16 4.4 Test conditions 17 4.5 Test procedures 17 4.6 Test results and reports 19 4.7 Acceptance Rules 19 Appendix A (Informative) Lawn Mower Example 20 A.1 This document covers lawn mowers 20 A.2 Lawn mowers not covered by this document 21 Appendix B (Normative) Test Report on Throwouts from Rotary Mowers 24 Reference 27 Figure 1 Target plate partition 4 Figure 2 Partition reference line 5 Figure 3 Arrangement of partitions 5, 7a and 7b in the operator area Figure 4 Target plate layout of side-mounted rotary mower 10 Figure 5 Target plate arrangement of an upright rotary mower mounted on a tractor's rear three-point hitch 11 Figure 6 Target plate arrangement for front-mounted or self-propelled rotary mowers 13 Figure 7 Target plate layout for trailed and semi-mounted rotary mowers 14 Figure 8 Rotary mower target plate layout 15 Figure 9 Example of a cone-shaped material pile forming device 17 Figure 10 Target plate material pile location 18 Figure A.1 Self-propelled lawn mower 20 Figure A.2 Rotary disc mower 20 Figure A.3 Rotary Cylinder Mower 21 Figure A.4 Lawn mower with conditioning device 21 Figure A.5 Flail mower 22 Figure A.6 Lawn mower with articulated arm 22 Figure A.7 Inter-row mowing unit 23 Table 1 Dimensions of the partitions 5, 7a and 7b in Figure 3a) Table 2 Dimensions of partitions 5, 7a and 7b for narrow tractors in Figure 3b) Table B.1 Product Information 24 Table B.2 Main test report 25 Table B.3 Additional test report 26 Preface This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1.Structure and drafting rules for standardization documents" Drafting. This document is Part 1 of GB/T 25396 “Test and Acceptance Specification for Throwable Objects of Agricultural Machinery”. The following two parts have been published. --- Part 1.Rotary lawn mowers; --- Part 2.Flail mowers. This document partially replaces GB/T 25396-2010 "Agricultural machinery rotary and flail mowers - throwable objects test and acceptance test Compared with GB/T 25396-2010, in addition to structural adjustments and editorial changes, the main technical changes are as follows. a) The "Scope" has been changed (see Chapter 1, Chapter 1 of the.2010 edition); b) Added the terms and definitions of “trip” and “test” (see Chapter 3); c) The term "straw board" was changed to "slat collecting device" and the definitions of the terms "kraft paper" and "impact" were changed (see Chapter 3,.2010 Chapter 3 of the.2011 edition); d) The requirement for the length of the target plate extending into the lower area has been deleted (see 4.2.1 of the.2010 edition); e) Added Figures 1 and 2 (see 4.2.2); f) The height of the partition frame has been changed (see 4.2.2.3, 4.2.1 of the.2010 edition); g) Added the applicable conditions of partition 5 in the operator area of rotary mowers, and added the applicable conditions of traction and semi-mounted rotary mowers The requirements for the partition 5 of the machine are increased, and the layout of the partitions 5, 7a, and 7b in the operator area of the rotary mower when the narrow tractor is pulled is increased. For layout and dimensions, Figure 3b) and Table 2 (see 4.2.3) were added; h) Changed the dimensions and ground clearance of the partitions 5, 7a, 7b in the operator area of the rotary mower when towed by a standard tractor. Figure 3a) and Table 1 (see 4.2.3, 4.2.2 of the.2010 edition); i) Changed Figure 4 and the position requirements for the side-mounted rotary mower partitions 1 and 4 mounted on the tractor's rear three-point hitch (see 4.2.4, 4.2.3 of the.2010 edition); j) Changed Figure 5 to modify the use of the upright rotary mower baffles 7a and 7b mounted on the tractor's rear three-point hitch. Conditions and location requirements of 1a and 1b (see 4.2.5, 4.2.4 of the.2010 edition); k) Figure 6 has been modified (see 4.2.6, 4.2.5 of the.2010 edition); l) Changed Figure 7 to change the position requirements of partitions 1 and 4 for trailed and semi-mounted rotary mowers (see 4.2.7,.2010 edition). 