GB/T 24159-2022 PDF EnglishUS$455.00 · In stock · Download in 9 seconds
GB/T 24159-2022: Welded insulated cylinders Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 24159: Historical versions
Similar standardsGB/T 24159-2022: Welded insulated cylinders---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT24159-2022NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 23.020.30 CCS J 74 Replacing GB/T 24159-2009 Welded insulated cylinders Issued on. JULY 11, 2022 Implemented on. FEBRUARY 01, 2023 Issued by. State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 7 4 Symbols... 8 5 Model naming methods and basic parameters... 9 6 Materials... 10 7 Design... 11 8 Manufacturing... 17 9 Inspection methods... 25 10 Inspection rules... 29 11 Marking, packaging and transportation... 32 12 Exit-factory data... 33 13 Data preservation... 34 Annex A (normative) Maximum allowable filling coefficient... 35 Annex B (normative) Valve inlet and outlet joints... 37 Annex C (Normative) Safe discharge volume and discharge area... 40 Annex D (normative) Vibration test... 47 Annex E (normative) Drop test... 49 Annex F (informative) Product certification... 52 Annex G (informative) Batch inspection quality certificate... 551 ScopeThis document specifies the symbols for welded insulated gas cylinders (hereinafter referred to as "cylinders"). It specifies cylinder model naming methods, basic parameters, materials, design, manufacturing, test methods, inspection rules, type test, marking, packaging, transportation, exit-factory data, data preservation and other requirements. This document is applicable to the refillable cylinders that are used under normal ambient temperature (-40℃~60℃), are used to store liquid oxygen, liquid nitrogen, liquid argon of which the nominal volume range is 10L~1000L, the nominal volume of LNG ranges from 150L to 1000L, that the design temperature is not higher than -196℃, and the nominal working pressure is 0.2MPa~3.5MPa. For cylinders storing liquid carbon dioxide and liquid nitrous oxide, the manufacture and inspection can be carried out with reference to this document. NOTE. All pressures not stated in this document refer to gauge pressure.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 228.1, Metallic materials - Tensile testing - Part 1.Method of test at room temperature GB/T 229, Metallic materials - Charpy pendulum impact test method GB/T 1804, General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications GB/T 2653, Bend test methods on welded joints GB/T 7144, Coloured cylinder mark for gases GB/T 9251, Hydrostatic test method for gas cylinders GB/T 12137, Methods for leakage test of gas cylinders GB/T 12241, Safety valves - General requirements GB/T 12243, Spring loaded safety valves GB/T 13005, Terminology of gas cylinders GB/T 15384, Designation for gas cylinders GB/T 16804, Precautionary labels for gas cylinders GB/T 16918, Bursting disc safety devices for gas cylinders GB/T 17925, Standard practice for X-ray digital radioscopic examination of cylinder weld3 Terms and definitionsFor the purposes of this document, the terms and definitions defined in GB/T 12241, GB/T 13005, GB/T 16918, GB/T 18442.1, GB/T 18442.3, GB/T 18443.2, GB/T 18517, GB/T 26929, GB/T 33209 and GB/T 33215 as well as the followings apply. 3.1 lot/batch A quantity of product (or inner vessel) composed according to the same rules. 3.2 tare of cylinder The mass of the empty cylinder (for horizontal gas cylinder, it includes frame or support) that meets the basic functions of filling, storage, transportation, use and safety. 3.3 effective volume The maximum volume of liquid that the cylinder is allowed to fill. 3.4 heat transfer coefficient The amount of heat that can be transferred between hot and cold fluids in unit area, unit temperature difference, unit time, representing the strength of the heat transfer process. 3.5 free air Air at an absolute pressure of 1.01325×105 Pa and a temperature of 15.6°C.4 SymbolsThe following symbols apply to this document. Di. Inner diameter of head or cylinder body, mm. D0.Outer diameter of head or cylinder body, mm. E0.Elastic modulus of the material, MPa. g. Acceleration of gravity, g=9.81m/s2. Hi. Inner height of head, equal to the sum of the depth of the inner surface of the head and the height of the straight edge of the head, mm. hi. Depth of the inner surface of the head, mm. h0.Total height of the outer surface of the head, h0=hi+Sn; mm. k1.Coefficient determined by the ratio of the major and minor axes of the ellipse. L. Sum of the length of the cylinder, the height of the straight side of each head, and 1/3 of the depth of the inner surface, mm. P. Nominal working pressure, MPa. Pb. Design burst pressure of rupture disc, MPa. Sh. Minimum wall thickness of the head after forming, mm. Sn. Nominal wall thickness, mm. σ. Wall stress, MPa. ΔHi. Height tolerance inside the head, mm. ΔπDi. Tolerance of the inner circumference of the head, mm.5 Model naming methods and basic parameters5.1 Model naming methods Vertical type is represented by "DPL". Horizontal type is represented by "DPW". The rest are named according to the method specified in GB/T 15384.When the design is changed, Roman numerals I, II, III, etc. can be added at the end of the model as serial numbers. 