GB/T 22139-2008 English PDFUS$149.00 ยท In stock
Delivery: <= 2 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 22139-2008: Specification for film tension in 35mm motion-picture systems Status: Valid
Basic dataStandard ID: GB/T 22139-2008 (GB/T22139-2008)Description (Translated English): Specification for film tension in 35mm motion-picture systems Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: N42 Classification of International Standard: 37.060.10 Word Count Estimation: 5,542 Date of Issue: 2008-06-30 Date of Implementation: 2009-01-01 Adopted Standard: SMPTE RP 106-1994, MOD Regulation (derived from): Announcement of Newly Approved National Standards No. 11 of 2008 (No. 124 overall) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the 35 mm movie film with less than 0. 9m/s speed through the film transport system is running, to make the film needed to minimize damage to the movie tension. This standard recommends the film tension detection method. GB/T 22139-2008: Specification for film tension in 35mm motion-picture systems---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Specification for film tension in 35mm motion-picture systems ICS 37.060.10 N42 National Standards of People's Republic of China 35 m1 m1 Cinema System Specification film tension Posted 2008-06-30 2009-01-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis revised standard adopts SMPTERP106.1994 Movies "In less than 0.9m/s (180ft/min) running 35mm film system Sheet tension. " This standard and SMPTERP106. differences in 1994 is as follows. according to GB/T 1.1-2000 made editorial changes. The standard proposed by China Machinery Industry Federation. This standard is under the jurisdiction of movies and audio-visual industry machinery Machinery Standardization Technical Committee. This standard was drafted. Qinhuangdao Audio-Visual Machinery Research Institute. The main drafters of this standard. Yanji Hua. This standard is the first release.IntroductionThe machinery industry standard developed by the film and audio-visual machinery Standardization Technical Committee for the equipment manufacturer, to design and adjust new show Or running 35mm film projection equipment and film take-up device to provide guidance. When the current movie and sprocket wheel combination, videos Ultimate tensile fracture occurred before is 66.7N (15lbf). Therefore, all the take-up equipment must be kept in this film tension fracture limit tension The few hundred or less. Film tension exceeds 4.4N (16ozf) will increase the wear and tear of the film, is not necessary. When the tension of 1.7N (6ozf), the movie screen was enough to maintain stability. 35 m1 m1 Cinema System Specification film tension1 Scope1.1 standard specifies the 35mm movie film of less than 0.9m/s (3ft/s) speed run through the film transport system, in order to make the film loss Injury to a minimum required film tension. 1.2 standard detection method recommended by the film tension.2 Videos tensionUnder normal conditions the sprocket, the film tension should be 1.7N ~ 4.4N (6ozf ~ 16ozf) between.3 Detection3.1 0.9m ~ 1.8m (3ft ~ 6ft) film wound on the film holder tablet cores, or take-in sheet supply system operates in normal mode Case, dynamometer pull the film a measure. Tension shall be measured film winding diameter (die diameter) drawing tabulation, and Comply with the provisions in Chapter 2. 3.2 In order to measure the tension of the film, a short film will be screened sheet is placed inside the door, the door closed sheet, with a dynamometer pull the film through the film gate. NOTE. Adjust the film gate pressure, so that the screen is not more than beat 0.020mm. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 22139-2008_English be delivered?Answer: Upon your order, we will start to translate GB/T 22139-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 2 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 22139-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 22139-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