4.2.6); m) Figure 8 has been modified to change the position of the partition 1 of the towed rotary mower that can be mounted on the right, middle or left side of the tractor. Installation requirements (see 4.2.8, 4.2.7 of the.2010 edition); n) Figure 7 of the.2010 edition has been deleted (see 4.4.1 of the.2010 edition); o) Deleted the principles for handling impact points in special circumstances (see 4.5 of the.2010 edition); p) Figure 10 has been modified (see 4.5, 4.4.2 of the.2010 edition); q) Added the test result recording method and test report requirements (see 4.6); r) The acceptance rules have been changed (see 4.7, 4.6 of the.2010 edition); s) Added Appendix B (Normative) Test Report on Throwable Objects from Rotary Mowers. This document is modified to adopt ISO 17101-1.2012 "Agricultural machinery throwable objects test and acceptance code Part 1.Rotary mowing machine". This document has the following structural adjustments compared to ISO 17101-1.2012. ---3.2 corresponds to 3.3 in ISO 17101-2.2012, and the title number of the same level clause is postponed; --- Added the title of 4.1.1.1, 4.1.1.2 corresponds to 4.1.1.1 in ISO 17101-2.2012, and 4.1.1.3 corresponds to ISO 17101- 2.4.1.1.2 in.2012; --- Added the title of 4.2.1, and the title numbers of the same level articles are postponed accordingly. The technical differences between this document and ISO 17101-1.2012 and their reasons are as follows. --- Deleted the term "flail mower" (see Chapter 3); --- Added the requirement of "adjust the mower according to the instruction manual so that it can work normally" (see 4.1.1.1) to improve the test safety. All-encompassing; --- The normative reference GB/T 451.2 replaces ISO 536, GB/T 454 replaces ISO 2758, and GB/T 455 replaces ISO 1974.2012 (see 4.2.2.1) to adapt to my country's technical conditions and increase operability; --- Changed the position requirements for the partition 4 of the side-mounted rotary mower mounted on the rear three-point hitch of the tractor (see 4.2.4) to Improve trial safety; --- Changed the position requirements of the partitions 1a and 1b of the upright rotary mower mounted on the tractor's rear three-point hitch (see 4.2.5) to improve the safety of the test; --- Changed the position requirements of partitions 1 and 4 for towed and semi-mounted rotary mowers (see 4.2.7) to improve test safety; --- The normative reference GB/T 3871.3 replaces ISO 789-1.1990 (see 4.4.1) to adapt to my country's technical conditions and increase Increase operability. The following editorial changes have been made to this document. --- Replaced ISO 4254-13 with the informative reference GB/T 10395.26 (see Chapter 1); --- Replaced ISO 4254-12 with the informative reference GB/T 10395.25-2020 (see 3.1); --- Added a note to "sand saturation moisture content" (see 4.3.2). Please note that some of the contents of this document may involve patents. The issuing organization of this document does not assume the responsibility for identifying patents. This document was proposed by the China Machinery Industry Federation. This document is under the jurisdiction of the National Technical Committee for Agricultural Machinery Standardization (SAC/TC201). This document was drafted by. Hohhot Branch of China Agricultural Mechanization Research Institute Co., Ltd., Shandong Agricultural University, Inner Mongolia Huade Grass Machinery Co., Ltd., Inner Mongolia Autonomous Region Agricultural and Animal Husbandry Technology Promotion Center, China Agricultural Mechanization Research Institute Group Co., Ltd. Company, Zhejiang Jiarui Machinery Co., Ltd., Ningbo Ruilin Machinery Technology Co., Ltd., Xiuyi (Fujian) Garden Engineering Co., Ltd., Taizhou Rongtian Technology Co., Ltd., Wenling Daxi Aofeng Capacitor Factory, Zhejiang Lvju Vehicle Industry Co., Ltd., and Taizhou Yiku New Energy Technology Co., Ltd. The main drafters of this document are. He Gang, Sun Wenting, Song Zhanhua, Wang Zhenhua, Wang Qiang, Li Fade, Zhai Gaixia, Bao Zhiliang, Su Jiajia, Yang Li, Gao Yunbo, Wuyuntana, Hou Chong, Zhao Xiaojuan, Hu Jun, Gao Xiaohong, Lu Limeng, Dong Jiajia, Yang Jinghao, Jin Ya, Liu Liping, Shao Yu, Wang Junyue, Qu Bozhe, Zhang Ping, Xu Tian, Zhao Xiaofeng, Guo Wei, Yang Yating, Bao Wuyunbilige, and Xu Chen. This document was first published as GB/T 25396-2010 in.2010, and this