GB/T 18230.3-2000 PDF EnglishUS$85.00 · In stock · Download in 9 seconds
GB/T 18230.3-2000: Hexagon nuts for high-strength structural bolting with large width across flats - Product grade B - Property classes 8 and 10 Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Obsolete
Similar standardsGB/T 18230.3-2000: Hexagon nuts for high-strength structural bolting with large width across flats - Product grade B - Property classes 8 and 10---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT18230.3-2000 GB National Standard of the People’s Republic of China Hexagon nuts for high-strength structural bolting with large width across flats - Product grade B - Property classes 8 and 10 Issued on: OCTOBER 17, 2000 Implemented on: MAY 01, 2001 Issued by. the State Bureau of Quality Technical Supervision Table of ContentsForeword ... 3 ISO Foreword ... 4 1 Scope ... 5 2 Normative references... 5 3 Dimensions ... 6 4 Technical conditions and quoted standards ... 7 5 Zinc-galvanized fasteners shall be painted with lubricant agent ... 8 6 Proof load ... 8 7 Labeling ... 8 8 Marking ... 9 Annex A ... 10 Annex B ... 11ForewordThis Standard equivalently adopts international standard ISO 4775.1984 Hexagon Nuts for High-Strength Structural Bolting with Large Width Across Flats - Product Grade B - Property Classes 8 and 10. This Standard specifies the packaging technical requirements which is not specified in ISO 4775. ISO 4775 does not quote ISO 225 Fasteners - Bolts, Screws, Studs and Nuts - Symbols and Designations of Dimensions and ISO 8992 Fasteners - General Requirements for Bolts, Screws, Studs and Nuts. This Standard amends the provisions (see Chapter 3 note and Table 2) according to the latest relevant ISO fasteners standard (such as ISO 8673.1999 Hexagon Nuts, Style 1, with Metric Fine Pitch Thread - Product Grades A and B. This Standard adds provisions of filtration of zinc powder which is not specified in ISO 4775. This Standard specifies 6AX thread extreme dimension (see Appendix A) according to ISO 965-5.1998 General Purpose Metric Screw Threads - Tolerances – Part 5. Limits of Sizes of Internal Screw Threads, to Mate with Hot-Dip Galvanized External Screw, Threads with Maximum Size of Tolerance Position H before being Galvanized. Annex A and B are normative. This Standard was proposed by State Administration of Machinery Industry. This Standard shall be under the jurisdiction of National Technical Committee for Auto Standardization. Responsible drafting organization. Academy of Machinery Science and Technology. Participating drafting organizations. Shanghai Jinma High Strength Fastener Co., Ltd, Shanghai High-strength Bolts Plant, Shanghai Shenguang High-strength Bolts Plant, Zhejiang Shaoxing High Strength Fastener Plant, and Hebei Ren County High-strength Bolts Co. Ltd.ISO ForewordISO (International Standardization Organization) is a syndicate consisting of state standard group (members of ISO) across the world. The formulation of the international standard is made by all technical committees of ISO. Each member who is interested in projects of certain technical committee can participate in the committee. Governmental and non-governmental international organizations related with ISO can also take part in the job. ISO is closely related with IEC in terms of electro-technical normalization. International standard draft adopted by technical committee shall be distributed to all member groups for voting. The official publication of international standards needs at least 75% votes by the member groups. International standard ISO 4775 was formulated by ISO/TC 2 Fasteners Technical Committee. Hexagon nuts for high-strength structural bolting with large width across flats - Product grade B - Property classes 8 and 101 ScopeThis Standard specifies the hexagon nuts for structural bolting - thread specification is M12-M36, the performance grades are 8 and 10, the product grade is B, and used with grades 8.8 and 10.9 bolts. Other technical requirements shall be selected from current standards (such as GB/T196, GB/T197 and GB/T3098.2). The nuts specified in this Standard shall be matched with appropriate bolts (such as GB/T18230.1 or GB/T18230.2), so as to effectively prevent the connectors from thread tripping due to over-twisting. Hot-dipped galvanized nuts can provide 6H thread tolerance zone after galvanization according to the agreement by the supplier and purchaser. 6H hot-dipped galvanized nuts must be matched with 8.8s U or 10.9s U hot-dipped galvanized bolts, and thread tripping may occur due to over-twisting. Note. please make sure correctly using bolt for satisfactory results. For the purpose of proper use, it is recommended to formulate supplementary specifications for bolt connection.2 Normative referencesThe provisions contained in the following standards become part of this Standard, through the reference of this Standard. At the time of publication of this Standard, the shown versions of these standards are valid. All standards are subject to revision, and all parties who use this Standard are encouraged to investigate the possibility of applying the newest version of these standards. GB/T 90-1985 Acceptance check, marking and packaging of fasteners (eqv ISO 3269.1984) GB/T 196-1981 Basic Size of Common thread (Diameter of 1~600 mm). GB/T 197-1981 Tolerance and coordination of normal thread (Diameter of 1~355 mm). GB/T 1237-2000 Marking method of fasteners (eqv ISO 8991.1986) GB/T 3098.2-2000 Mechanical performance of fasteners nuts and coarse threads (idt ISO 898-2.1992) GB/T 3103.1-1982 Tolerances for Fasteners Bolt, Screw and Nut (eqv ISO 4759-1.1978) GB/T 5267-1985 Electroplated Coating of Threaded Fastener GB/T 5276-1985 Dimension number and mark of fasteners, bolts, nail, double-screw bolt and nut (eqv ISO 225.1983) GB/T 13912-1992 Hot Dip Electroplated Coating Technical Requirements of Steel Products with Metal coating (neq ISO 1459.1973) GB/T 16938-1997 General Technical Requirements for Fasteners, Bolts, Screws, Studs and Nuts (idt ISO 8992.1986) GB/T 18230.1-2000 The length grades of the thread of Hexagon cap bolts for structural bolting are 3106 and 10.9 in Level C of GB/T3106 (eqv ISO 7411.1984) GB/T 18230-2000 Hexagon cap bolts for structural bolting length of thread are grade 8 and 10.9 in Level C of GB/T3106 (eqv ISO 7412.1984) GB/T 18230-2000 Bolted structure is quenched and tempered with flat washer (neq ISO 7416.1984) JB/T 5067-1999 Iron and steel parts zinc power impregnation3 DimensionsNote. the dimension code and mark shall meet the provisions of GB/T 5276. Figure 1 Table 11) Dimensions mm Thread specification D M122) M16 M20 (M22)3) M24 (M27)3) M30 M36 p4) 1.75 2 2.5 2.5 3 3 3.5 4 da max 13 17. 3 21.6 23.8 25.9 29.1 32.4 38.9 min 12 16 20 22 24 27 30 36 dw max 5) 5) 5) 5) 5) 5) 5) 5) Available types ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 18230.3-2000 be delivered?Answer: The full copy PDF of English version of GB/T 18230.3-2000 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 18230.3-2000_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18230.3-2000_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 18230.3-2000 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 18230.3-2000?A step-by-step guide to download PDF of GB/T 18230.3-2000_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 18230.3-2000". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
