GB/T 20801.2-2020 PDF EnglishUS$995.00 · In stock · Download in 9 seconds
GB/T 20801.2-2020: Pressure piping code - Industrial piping - Part 2: Materials Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 20801.2: Historical versions
Similar standardsGB/T 20801.2-2020: Pressure piping code - Industrial piping - Part 2: Materials---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT20801.2-2020GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 23.040 J 74 Replacing GB/T 20801.2-2006 Pressure piping code - Industrial piping - Part 2. Materials Issued on. NOVEMBER 19, 2020 Implemented on. JUNE 01, 2021 Issued by. State Administration for Market Regulation; Standardization Administration of PRC. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 9 4 General rules... 11 5 Basic principles of material selection... 13 6 Restrictions on the use of materials... 13 7 Restrictions on the use of materials under high temperature conditions... 21 8 Restrictions on the use of materials under low temperature conditions... 24 9 Material marking and quality certification... 34 Appendix A (Normative) Material designation and allowable stress... 36 Appendix B (Informative) Physical properties of materials... 72 Appendix C (Informative) Risk-based material design and selection... 78 Appendix D (Informative) Comparison of material standards and designations between China and foreign countries... 113 References... 1241 ScopeThis Part of GB/T 20801 specifies the basic requirements for materials for pressure piping components, including the selection of materials, restrictions on use based on material properties, marking and quality certification. This Part applies to the selection and use of materials, for pressure piping components, which are defined in the scope of GB/T 20801.1.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard. GB/T 229 Metallic materials - Charpy pendulum impact test method GB/T 1220 Stainless steel bars GB/T 1348 Spheroidal graphite iron castings GB/T 2882 Nickel and nickel alloys tube GB/T 3077 Alloy structure steels GB/T 3087 Seamless steel tubes for low and medium pressure boiler GB/T 3091 Welded steel pipes for low pressure liquid delivery GB/T 3098.1 Mechanical properties of fasteners - Bolts, screws and studs GB/T 3098.6 Mechanical properties of fasteners - Stainless steel bolts, screws and studs GB/T 3624 Titanium and titanium alloy seamless tubes GB/T 4334 Corrosion of metals and alloys - Test methods for intergranular corrosion of stainless steels GB/T 4437.1 Aluminium and aluminium alloy extruded tubes - Part 1. Seamless tubes GB/T 5310 Seamless steel tubes and pipes for high pressure boiler GB/T 6479 Seamless steel pipes for high-pressure fertilizer equipment GB/T 6614 Titanium and titanium alloy castings3 Terms and definitionsThe terms and definitions, as defined in GB/T 20801.1-2020, GB/T 20801.3- 2020, GB/T 20801.4-2020, GB/T 20801.5-2020, GB/T 20801.6-2020, as well as the following terms and definitions, apply to this document. 3.1 Low temperature and low stress service The working conditions, that need to meet the following conditions, at the same time. 3.2 Low temperature and lower stress service The working conditions that need to meet the following conditions, at the same time. 3.3 Electric-resistance welded pipe; ERW The pipe, which is continuously butt-welded, under the action of pressure, by the use of the pipe (coil) itself as the current loop, through electric resistance heating. 3.4 Electric-fusion welded pipe; EFW The pipe, which is longitudinally butt-welded on the preformed blank, by the use of automatic arc welding or manual arc welding. 3.5 Plate welded pipe An electrofusion welded pipe, is preformed from a flat plate into a tubular shape AND has one or two longitudinal straight welds. 3.6 Inspection certificate A form of material quality certification (inspection document). It is an inspection document, which is indicated of the results, by the independently authorized departments or personnel outside the production department of the manufacturer, after inspection and test on the delivered products (or sampling), according to the provisions of the standard and contract.4 General rules4.1 Material selection The owner or designer shall select appropriate materials for piping components, according to the specific use conditions (including manufacturing, fabrication and installation, media, operating conditions, working environment, testing, etc.) AND the material use requirements and restrictions specified in this Part, considering the risk of material damage. 4.2 Material and technical requirements 4.2.1 Table A.1 and Table A.2 of Appendix A specify the designations, allowable stress and application range of the piping component materials. The materials, which are used for the piping components, shall comply with the requirements of the material standards, as listed in Table A.1 and Table A.2. 4.2.2 In addition to the materials listed in Table A.1 and Table A.2, the following materials can be used for piping components; however, they shall meet the requirements and use restrictions for corresponding materials in this Part. 4.2.3 Materials with unknown designations shall not be used for piping components. 