GB/T 2411-2008 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 2411-2008: Plastics and ebonite -- Determination of indentation hardness by means of a durometer (shore hardness) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 2411: Historical versions
Similar standardsGB/T 2411-2008: Plastics and ebonite -- Determination of indentation hardness by means of a durometer (shore hardness)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT2411-2008 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.080 G 31 GB/T 2411-2008 / ISO 868.2003 Replacing GB/T 2411-1980 Plastics and ebonite - Determination of indentation hardness by means of a duronmeter (shore hardness) (ISO 868.2003, IDT) Issued on: AUGUST 04, 2008 Implemented on: APRIL 01, 2009 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Principle... 5 4 Apparatus... 6 5 Test specimens... 8 6 Calibration... 9 7 Conditioning and testing atmospheres... 10 8 Procedure... 10 9 Test report... 10ForewordThis Standard equivalently adopts ISO 868.2003 Plastic and Hard Rubber - Using Sclerometer to Determine Indentation Hardness (Shore Hardness) (English version). This Standard equivalently translates ISO 868.2003; it has the same technical contents. In order for ease of use, this Standard makes the following editorial changes. a) Change “this international standard” into “this Standard”; b) Delete foreword of ISO 868.2003; c) Add foreword of national standard; d) Replace the international standards listed in “Normative references” by the national standards that equivalently adopt the corresponding international standards; e) Change the international standards involved in this Standard into the corresponding national standards. This Standard replaces GB/T 2411-1980 Plastics - Shore hardness test. Compared with GB/T 2411-1980, the main changes are as follows. — Change name of standard and add foreword; — Expand the application scope; add hard rubber; — Add normative documents; — Thickness of sample AND distance between measured point and sample edge are different; — Verification and installation of sclerometer spring are in standard text; — Give the hardness determination indication time fluctuation range; — Representation of testing results is different; — Add contents of test report; — Delete the annex. This Standard was proposed by China Petroleum and Chemical Industry Association. This Standard shall be under the jurisdiction of National Plastic Technical Committee for Standardization (SAC/TC 15). Plastics and ebonite - Determination of indentation hardness by means of a duronmeter (shore hardness)1 Scope1.1 This Standard specifies a method for the determination of the indentation hardness of plastics and ebonite by means of durometers of two types. type A is used for softer materials and type D for harder materials (see the Note to 8.2). The method permits measurement either of the initial indentation or of the indentation after a specified period of time, or both. NOTE. The durometers and the methods specified in this Standard are referred to as type A Shore and type D Shore durometers and durometer methods, respectively. 1.2 This method is an empirical method intended primarily for control purposes. No simple relationship exists between indentation hardness determined by this method and any fundamental property of the material tested. For specification purposes, it is recommended that GB/T 6031-1998 Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10IRHD and 100 IRHD), be used for the softer materials.2 Normative referencesThe articles contained in the following documents have become part of this Standard when they are quoted herein. For the dated documents so quoted, all the modifications (excluding corrections) or revisions made thereafter shall not be applicable to this Standard. For the undated documents so quoted, the latest editions shall be applicable to this Standard. GB/T 2918-1998 Plastics — Standard atmospheres for conditioning and testing (idt ISO 291.1997)3 PrincipleA specified indenter is forced into the test material under specified conditions and the depth of penetration measured. The indentation hardness is inversely related to the penetration and is dependent on the modulus of elasticity and the viscoelastic properties of the material. The shape of the indenter, the force applied to it and the duration of its application influence the results obtained so that there may be no simple relationship between the results obtained with one type of durometer and those obtained with either another type of durometer or7 Conditioning and testing atmospheres7.1 For materials whose hardness is not dependent on the relative humidity, the durometer and test specimens shall be conditioned at the temperature of test (see 7.2) for at least 1 h before testing. For materials whose hardness is dependent on the relative humidity, the test specimens shall be conditioned in accordance with GB/T 2918-1998, or in accordance with the relevant material specification. When a durometer is moved from a location below room temperature to a location with a higher temperature, it shall be placed in a suitable desiccator or airtight container immediately upon removal and allowed to remain there until the temperature of the durometer is above the dew point of the air in the new environment. 7.2 Tests shall be carried out in one of the standard atmospheres specified in GB/T 2918-1998, unless otherwise stated in the relevant material specification.8 Procedure8.1 Place the test specimen on a hard, horizontal, plane surface. Hold the durometer in a vertical position with the point of the indenter (4.2) at least 9 mm from any edge of the test specimen. Apply the presser foot (4.1) to the test specimen as rapidly as possible, without shock, keeping the foot parallel to the surface of the test specimen. Apply just sufficient pressure to obtain firm contact between presser foot and test specimen. NOTE. Better reproducibility may be obtained by using either a durometer stand or a weight centred on the axis of the indenter, or both, to apply the presser foot to the test specimen. Recommended masses are 1 kg for the type A durometer and 5 kg for the type D durometer. Read the scale of the indicating device (4.3) after 15 s ± 1s. If an instantaneous reading is specified, read the scale within 1 s after the presser foot is in firm contact with the test specimen, unless the durometer has a maximum indicator, in which case the maximum reading shall be taken. 8.2 Make five measurements of hardness at different positions on the test specimen at least 6 mm apart and determine the mean value. NOTE. It is recommended that measurements be made with the type D durometer when values above 90 are obtained with the type A durometer and that measurements be made with the type A durometer when values less than 20 are obtained with the type D durometer.9 Test reportThe test report shall include the following particulars. a) a reference to this Standard; b) all details necessary for complete identification of the material tested; c) a description of the test specimen, including its thickness and, in the case of a composite test specimen, the number of layers; d) the temperature of test, and the relative humidity when the hardness of the material is dependent on the humidity; e) the type of durometer used (A or D); f) if known and if required, the time which elapsed between preparation of the test specimen and measurement of hardness; g) the individual values of the indentation hardness and the time-interval after which each reading was taken; NOTE. Readings may be reported in the form Shore hardness A/15.45, where A is the type of durometer, 15 is the time, in seconds, between bringing the pressure foot in firm contact with the test specimen and taking the reading, and 45 is the reading. Similarly, Shore hardness D/1.60 indicates a reading of 60 on the type D durometer obtained either within 1 s or from a maximum indication. h) the average value of the indentation hardness; i) details of any operations not specified in this Standard, as well as details of any incidents likely to have influenced the results. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 2411-2008 be delivered?Answer: The full copy PDF of English version of GB/T 2411-2008 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 2411-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 2411-2008_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 2411-2008 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 2411-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 2411-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 2411-2008?A step-by-step guide to download PDF of GB/T 2411-2008_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 2411-2008". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
