GB/T 18250-2015 PDF EnglishUS$130.00 · In stock · Download in 9 seconds
GB/T 18250-2015: Graduations and test method for performance of deformation between stories of curtain wall Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 18250: Historical versions
Similar standardsGB/T 18250-2015: Graduations and test method for performance of deformation between stories of curtain wall---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT18250-2015 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 91.060.10 P 32 Replacing GB/T 18250-2000 Graduations and test method for performance of deformation between stories of curtain wall Issued on: OCTOBER 9, 2015 Implemented on: SEPTEMBER 1, 2016 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration Committee. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions ... 5 4 Graduations ... 7 5 General provisions ... 8 6 Inspection principle ... 8 7 Testing equipment ... 8 8 Loading method ... 10 9 Specimen and mounting requirements ... 11 10 Testing steps ... 12 11 Testing results and assessment ... 16 12 Testing report ... 17 Annex A (Informative) Test method for deformation performance combined direction of curtain wall ... 19ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard replaces GB/T 18250-2000 Test method for performance in plane deformation of curtain walls. Compared with GB/T 18250-2000, the main technical modifications in this Standard are as follows. - provided the definition of deformation performance of curtain wall (see 3.2); - added the graduations for performance of deformation between stories of curtain wall (see Clause 4); - added the outer plane (Y axis dimension) and vertical direction (Z axis dimension) deformation performance and test method (see 10.3, 10.4); - added the test method for displacement performance between stories of curtain wall (see Annex A). This Standard was proposed by Ministry of Housing and Urban-Rural Development of the People's Republic of China. This Standard shall be under the jurisdiction of National Technical Committee on Building Facades Windows and Doors of Standardization Administration of China (SAC/TC 448). The drafting organizations of this Standard. China Academy of Building Research, China Construction Metal Structure Association, Guangdong Provincial Institute of Building Science, Shenyang Yuanda Aluminum Engineering Co., Ltd., Guangzhou Aluminum Decoration Engineering Co., Ltd., Beijing Industry University, Shanghai Institute of Building Science (Group) Co., Ltd., Shandong Provincial Institute of Building Science, Guangdong Kennedy Lang Hardware Products Co., Ltd., Guangzhou City Building Science Research Institute Co., Ltd., Shanghai Construction Supervision Co., Ltd., Zhongshan Shengxing Co., Ltd., Shenzhen Shenye Tailan Construction Engineering Co., Ltd., Henan Construction Science Research Institute Co., Ltd., Hebei Austrian Run Shunda Window Industry Co., Ltd., Tianjin Jin Bell Construction Engineering Testing Technology Co., Ltd., Zhejiang New Century Engineering Inspection Co., Ltd., Tianjin Jianke Building Energy-saving Environmental Testing Co., Ltd., Ningbo and State Testing Research Limited, Hubei Product Quality Supervision and Inspection Research Institute, China Building Materials Inspection and Certification Center, Jangho Curtain Wall Co., Ltd., Shanghai Timalco Curtain Wall Engineering Technology Co., LTD. Graduations and test method for performance of deformation between stories of curtain wall1 ScopeThis Standard specifies the terms and definitions, graduations, general provisions, inspection principle, testing equipment, loading method, specimen and mounting requirements, testing steps, test results and assessment and testing report for performance of deformation between stories of curtain wall. This Standard is applicable to grading testing and engineering testing for performance of deformation between stories of curtain wall.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 15227, Test method of air permeability, water tightness, wind load resistance performance for curtain walls GB 50011, Code for seismic design of buildings JGJ/T 97, Standard for terminology in earthquake engineering3 Terms and definitionsFor the purposes of this document, the terms and definitions defined in GB 50011, JGJ/T 97 and the following ones apply. 3.1 deformation between stories relative displacement between two adjacent building stories at horizontal direction (X axis), out plane horizontal direction (Y-axis, perpendicular to X-axis direction) and vertical direction (Z-axis) within the curtain wall plane under the effects of earthquake, wind load, etc.; X axis, Y axis, Z axis directions are shown in Figure 1. parts from damage and dysfunction when the story is repeatedly displaced in the Y-axis dimension 3.6 deformation performance vertical direction of curtain wall curtain wall Z-axis dimension deformation performance the ability that the curtain wall maintains its own and the main connection parts from damage and dysfunction when the story is repeatedly displaced in the Z-axis dimension 3.7 deformation performance combined direction of curtain wall the ability that the curtain wall maintains its own and the main connection parts from damage and dysfunction when the story, in the X-axis, Y-axis, Z-axis dimensions, simultaneously produces two or three dimensions of the repeated displacements 3.8 drift angle between stories the ratio of the inter-story displacement value to the height of the story along with X-axis, Y-axis dimension directions 3.9 vertical displacement between stories the height change between adjacent stories along with Z-axis dimension direction4 Graduations4.1 Graduation indexes 4.1.1 The deformation performance in plane of curtain wall shall take the drift angle between stories of X-axis dimension direction as graduation index value, in γx. 4.1.2 The deformation performance out plane of curtain wall shall take the drift angle between stories of Y-axis dimension direction as graduation index value, in γy. 4.1.3 The deformation performance vertical direction of curtain wall shall take the vertical displacement between stories of Z-axis dimension direction as graduation index value, in δz. 4.2 Graduations for performance of deformation between stories of curtain wall The graduations for performance of deformation between stories of curtain 9.1.6 The point support curtain wall specimen shall have at least four glass plates and a complete cross seam same with the actual construction. The support structure shall have at least one typical bearing unit. The point support curtain wall which uses glass rib support shall comply with the provisions of full glass curtain wall simultaneously. 9.2 Mounting requirements The mounting of the specimen shall meet the design requirements. No special attachments or other measures shall be taken. The assembly, mounting method and force of specimen shall be in accordance with the actual conditions. The specimen shall be mounted on a fixed beam or movable beam according to the actual connection method. The fixed beam or movable beam shall be mounted on the mounting bracket.10 Testing steps10.1 Preparation before testing 10.1.1 The specimen shall be inspected after mounting. After the inspection is completed, the openable part of the specimen shall be switched off five times then fastened up. 10.1.2 Inspect that the pendulum or movable beam is not constrained in the range along the displacement direction. At the same time, there shall be a corresponding limit measure outside the range so as to ensure that the pendulum or movable beam does not produce displacement in any other direction. 10.1.3 Mount the test static loader according to the selected loading method. The arrangement of the loading device should be reasonable so as to ensure the effectiveness of the displacement produced. 10.2 X-axis dimension deformation testing 10.2.1 Mounting displacement measuring device Mount the displacement measuring device at the bottom of the swing lever or at the end of the movable beam. And make the displacement measuring device in normal operation. At the same time, the displacement measuring device can be added to the side of curtain wall component at the connection corner connector of the curtain wall specimen and the movable beam. X-axis dimensional deformation performance displacement measurement device mounting is shown in Figure 5. H - story height, in millimeters (mm); δx - X-axis dimension direction horizontal displacement absolute v... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 18250-2015 be delivered?Answer: The full copy PDF of English version of GB/T 18250-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 18250-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18250-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 18250-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 18250-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 18250-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 18250-2015?A step-by-step guide to download PDF of GB/T 18250-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 18250-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