4.2.4 The recovered materials shall not be used in piping components. 4.2.5 The selection of other materials shall be subject to technical appraisal and review & approval, by institutions with corresponding qualifications.5 Basic principles of material selection5.1 The materials, which are used for pressure components (except bolts), shall have sufficient strength, plasticity, toughness. They shall have sufficient resistance to brittle fracture, at the lowest use temperature. When brittle materials, which have an elongation rate of less than 14%, are used, it shall take necessary safety protection measures. 5.2 The selected materials shall have sufficient stability, including chemical properties, physical properties, corrosion and wear resistance, fatigue resistance, organizational stability. 5.3 When selecting materials, it shall consider the applicability of the materials under possible open flames, fires and extinguishing conditions, as well as changes in material properties and secondary hazards, which are brought about by this. 5.4 The selected materials shall be suitable for the corresponding manufacturing, production, installation, including welding, cold and hot processing, heat treatment requirements. 5.5 When several different materials are used in combination, it shall consider the possible adverse effects. 5.6 Materials shall be available and economical.6 Restrictions on the use of materials6.1 Nodular cast iron, gray cast iron, malleable cast iron 6.1.1 Nodular cast iron 6.1.1.1 When nodular cast iron is used for piping components, its elongation shall not be less than 15%; the use temperature shall not be higher than 350 °C, but it shall be higher than -20 °C. The use restrictions of nodular cast iron piping components, which are listed in Table 13 of GB/T 20801.3-2020, shall comply with the corresponding requirements of GB/T 13295. 6.1.1.2 Except for GC3 grade pipes, nodular cast iron shall meet the impact performance requirements of GB/T 1348; the pressure rating shall not exceed 5.0 MPa. 6.1.2 Gray cast iron and malleable cast iron 6.1.2.1 When the gray cast iron and malleable cast iron, which are listed in Table A.1, are used for piping components, they shall meet the following requirements. 6.1.2.2 In addition to meeting the requirements of 6.1.2.1, the applicable pressure-temperature ratings of gray cast iron and malleable cast iron pipes, fittings, pipe flanges, valves shall also meet the requirements of the corresponding standards, in Table 13 of GB/T 20801.3-2020. 6.2 Carbon structural steel The restrictions on the use of carbon structural steel shall meet the following requirements. 6.3 Pipeline steel 6.3.1 Table A.1 includes carbon steel and pipeline steel pipes, butt-welded pipe fittings, flange forgings for long-distance pipelines including GB/T 9711, as shown in Table 2. 6.3.2 The product specification level (PSL) of pipeline steel shall meet the following requirements. 6.3.3 The minimum use temperature of PSL1 carbon steel, which is listed in 6.4 Pipes and butt-welded pipe fittings 6.5 Carbon steel and chromium-molybdenum alloy steel 6.6 Austenitic stainless steel 6.7 Plate-welded pipe 6.7.1 Plate-welded pipes shall be formed by longitudinal coils of steel plates, which have one or two longitudinal straight welds. Limited by the width of the steel plate, plate-welded pipes of larger diameter can be formed by lateral rolling the steel plates. 6.8 Aluminum and aluminum alloy 6.8.1 The mechanical properties of aluminum and aluminum alloys are related to thickness and delivery status. The properties and allowable stresses, which are listed in Table A.1, are only applicable to the specified range of the corresponding standards. 6.8.2 If the material standard does not specify the tensile and yield strength, this Part requires supplementation in the purchase contract. 6.8.3 The welding structure of the material, in the work-hardened state, shall adopt the allowable stress of the corresponding designation in the annealing state; the welding structure of the material, in the precipitation hardened state, shall adopt the allowable stress of the corresponding designation in the welding state. 6.9 Nickel and nickel alloys 6.9.1 The mechanical properties of nickel and nickel alloys are related to the processing and heat treatment conditions. The properties and allowable stresses, which are listed in Table A.1, are only applicable to the specified range of the corresponding standards. 6.10 Pipe support material 6.10.1 The standards, materials, allowable stresses, which are listed in Table A.1 and Table A.2, also apply to pipe supports. 6.10.2 The other requirements of the pipe support material shall be in accordance with the provisions of Chapter 8 of GB/T 20801.3-2020. 6.11 Low melting point metals7 Restrictions on the use of materials under high temperature conditions7.1 Upper limit of material's use temperature 7.1.1 Table A.1 and Table A.2 specify the upper limit of the material's use temperature, under normal circumstances. 