GB/T 19568-2017 English PDFUS$439.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 19568-2017: Wind turbines -- Assembling and installation regulation Status: Valid GB/T 19568: Historical versions
Basic dataStandard ID: GB/T 19568-2017 (GB/T19568-2017)Description (Translated English): Wind turbines -- Assembling and installation regulation Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: F11 Classification of International Standard: 27.180 Word Count Estimation: 22,267 Date of Issue: 2017-12-29 Date of Implementation: 2018-07-01 Older Standard (superseded by this standard): GB/T 19568-2004 Regulation (derived from): National Standards Bulletin 2017 No. 32 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China GB/T 19568-2017: Wind turbines -- Assembling and installation regulation---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Wind turbines - Assembling and installation regulation ICS 27.180 F11 National Standards of People's Republic of China Replacing GB/T 19568-2004 Wind turbine assembly and installation specifications Windturbines-Assembling andinstallationregulation 2017-12-29 Posted 2018-07-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China China National Standardization Administration released Directory Preface Ⅰ 1 Scope 1 2 Normative references 1 3 assembly requirements4 Install 6 5 installation inspection 11 6 Quality Assurance 11 Appendix A (Normative) Secondary corrosion protection requirements 12 Appendix B (Normative) Large-scale wind turbine generator parts transport requirements 13 Appendix C (Informative) General connection bolt preload and tightening torque 14 Appendix D (Normative) Bolt tightness test method 17ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard replaces GB/T 19568-2004 "Wind Turbine Assembly and Installation Code." Compared with GB/T 19568-2004 main The technical changes are as follows. --- "Screws, bolted connections" to "screws, bolts, studs" (see 3.2.1,.2004 edition 3.2.1); --- Modify "Rolling bearing assembly" "Gearbox assembly" as "Spindle bearing assembly" "Assembly of main bearing and gearbox assembly" (see 3.3.1, 3.3.2,.2004 edition 3.3.1, 3.3.2); --- Increased the key components of yaw, pitch drive, brake, elastic support, hydraulic, lubrication system, cabin cover, hubcap assembly See (see 3.3.2, 3.3.3, 3.3.5, 3.3.8, 3.3.9, 3.3.10); --- Increased wind farm installation "wind turbine installation" "cable laying" and "electrical wiring" installation requirements (see 4.5.4, 4.5.5 and 4.5.7). This standard is proposed by the China Machinery Industry Federation. This standard by the National Wind Machinery Standardization Technical Committee (SAC/TC50) centralized. This standard was drafted by Shandong ZhongChang Wind Power Co., Ltd., Huaneng Renewable Energy Co., Ltd., China Electric Power Research Institute, Shenyang Engineering Industry University, Beijing Center for Certification and Accreditation Co., Ltd., China Guodian United Power Technology Co., Ltd., China Quality Certification Center, Beijing Tianyuanke Chuangfeng Electric Technology Co., Ltd. The main drafters of this standard. Li Guangwei, Wei East, Zhao Lei, Zhang Xiaochao, Wang Yin, Qin Shiyao, Liu Yingming, Yang Hongyuan, Hu Xuesong, Zhao Yu, Ning Qiao Zhen, Zhang Lei. This standard replaces the standards previously issued as. --- GB/T 19568-2004. Wind turbine assembly and installation specifications1 ScopeThis standard specifies the wind turbine assembly plant assembly and wind farm installation requirements, installation, installation inspection and quality assurance. This standard applies to wind turbine assembly and installation.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version applies to this article Pieces. For undated references, the latest edition (including all amendments) applies to this document. GB/T 19001 quality management system requirements GB/T 20319 wind turbine acceptance code GB/T 33628 wind turbine high strength bolt connection deputy installation technical requirements DL/T 796 wind farm safety regulations3 assembly requirements3.1 General requirements 3.1.1 All involved in the assembly of personnel should pass three safety education and job skills training. Special types of work (crane, special equipment) phase Should be the qualification certificate before induction. The key processes, special process operators trained qualified before induction. 3.1.2 Pre-assembly inspection All accessories models, specifications should meet the requirements of the configuration details. 3.1.3 pre-assembly inspection assembly parts into the assembly area should meet the following requirements before assembly. a) test qualified and with a mark of conformity; b) Review the main matching sizes and numbers of the key components required in the document and make a record in the warranty card; c) The fit size trimmed by fitter shall be re-inspected by the inspection department and recorded in the warranty card. 3.1.4 Each assembly process, there should be assembly records, and deposited into the wind turbine files. 3.1.5 parts should be cleaned and cleaned before assembly, there should be no burrs, burrs, scale, rust, chips, oil, coloring agents and dust Etc .; for sharp or high with the mating surface, before assembly should be amended; Unless otherwise specified, the assembly should be sharp corners and sharp edges before assembly blunt. Parts should not be knocked, bruised, scratched, and corroded during assembly. 3.1.6 Zero, parts in the assembly process secondary corrosion and different coating repair method in Appendix A. Paint wet parts can not be carried out assembly. 3.1.7 hoisting before lifting inspection rigging, rigging, lifting equipment, etc. should be consistent with the requirements of safety hoisting, hoisting may harm the location (Parts, slings) should be added protective pad. 3.1.8 measuring the workpiece measurement should be calibrated, and within the validity period. 3.1.9 equipment, special tools should be used before the operation of its status check, in the determination of no exception before use. 3.1.10 parts of the lubrication After the assembly process should be based on assembly instructions into the lubricating oil or grease. No special requirements, different models, no The same brand of oil, fat should not be mixed. 3.1.11 assembly work environment to meet the operational requirements. 3.1.12 Wind turbine large parts transport requirements, see Appendix B. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 19568-2017_English be delivered?Answer: Upon your order, we will start to translate GB/T 19568-2017_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 19568-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 19568-2017_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 19568-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 19568-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
