GB/T 1934.1-2009 English PDFUS$279.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 1934.1-2009: Method for determination of the water absorption of wood Status: Obsolete GB/T 1934.1: Historical versions
Basic dataStandard ID: GB/T 1934.1-2009 (GB/T1934.1-2009)Description (Translated English): Method for determination of the water absorption of wood Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: B60 Classification of International Standard: 79.020 Word Count Estimation: 6,617 Date of Issue: 2009-02-23 Date of Implementation: 2009-08-01 Older Standard (superseded by this standard): GB/T 1934.1-1991 Quoted Standard: GB/T 1928-2009; GB/T 1929-2009; GB/T 1931-2009 Regulation (derived from): National Standard Approval Announcement 2009 No.3 (Total No.143) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the determination of water absorption of the test timber equipment, specimens, test procedures and results of calculations. This section applies to a small sample timber unblemished water absorption. GB/T 1934.1-2009: Method for determination of the water absorption of wood---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Method for determination of the water absorption of wood ICS 79.020 B60 National Standards of People's Republic of China Replacing GB/T 1934.1-1991 Determination of water absorption of wood Posted 2009-02-23 2009-08-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordGB/T 1934 is divided into two parts. --- Determination of water absorption of wood; --- Wood Swelling of the measurement method. This section GB/T 1934.1 "Determination of water absorption of wood." This Part replaces GB/T 1934.1-1991 "Determination of water absorption of wood." This section compared with the GB/T 1934.1-1991 main changes are as follows. --- Principle revised as follows. "Wood is absorbent wood or water to saturation within the time prescribed quality water points, and the whole Dry wood mass ratio represented "; --- Remove 5.3 "allows the use of all-dry density was measured after the sample"; --- Increased flooding of the sample requirements of the 6.2 revised as follows. "The sample was pushed below the surface at least 50mm,"; --- Soaking time of 6.3 has been modified. Appendix A of this part is a normative appendix. This part by the State Forestry Administration. This part of the National Standardization Technical Committee centralized timber. This section is responsible for drafting units. China Forestry Science Institute of Wood Industry. This section participated in the drafting unit. China Forestry Research Institute of Forestry Institute for New Technologies, Northeast Forestry University. The main drafters of this section. ke Zhao, Huang Rongfeng, Lv Jianxiong, Zhaorong Jun, Fei Hua present, Yuhua Jiang, Huang Anmin, Liu Yingtao. This section was first released in 1980, the first revision in 1991, this is the second revision. This part of the National Standardization Technical Committee responsible for the interpretation of wood. Determination of water absorption of wood1 ScopeGB/T 1934 This section specifies the determination of the water-absorbent wood test equipment, samples, test procedures and results of calculations. This section applies to a small wood unblemished specimens measured water absorption.2 Normative referencesThe following documents contain provisions which, through reference to GB/T 1934 to the present, constitute provisions of this section. For dated reference documents Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section. GB/T 1928-2009 physical and mechanical test methods - General GB/T 1929-2009 physical and mechanical test materials and test specimens sawing method GB/T 1931-2009 Method for determination of moisture content of wood Principle 3 Wood is a porous organic material, with its ability to absorb moisture around. Wood is absorbent wood or water to saturation in Regulation The sub-quality water, and the whole mass of dry wood expressed as a ratio within a given time.4 Test Equipment4.1 container impregnated sample. 4.2 GB/T 1931-2009 test equipment specified in Chapter 3.5 Sample5.1 test material sawing and test specimens were according to GB/T 1929-2009 the provisions of Chapter 3. 5.2 Sample size is 20mm × 20mm × 20mm. Requirements and test specimens were made according to GB/T 1928-2009 the provisions of Chapter 3 get on.6 Test procedure6.1 The sample was placed in an oven starting temperature 60 ℃ for about 4h, then press GB/T 1931-2009 of 5.2 to 5.4 for drying And weigh (m1 0). 6.2 sample weighed, then placed in a container filled with distilled water inside, with a stainless steel wire mesh, pressed into the sample surface at least 50mm, cover Good container. The water temperature should be maintained within the range of (20 ± 2) ℃ for. 6.3 sample into the water for the first time after 6h weigh (m1), 1,2,4,8 days and nights later by weighing each time, until the moisture content of the last two When the difference is less than 5%, it can be considered to achieve maximum absorption. After soaking for 8 days and nights water content has not yet reached the required sample, according to Trend 7 results in water absorption curve calculation to determine the appropriate time interval measurements. Each time weighing, the samples were removed applications absorbent paper to absorb surface moisture from the container and then weighed. Distilled water should be kept within the container Clean, usually every 4 to 5 days and nights replacement.7 Results Calculation(1) shall be calculated absorption type 7.1 specimen to the nearest 1%. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 1934.1-2009_English be delivered?Answer: Upon your order, we will start to translate GB/T 1934.1-2009_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 1934.1-2009_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1934.1-2009_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 1934.1-2009?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1934.1-2009 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
