GB/T 17587.3-2017 PDF EnglishUS$150.00 · In stock · Download in 9 seconds
GB/T 17587.3-2017: Ball screws -- Part 3: Acceptance conditions and acceptance tests Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 17587.3: Historical versions
Similar standardsGB/T 17587.3-2017: Ball screws -- Part 3: Acceptance conditions and acceptance tests---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT17587.3-2017GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 25.040.20 J 51 Replacing GB/T 17587.3-1998 Ball screws – Part 3. Acceptance conditions and acceptance tests (ISO 3408-3.2006, MOD) Issued on: SEPTEMBER 29, 2017 Implemented on: APRIL 01, 2018 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 7 2 Normative references ... 7 3 Terms and definitions ... 7 4 Acceptance conditions and permissible deviation ... 8 4.1 Classification ... 8 4.2 Geometric accuracy test ... 8 4.2.1 Tolerance ... 8 4.2.2 Assessment of measurement drawing ... 9 5 Acceptance test ... 11 5.1 Overview ... 11 5.2 Travel deviation and variation ... 14 5.3 Run-out and orientation tolerances ... 19 5.4 Performance test ... 29 Appendix A (Normative) Supplementary forms ... 31ForewordGB/T 17587 “Ball screw” is divided into the following five parts. - Part 1. Vocabulary and designation; - Part 2. Nominal diameters and nominal leads - Metric series; - Part 3. Acceptance conditions and acceptance tests; - Part 4. Static axial rigidity; - Part 5. Static and dynamic load ratings and operational life. This part is part 3 of GB/T 17587. This part was drafted in accordance with the rules given in GB/T 1.1-2009. This part replaces GB/T 17587.3-1998 “Ball screws - Part 3. Acceptance conditions and acceptance tests”. As compared with GB/T 17587.3-1998, the main technical changes are as follows. - In the “4.1 classification”, CHANGE the 7 standard tolerance grades into 8 standard tolerance grades, ADD the standard tolerance grade 0 in Table 1. Thereafter any part related to the standard tolerance grade and test item permissible deviation will be added with the standard tolerance grade 0 and the corresponding permissible deviation; - In “4.2.1 Tolerance”, ADD the calculation formula of the travel variation tolerance vup within the useful travel of the grade 0 accuracy; - CHANGE the “4.2.2 Travel deviation” of 1998 version into “5.1 Overview”; ADD a new table in clause 5.1; CHANGE the Table 2 of the 1998 version into Table 3; - CHANGE the “4.2.3 Calculation of measurement drawings” of the 1998 version into “4.2.2 Assessment of measurement drawings”; ADD “4.2.2.1 Overview”; CHANGE the original 4.2.3.1 and 4.2.3.2 into 4.2.2.2 and 4.2.2.3; - MODIFY the Figure 2 in clause 5.1. CHANGE the “permissible deviation =” into “permissible deviation ≤”. ADD the figures and guide line 4 indicating the travel measuring device which is lacked in the original Figure; - MODIFY the clause 5.1, 5.2 and 5.3, respectively, of the 1998 version into 5.2, 5.3 and 5.4; DELETE the Table 3, Table 4 and Table 5 in the 1998 version which are shared by many items into one table for each test item; - CHANGE the “Mean travel deviation e” in the test item E1.1 and E1.2 of the 1998 version into the “Mean travel deviation esa and e0a” AND the “Mean travel deviation e0a” in the test item E1.2; - MODIFY the test formula of the permissible deviation in the test item E1.2; - In the inspection descriptions of the test item E4, ADD that “the letter n in the diagram represents the number of rotations of the ball screw as corresponding to the ball nut”; - CHANGE the test item E6, E7, and E8 of the 1998 version, respectively, into E6.1, E7.1 and E8.1; ADD the test item E6.2, E7.2, and E8.2; in the diagram of E8.1, ADD the indicator and the formula to assess the inspection results; - DIVIDE the permissible deviation column of the test item E12 into two conditions. lu ≤ 4000 mm and lu > 4000 mm; ADD the permissible deviation lu > 4000 mm; DELETE the notes on lu > 3000 mm in the permissible deviation column of the 1998 version; CHANGE the “Ball screw (both ends without seals)” in the inspection descriptions of the 1998 version into “Ball screw (both ends with/without seals)”; - MODIFY the title and the “Tolerance on specified travel” in the Table A.1 of Appendix A into “The tolerance value within the specified travel”; - MODIFY the Table A.3 in Appendix A; DELETE the note below the original table. This part, through the redrafting methods, modifies and adopts ISO 3408- 3.2006 “Ball Screws - Part 3. Acceptance conditions and acceptance test”. As compared with ISO 3408-3.2006, the main technical differences and the reasons of this part are as follows. - In ISO 3408-3.2006, the ball screw standard tolerance grade does not have grade 2 and grade 4. Considering that the grade 2 and grade 4 ball screw is widely used in China, so in the Table 1 of the “4.1 Classification” in this part, it retains the treatment method in GB/T 17587.1-1998, adds the standard tolerance grade 2 and grade 4, after which once the standard tolerance grade and test item permissible deviation, the grade 2 and grade 4 standard tolerance grade and the