GB/T 18449.2-2012 English PDFUS$399.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 18449.2-2012: Metallic materials -- Knoop hardness test -- Part 2: Verification and calibration of testing machines Status: Valid GB/T 18449.2: Historical versions
Basic dataStandard ID: GB/T 18449.2-2012 (GB/T18449.2-2012)Description (Translated English): Metallic materials -- Knoop hardness test -- Part 2: Verification and calibration of testing machines Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: N71 Classification of International Standard: 19.060; 77.040.10 Word Count Estimation: 17,151 Older Standard (superseded by this standard): GB/T 18449.2-2001 Quoted Standard: GB/T 13634, GB/T 18449.1-2009, GB/T 18449.3 Adopted Standard: ISO 4545-2-2005, MOD Regulation (derived from): National Standards Bulletin No. 41 of 2012 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the Press GB/T 18449. 1-2009 Determination of Knoop hardness of metallic materials used in the test force range from 0. 09807N ~ 19. 614N Knoop hardness (hereinafter referred to as hardness) test and calibration methods. This secti GB/T 18449.2-2012: Metallic materials -- Knoop hardness test -- Part 2: Verification and calibration of testing machines---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. . Metallic materials Knoop hardness test Part 2. Verification and calibration of testing machines ICS 19.060; 77.040.10 N71 National Standards of People's Republic of China Replacing GB/T 18449.2-2001 Knoop hardness test of metallic materials Part 2. Verification and calibration of hardness Part 2. Verificationandcalibrationoftestingmachines (ISO 4545-2.2005, MOD) Issued on. 2012-12-31 2013-06-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ 1 Scope 1 2 Normative references 1 3 General requirements 1 4 direct examination 1 5 indirect test 3 6 inspection cycle 4 7 inspection reports and (or) calibration certificate 5 Appendix A (informative) Explanation on diamond indenter 6 Annex B (informative) durometer calibration measurement uncertainty 7ForewordGB/T 18449 "Knoop hardness test of metallic materials" is divided into four parts. --- Part 1. Test methods; --- Part 2. Verification and calibration of hardness; --- Part 3. Calibration of hardness reference blocks; --- Part 4. Tables of hardness values. This section GB/T 18449 Part 2. This section drafted in accordance with GB/T 1.1-2009 given rules. This Part replaces GB/T 18449.2-2001 "metal Knoop hardness test - Part 2. hardness test", and GB/T 18449.2-2001 compared to the main technical changes are as follows. --- Modify the name; --- Remove the ISO foreword (version 2001 ISO foreword); --- Increasing the test force range (see Chapter 1, Chapter 1 of the 2001 edition); --- Increasing the reference standard GB/T 13634-2008 "uniaxial testing machines standard dynamometer calibration" (see Chapter 2); --- Increasing the test temperature, test and calibration instruments traceability indenter constant testing cycle, indirect measurement calibration test blocks On the reference indentation hardness showed the relative repeatability and indication of the relative error is calculated (see 4.1.1,4.1.2,4.3.5, 4.5,5.1,5.2,5.7,5.8); --- Modify the test force tolerance indicators and representation, diamond pyramid opposite edge angle β between tolerance indices (see Table 1,4.3.4, 2001 Edition 4.1.4,4.2.3); --- Modify the durometer value Index repeatability and hardness indication error (see Table 2 and 5.8,2001 version 5.2.2 and Table 1); --- Adjust the standard configuration (see Chapter 4, Chapter 5, 2001 edition of Chapter 4, Chapter 5); --- Increasing the specified testing period (see Chapter 6); --- Increase the informative Appendix A "diamond indenter on the instructions"; --- Increase the informative Appendix B "durometer calibration measurement uncertainty." This section uses redrafted law revision of international standards ISO 4545-2. "Part 2 of metallic materials Knoop hardness test 2005 Score. hardness testing and calibration "(first edition). In the text structure and technical content 4545-2 and ISO .2005 agreement. This part of ISO 4545-2.2005 and the technical differences for the following reasons. --- Remove the ISO 4545-2.2005 foreword, preface rewritten; Inside --- on normative references, this part of the technical differences have been adjusted in order to adapt to China's technical conditions, adjustment Yung focus reflected in Chapter 2, "Normative references", the specific adjustments are as follows. ● equivalents adoption of international standards GB/T 13634 replaced by ISO 376 (see 4.2.2); ● Modify with international standards of GB/T 18449.1-2009 instead of ISO 4545-1.2005 (see Chapter 1, 4.2.1, 4.3.5,4.5,5.5 and Appendix B); ● Modify with international standards of GB/T 18449.3 instead of ISO 4545-3.2005 (see 5.1); --- Corrected Table B.1 in Appendix B, Table B.3, table B.4, B.8 and Table Table B.5 some incorrect calculation results and data, and Done to correct place marked with an underscore; --- Regulate the expression of some methods of calculation formula in Appendix B to the formula in substitution values; --- Appendix B of the formula (B.10), formula (B.13) and Table B.9 the symbol "b" is replaced with the symbol "E"; --- Deleted references. This part of ISO 4545-2.2005 as compared to the existence of technical differences between the terms of these differences has been involved through its outer margins A single vertical line (︱) positions were marked. This section also made the following editorial changes. --- The "this part of ISO 4545" replaced by "this section"; --- With Chinese decimal symbol "." Decimal symbol instead of the English "." Please note that some of the content of this document may involve patents. Release mechanism of the present document does not assume responsibility for the identification of these patents. This part is proposed by China Machinery Industry Federation. This part of the National Technical Committee of Standardization Testing Machine (SAC/TC122) centralized. This section is drafted. Quanzhou Donghai instrument hardness block factory, Changchun Research Institute of Machinery Co., Ltd., Haitai Ming optical instruments Co., Ltd, Shanghai Measurement and Testing Technology Research Institute, Laizhou Huayin Test Instrument Co., Ltd., Shenzhen City, measuring Detection Technology Co. Shares the company. The main drafters of this section. Lisong Mao, Yuan Song, Choi Ma Liang, Yu Weiliang, Chen Zhiming, Zhouqiao Yun, Zhu Ping. This part of the standard replaces the previous editions. --- GB/T 18449.2-2001. Knoop hardness test of metallic materials Part 2. Verification and calibration of hardness1 ScopeThis section GB/T 18449 specifies the press GB/T 18449.1-2009 Determination of metallic materials with Knoop hardness test force range from 0.09807N ~ 19.614N Knoop hardness (hereinafter referred to as hardness) test and calibration methods. This section applies only to long diagonal Line length not less than 0.020mm indentation. This section applies to the basic functions of checking hardness test and inspection directly durometer overall performance of the indirect test. Indirect Inspection Method can be used independently for use in hardness regular routine checks. If the durometer hardness test is also used other methods, respectively, for each type of method should be individually hardness tested.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 13634 uniaxial testing machines standard dynamometer calibration (GB/T 13634-2008, ISO 376.2004, Metalic materials-Calibrationofforce-provinginstrumentsusedfortheverificationofuniaxialtestingma- chines, IDT) Test Method. GB/T 18449.1-2009 metallic materials - Knoop hardness test - Part 1 (ISO 4545-1.2005, MOD) GB/T 18449.3 metallic materials Knoop hardness test - Part 3. Calibration standard hardness block (GB/T 18449.3- 2012, ISO 4545-3.2005, MOD)3 General requirementsIn the hardness test before, should be checked to ensure that the hardness according to the manufacturer's instructions to properly install, and special check. a) a spindle head can slide freely without any friction or obvious gap; b) pressure head fixedly mounted on the spindle; c) upon application and removal of the test force, no shock or vibration does not affect the reading; d) For the measuring device and the host as one of hardness. --- From the application and removal of test force the state to the measurement state conversion process does not affect the reading; --- Lighting does not affect the reading; --- Indentation center is located near the center of the field.4 direct examination4.1 General 4.1.1 Direct test should be in the temperature range of (23 ± 5) ℃ were. If testing outside of this temperature range, the test should be reported The report noted. 4.1.2 appliance for testing and calibration should be traceable to national benchmarks. 4.1.3 Direct test include. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 18449.2-2012_English be delivered?Answer: Upon your order, we will start to translate GB/T 18449.2-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 18449.2-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18449.2-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 18449.2-2012?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 18449.2-2012 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