5.2 Basic parameters 5.2.1 Nominal volume and inner diameter of inner vessel The nominal volume and inner diameter of the inner vessel shall be selected according to Table 1.The nominal volume shall be an integer multiple of 5. 5.2.2 Pressure 5.2.2.1 The pressure used in the calculation of the internal pressure of the wall thickness of the inner vessel is the design pressure. The design pressure is the pressure test pressure of the inner vessel. The pressure of withstand voltage test of the inner vessel shall not be less than 2 times the nominal working pressure (Pd=Pt≥2P). 5.2.3 Effective volume6 Materials6.1 General requirements 6.1.1 The material of the main body (cylinder and head) of the inner vessel shall be austenitic stainless steel that meets the requirements of GB/T 24511 and the requirements of the design documents. 6.1.2 The components welded on the inner vessel shall be austenitic stainless steel specified in the corresponding material standards and in accordance with the requirements of the design documents. 6.1.3 The chemical composition and tensile properties of welding materials and their deposited metals shall comply with the requirements of NB/T 47018.1 and NB/T 47018.3 as well as the requirements of design documents. 6.1.5 The outer shell shall be of austenitic stainless steel. 6.2 Chemical composition The chemical composition and allowable deviation of the main material of the inner vessel shall comply with the provisions of Table 2. 6.3 Mechanical properties The mechanical properties of the main material of the inner vessel shall comply with the provisions of Table 3 and design documents.7 Design7.1 General requirements 7.1.1 Composition 7.1.2 Connecting piece between inner vessel and outer shell The stress value of the connecting piece between the inner vessel and the outer shell shall not be greater than 2/3 of the material's normal temperature yield strength (or specified plastic extension strength) under the following independent loads. 7.1.3 Performance indicators The leakage rate of vacuum interspace and the leakage rate of vacuum interspace are as specified in Table 4.The static evaporation rate with the nominal working pressure not greater than 2.4MPa is in accordance with the provisions of Table 4. 7.1.4 Maximum filling volume and maximum filling mass 7.1.5 Design service life The design service life shall not exceed 20 years. It shall be indicated in the design document and used as the content of the nameplate. 7.1.6 Accessories 7.1.6.1 The cleanliness of accessories that come into contact with oxygen, such as valves, pressure gauges, safety pressure relief devices and liquid level gauges, shall meet the requirements of 8.13.2. 7.4.3 Safety pressure relief device 7.4.3.1 The main safety pressure relief device and the auxiliary safety pressure relief device shall be arranged in parallel. The main safety pressure relief device shall use safety valves. The auxiliary safety pressure relief device of LNG is only allowed to use safety valves. The auxiliary safety pressure relief device for the rest of the medium shall be safety valve or bursting disc safety device. 7.4.3.2 The set pressure of the main safety relief device (safety valve) shall not be greater than 1.2 times the nominal working pressure (Pz≤1.2P). The discharge pressure shall meet the following requirements. 7.4.3.3 The auxiliary safety pressure relief device is only applicable to the situation of C.1.2.It shall meet the following requirements. 7.5 Pressure relief device of outer shell The outer shell shall be provided with a pressure relief device to meet the following requirements.8 Manufacturing8.1 Responsibilities of manufacturer 8.2 Batching 8.2.1 Manufacture according to inner vessel batches. The material batch number of the same batch of inner vessel shall not exceed two. Product batches are carried out on the basis of inner vessel batches. The same inner vessel batch shall be one product batch, or it can be composed of multiple product batches. 8.2.2 The quantity of a batch of inner vessels shall not be more than 200 (excluding destructive inspection bottles). 8.3 Material re-inspection The main material of the inner vessel shall be re-inspected for chemical composition according to the furnace number. The mechanical properties shall be re-inspected according to the batch number. The mechanical property test specimens shall be taken along the direction perpendicular to the rolling direction of the steel plate. 8.5 Unspecified tolerance The grades without linear and angular dimensional tolerances are in accordance with the provisions of GB/T 1804.The machined surface is medium grade m. Non-machined surfaces are rough grade c. 8.6 Cylinder body 8.7 Head 8.7.1 The steel plates used to make the head shall not be spliced. The wall stress value of the liner head shall not be greater than the wall stress value of the liner barrel. 8.7.2 After the head is formed, there shall be no mutations, cracks, peeling, wrinkles and other defects. The wall thickness shall meet the requirements of 7.2, 7.3 and design documents. 8.7.3 The shape and size tolerance of the head shall be inspected in accordance with the provisions of GB/T 25198.The results shall meet the requirements of Table 6. 