7.1.2 When determining the upper limit of the use temperature of the material, it shall consider the influence of the medium and the environment. 7.2 Principles for the selection of high-temperature materials 7.2.1 General requirements 7.2.2 The use of carbon steel and chromium-molybdenum alloy steel under high temperature conditions 7.2.2.1 The high-temperature strength reduction factor W of welded joints, 7.2.3 The use of stainless steel under high temperature conditions 7.2.3.1 Under the high-temperature creep conditions (see 3.2 of GB/T 20801.3- 2020), the high-temperature strength reduction factor W of stainless steel welded joints shall be in accordance with the provisions of 4.2.7 in GB/T 20801.3-2020. 7.2.4 Use of other materials under high temperature conditions 7.2.4.1 Titanium and titanium alloys should not be used at temperatures above 316 °C.8 Restrictions on the use of materials under low temperature conditions8.1 Minimum use temperature and exemption of impact test 8.1.1 General provisions (except for cast iron) 8.1.1.1 In addition to the provisions of exempting the impact test in 8.1.1.4, 8.1.3, 8.1.4, 8.1.5, 8.1.6, the material and its welded joints shall be subjected to an impact test. 8.1.1.2 The impact test of the material and its welded joints shall be carried out, in accordance with 8.2. 8.1.1.3 When determining the minimum design temperature, it shall consider the fluid throttling effect and the influence of ambient temperature. 8.1.1.4 The carbon steel materials, which are used for GC3 grade pipelines, can be exempted from the impact test. 8.1.2 Cast iron The minimum use temperature of nodular cast iron, gray cast iron, malleable cast iron shall meet the requirements of 6.1. 8.1.3 Carbon steel, low temperature steel, chromium-molybdenum alloy steel, ferritic stainless steel, duplex stainless steel 8.1.3.1 The minimum use temperature and exemption conditions for impact test, 8.1.3.2 The welding procedure qualification of materials shall meet the requirements of Table 8, Table 11, Table 12. 8.1.4 Austenitic stainless steel 8.1.4.1 The minimum use temperature of austenitic stainless steel shall meet the requirements of Table A.1. 8.1.4.2 When the use temperature is lower than or equal to -20 °C, the austenitic stainless steel shall be subjected to the low temperature impact test. However, the low temperature impact test can be exempted, if the following requirements are met at the same time. 8.1.5 Nickel, nickel-based alloys, titanium alloys, aluminum alloys The minimum use temperature of nickel, titanium, aluminum and its alloys shall meet the requirements of Table A.1; the conditions for exempting impact test shall meet the requirements of Table 7. 8.1.6 Bolt material 8.2 Impact test 8.2.1 Impact test of base metal Except for the materials, which are exempted from the impact test in accordance with 8.1, the base metal shall be subjected to the impact test in accordance with the requirements of 8.2.3, 8.2.4, 8.2.5. 8.2.2 Impact test of welded joints The impact test of welded joints shall meet the following requirements. 8.2.4 Impact test temperature The impact test temperature shall meet the following requirements. 8.2.5 Qualification criteria The qualification criteria of the impact test shall be determined, in accordance with the following relevant requirements.9 Material marking and quality certification9.1 Material marking 9.1.1 The marking of materials shall comply with the requirements of the corresponding standards and contracts. 9.1.2 The content of the marking shall include at least the manufacturer's mark and the name of the material (code). The marking of the following piping components shall also include the furnace batch number or code of the material. a) Piping components for GC1 grade pipelines; b) The piping components subjected to the impact test according to the requirements of this Part; c) Chromium-molybdenum alloy steel (except bolt materials) piping components; 9.1.3 Materials shall be marked piece by piece. The markings shall be clear and firm. Materials, which have a nominal diameter less than or equal to DN40, can be marked with labels or other alternative methods. 9.2 Quality certification The quality certification of the material shall meet the following requirements. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 20801.2-2020 be delivered?Answer: The full copy PDF of English version of GB/T 20801.2-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 20801.2-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 20801.2-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 20801.2-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 20801.2-2020?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 20801.2-2020 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 20801.2-2020?A step-by-step guide to download PDF of GB/T 20801.2-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 20801.2-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
