GB/T 1443-2016 English PDFUS$219.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 1443-2016: Self-holding tapers for machine tools and tool shanks Status: Valid GB/T 1443: Historical versions
Basic dataStandard ID: GB/T 1443-2016 (GB/T1443-2016)Description (Translated English): Self-holding tapers for machine tools and tool shanks Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J41 Classification of International Standard: 25.140.30 Word Count Estimation: 11,165 Date of Issue: 2016-02-24 Date of Implementation: 2016-09-01 Older Standard (superseded by this standard): GB/T 1443-1996 Quoted Standard: GB/T 11334 Adopted Standard: ISO 296-1991, MOD Regulation (derived from): National Standard Announcement No Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China GB/T 1443-2016: Self-holding tapers for machine tools and tool shanks---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Self-holding tapers for machine tools and tool shanks ICS 25.100.01 J41 National Standards of People's Republic of China Replacing GB/T 1443-1996 Machine tools and tool handles with a clip from the cone (ISO 296.1991, MOD) Issued on. 2016-02-24 2016-09-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. This standard replaces GB/T 1443-1996 "machine tools and tool handles with clip from the cone." This standard and GB/T 1443-1996 compared to the main changes are as follows. --- Modify the normative references; --- Note to the table in Table 1 in the segment table; --- Increased by 1, Note 2 of FIG; --- Cone tolerances and order type and size of the swap; --- Added Appendix A. This standard uses redrafted law revision using ISO 296.1991 "Machine tool shank with self-locking cone." This standard and ISO 296.1991 compared to the existence of technical differences, Appendix A gives the list of the corresponding technical differences and their causes. This standard and ISO 296.1991 compared also made the following editorial changes. --- International standards in Figures 1 and 2 of this standard spin-off of Figure 1, Figure 2, Figure 3, Figure 4 statements. The standard proposed by China Machinery Industry Federation. This standard tool by the National Standardization Technical Committee (SAC/TC91) centralized. This standard is drafted by. Chengdu Tool Research Institute Limited. The main drafters of this standard. Yu Zeng ring, Chen Shichang. This standard replaces the standards previously issued as follows. --- GB 1443-1985, GB/T 1443-1996. Machine tools and tool handles with a clip from the cone1 ScopeThis standard specifies the number 4,6,80,100,120,160,200 Metric cone and No. 0,1,2,3,4,5,6 Morse taper dimensions and tolerances. This standard applies to machine tools and tool shank with clips from the cone.2 Normative referencesThe following documents for the application of this document is essential. For cited documents with dates, only the dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document. GB/T 11334 Geometrical product specifications (GPS) taper tolerance3 taper tolerance11334 taper angle tolerances specified by the GB/T AT7, the outer conical positive bias, negative bias within the cone. Inner and outer conical basic dimensions and tolerances D, testing with the corresponding gauge.4 type and sizeCone type and size specified in Figure 1 to Figure 4 and Table 1. Note. The outer surface of the cone can be made discontinuous.1 with inner cone and outer cone end flat......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 1443-2016_English be delivered?Answer: Upon your order, we will start to translate GB/T 1443-2016_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 1443-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1443-2016_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 1443-2016?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1443-2016 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