8.8 Connection joints 8.9 Assembly 8.9.1 Components shall be checked before assembly. The pressure components are not allowed to be strongly aligned and leveled. 8.9.3 The components welded on the inner cylinder body shall avoid the longitudinal and circumferential welded joints of the inner cylinder body. 8.9.4 The connection between the base, frame and hoisting accessories and the cylinder body shall avoid the longitudinal and circumferential welds of the outer shell. 8.10 Welding 8.10.1 Welding preparation and welding environment 8.10.2 Groove requirements There shall be no cracks, delamination, inclusions and other defects on the groove surface. Before welding, the groove and other harmful impurities such as oxides, oil stains and other harmful impurities shall be removed within at least 20mm of the surface of the base metal on both sides (calculated by the groove edge). 8.10.3 Qualification of inner vessel welding procedure 8.12 Withstand voltage test of inner vessel 8.12.1 The withstand voltage test of inner vessel shall be carried out one by one after the non-destructive testing is qualified. 8.12.2 The test shall have reliable safety protection measures. It is confirmed and approved by the technical person in charge of the manufacturer or the person in charge of safety production. 8.12.3 The test shall use two pressure test instruments with the same range and within the validity period of the verification. The range is 1.5 times to 3 times the test pressure (shall be 2 times the test pressure). The accuracy is not less than level 1.6.The diameter of the mechanical dial is not less than 100mm. 8.12.4 During the test, welded joints with leakage shall be repaired in accordance with the provisions of 8.10.4.5.After passing the test, perform the withstand voltage test again. 8.12.5 The pressure shall not drop during the pressure holding check. There shall be no leakage, visible macroscopic deformation and abnormal sound. 8.13 Surface quality and cleanliness 8.13.1 There shall be no defects on the surface of the sheet that will affect normal use. For sharp scratches, grinding shall be carried out. The maximum grinding slope shall be 1.3.Grinding shall be smooth and clean. After grinding, the thickness of the inner vessel meets the requirements of 7.2.The thickness of the outer shell meets the requirements of 7.3. 8.13.2 Components forming (or in) a vacuum space shall be cleaned of hydrocarbons (oil, grease and so on), decontaminated. Good protection measures shall be taken after disposal. Residual hydrocarbons shall not exceed 125mg/m2 after treatment of parts in direct contact with oxygen. 8.14 Air tightness test9 Inspection methods9.1 Main materials of inner vessel For re-inspection of chemical composition and mechanical properties of main material of inner vessel, when using domestic materials, the test methods and inspection requirements shall be carried out in accordance with the provisions of GB/T 24511. 9.2 Wall thickness determination Wall thickness shall be measured with ultrasonic thickness gauge or vernier caliper and other tools according to the frequency specified in Table 7. 9.3 Welding specimens of inner vessel products Tensile test method for welded specimens of inner vessel products is in accordance with the provisions of GB/T 228.1.The impact test method is in accordance with the provisions of GB/T 229 (impact temperature is not higher than -192℃). The bending test method is in accordance with the provisions of GB/T 2653. 9.4 Nondestructive testing 9.5 Withstand voltage test of inner vessel 9.6 Surface quality and cleanliness The treatment method of surface quality and cleanliness shall be in accordance with the provisions of JB/T 6896.Choose appropriate method for components of vacuum space. For the parts that are in direct contact with oxygen, it shall use the oil concentration measurement method. Use quality method to treat hydrocarbons. 9.7 Leakage rate of vacuum interspace Before vacuuming, test according to the method specified in GB/T 18443.3. 9.8 Leakage and deflation rate of vacuum interspace At the end of vacuuming, test according to the method specified in GB/T 18443.4. 9.9 Air tightness test After the accessories such as valves, instruments and safety pressure relief devices are assembled, they shall be tested in accordance with the methods specified in GB/T 12137. 9.10 Low temperature vacuum After filling with liquid nitrogen and reaching thermal equilibrium, measure according to the method specified in GB/T 18443.2. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 24159-2022 be delivered?Answer: The full copy PDF of English version of GB/T 24159-2022 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 24159-2022_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 24159-2022_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 24159-2022 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 24159-2022?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 24159-2022 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 24159-2022?A step-by-step guide to download PDF of GB/T 24159-2022_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 24159-2022". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