corresponding permissible deviation are added; - In “4.2.1 Tolerance”, same as GB/T 17587.1-1998, ADD the calculation formula of the travel variation vup within the grade 2 and grade 4 accuracy useful travel; - MAKE the following changes of the Figure 2 in clause 5.1. CHANGE the “permissible deviation =” into “permissible deviation ≤”; ADD the figure indicating the travel measuring device; INDICATE its guide line 4 again; - In the test descriptions of the test item E4, ADD that “the letter n in the diagram represents the number of rotations of the ball screw as corresponding to the ball nut”; - In the test item E5, same as GB/T 17587.1-1998, in note 1, ADD that “at this time l1 is the ball screw shaft total length”; - In the test items E6.1, E7.1 and E8.1, same as in E6, E7 and E8 in GB/T 17587.1-1998, ADD the note to the table that “it is agreed to allow the ball screw shaft top to be measured at the center hole”; - In Appendix A, taking into account the ball screw of nominal lead 4, 6, 8, 12, 16 ... is widely used, same as the Table A.2 in GB/T 17587.1-1998, ADD the specifications of the nominal lead, CHANGE the “Lead” in the table into “Nominal lead”, CHANGE “Ph” into “Ph0”; - In Table A.3 of Appendix A, taking into account that the specification of nominal lead is modified in Table A.2, the original Table A.3 is modified accordingly. This part makes the following editorial changes of ISO 3408-3.2006. - In the “4.2.1 Tolerance” and the note to Table A.1 in Appendix A, for the determination method of the tolerance on specified travel ep in the useful travel, CHANGE it from the descriptions without differentiating the accuracy grade into the descriptions based on grade 0 accuracy and based on other accuracy grades; - MOVE the note to the arrow below the esa and e0a of Figure 3b) in clause 4.2.2.3 of ISO 3408-3.2006 to the center line between the l'2 and l2; - MODIFY the symbol “v2πp” in the test item E4 of 5.2 in ISO 3408-3.2006 to “v2π”. This part was proposed by China Machinery Industry Federation. This part shall be under the jurisdiction of the National Standardization Technical Committee on Metal Cutting Machine (SAC/TC 22). The drafting organizations of this part. Jiangsu Rui’an Special Machinery Group Co., Ltd., Beijing Machine Tool Research Institute, China Machine Tool Quality Supervision and Inspection Center, Nanjing Technology and Equipment Ball screws – Part 3. Acceptance conditions and acceptance tests1 ScopeThis part of GB/T 17587 specifies the technical acceptance conditions for ball screws (SEE Figure 1), in particular, the respective permissible deviations for the acceptance tests. Note. The actual structure need not necessarily be consistent with the structure shown in Figure 1. The required test items shall be agreed upon by the manufacturer and user. This part applies to machine tool ball screw, the other can also make reference to it.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this standard. GB/T 1800.1-2009 Geometrical product specifications (GPS) - Limits and fits - Part 1. Bases of tolerances deviations and fits (ISO 286-1.1988, MOD) GB/T 17421.1-1998 Test code for machine tools - Part 1. Geometric accuracy of machines operating under no-load or finishing conditions (eqv ISO230-1.1996) GB/T 17587.1-2017 Ball screws - Part 1. Vocabulary and designation (ISO 3408-1.2006, MOD)3 Terms and definitionsThe terms and definitions as defined in GB/T 17587.1-2017 apply to this document. Where. ea - Actual mean travel deviation as relative to the specified travel or the nominal travel; γ - The angle of rotation of the ball nut as relative to the ball screw shaft (specified travel or nominal travel, as appropriate); γi - The angle of rotation of i-th measurement point (it can also be as relative to the specified travel or nominal travel, as appropriate, of the i-th measurement point); ei - Travel deviation of the specified travel or nominal travel corresponding to the i-th measurement point; n - The number of measurement points. 4.2.2.3 Graphic method [SEE Figure 3a) and Figure 3b)] The method of determining the actual mean travel deviation based on the actual travel deviation is as follows. a) MAKE tangents (l1, l2, ...) passing through two or more upper peak points on the actual travel deviation curve; MAKE tangents (l3, ...) passing through the lower peak point; b) DETERMINE each maximum deviation values (e1, e2, e3, ...) parallel to the ... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 17587.3-2017 be delivered?Answer: The full copy PDF of English version of GB/T 17587.3-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 17587.3-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 17587.3-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 17587.3-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 17587.3-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 17587.3-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 17587.3-2017?A step-by-step guide to download PDF of GB/T 17587.3-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 17587.3-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