is the first revision.introductionAs a key equipment in agricultural production, the safety and reliability of agricultural mowers not only directly affect the life and property of operators, but also directly affect the safety and reliability of agricultural mowers. Safety is more related to the overall improvement of agricultural production efficiency. During the operation of the lawn mower, the high-speed cutting element may Foreign objects such as debris are thrown out, posing a potential threat to the operator and the surrounding environment. To ensure the safe use of the lawn mower, a scientific and standardized throwing Product testing and acceptance criteria are particularly important. Agricultural machinery lawn mowers include rotary lawn mowers and flail lawn mowers. The ejection test methods and acceptance specifications have both commonalities and differences. In order to specify the test and acceptance standards for the thrown objects of different types of lawn mowers, the test and acceptance standards for the thrown objects of lawn mowers are divided into two categories. part. --- Part 1.Rotary mowers. The purpose is to specify the test conditions, methods and procedures for the thrown objects test of agricultural machinery rotary mowers. Methods, contents and acceptance criteria. --- Part 2.Flail mowers. The purpose is to specify the test conditions and methods for the thrown objects test of agricultural machinery flail mowers. Methods, contents and acceptance criteria. Specification for testing and acceptance of thrown objects from agricultural machinery Part 1.Rotary lawn mowers1 ScopeThis document specifies the test and acceptance criteria for ejection objects for rotary mowers, agricultural machinery. This document applies to rotary lawn mowers, see the example given in Appendix A, A.1. This document does not apply to the following models (see A.2 for examples). ---Fluff mower; --- Lawn mowers equipped with articulated arms; --- Mowers with one or more vertical axes designed for bedding; ---Pedestrian-controlled electric lawn mowers; ---Gardening lawn mower; ---Inter-row mowing unit; ---Rotary mowers designed for highway and road maintenance use only. NOTE 1 If the lawn mower is also intended for non-agricultural use, it must meet the other ejection test requirements in addition to the requirements of this document. Note 2.For the test and acceptance specifications for thrown objects from flail mowers, see GB/T 25396.2. Note 3.For the test and acceptance specifications for ejection from rotary lawn mowers with cutting element diameters greater than 1000 mm, see GB/T 10395.26.2 Normative referencesThe contents of the following documents constitute the essential clauses of this document through normative references in this document. For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to This document. GB/T 451.2 Paper and board—Determination of basis weight (GB/T 451.2-2023, ISO 536.2019, MOD) GB/T 454 Paper - Determination of Burst Strength (GB/T 454-2020, ISO 2758.2014, MOD) GB/T 455 Paper and board—Determination of tear resistance (GB/T 455-2002, eqvISO 1974.1990) GB/T 3871.3 Agricultural tractor test procedures Part 3.Power take-off shaft power test (GB/T 3871.3- 2006, ISO 789-1.1990, MOD)3 Terms and DefinitionsThe following terms and definitions apply to this document. 3.1 Rotary mower rotarymower It has one or more cutting parts rotating around a vertical axis, which cut or shear the forage in an impact manner without covering the cut forage Lawn mower on the ground. [Source. GB/T 10395.25-2020, 3.2, modified] ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 25396.1-2025_English be delivered?Answer: Upon your order, we will start to translate GB/T 25396.1-2025_English as soon as possible, and keep you informed of the progress. The lead time is typically 3 ~ 5 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 25396.1-2025_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 25396.1-2025_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 25396.1-2025?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 25396.1-2025 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
