GB/T 13871.1-2022 PDF EnglishUS$320.00 · In stock · Download in 9 seconds
GB/T 13871.1-2022: Rotary shaft lip-type seals incorporating elastomeric sealing elements - Part 1: Dimensions and tolerances Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 13871.1: Historical versions
Similar standardsGB/T 13871.1-2022: Rotary shaft lip-type seals incorporating elastomeric sealing elements - Part 1: Dimensions and tolerances---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT13871.1-2022 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.140.50;23.100.60 CCS G 43 Replacing GB/T 13871.1-2007 Rotary shaft lip-type seals incorporating elastomeric sealing elements - Part 1: Dimensions and tolerances (ISO 6194-1:2007, Rotary shaft lip-type seals incorporating elastomeric sealing elements - Part 1: Nominal dimensions and tolerances, MOD) ISSUED ON: OCTOBER 12, 2022 IMPLEMENTED ON: MAY 01, 2023 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 Introduction ... 7 1 Scope ... 8 2 Normative references ... 8 3 Terms and definitions ... 8 4 Symbols ... 8 5 Construction type ... 9 6 Operating pressure, dimension series and tolerance ... 11 7 Requirements for shafts ... 14 8 Requirements for housings ... 15 9 Size identification code ... 17 10 Identification statement ... 17 Annex A (Informative) Structure number comparison list ... 18 Annex B (Informative) Seal specification ... 20 Bibliography ... 23 Rotary shaft lip-type seals incorporating elastomeric sealing elements - Part 1: Dimensions and tolerances1 ScopeThis document specifies the symbol, construction type, operating pressure, dimension series and tolerance, shaft requirements, cavity requirements and size identification codes of rotary shaft lip-type seals incorporating elastomeric sealing elements (hereinafter referred to as seals). This document applies to seals used under low pressure conditions (see 6.1).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For dated references, only the version corresponding to that date is applicable to this document; for undated references, the latest version (including all amendments) is applicable to this document. GB/T 1031-2009, Geometrical product specifications (GPS) - Surface texture: Profile method - Surface roughness parameters and their values GB/T 1800.2-2020, Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts (GB/T 1800.2-2020, ISO 286-2:2010, MOD) GB/T 13871.2, Rotary shaft lip-type seals incorporating elastomeric sealing elements - Part 2: Vocabulary (GB/T 13871.2-2015, ISO 6194-2:2009, MOD) GB/T 17446, Fluid power systems and components - Vocabulary (GB/T 17446-2012, ISO 5598:2008, IDT)3 Terms and definitionsFor the purposes of this document, the terms and definitions given in GB/T 13871.2 and GB/T 17446 apply.4 SymbolsThe following symbols apply to this document. h housing-bore depth b axial width (of the seal) l housing or shaft chamfer length d1 shaft diameter or main lip diameter of the seal D housing-bore diameter or seal outer diameter r corner radius of the housing bore5 Construction type5.1 Seal outside-diameter construction Figure 1 shows four basic types of outside-diameter construction of the seal. Figure 1 – Four basic types of outside-diameter construction 5.2 Seal construction without and with protection lip See Figure 2 for two types of seal construction without and with protection lip. See Figure 3 for the schematic diagram of the common construction of air-side surface of the sealing lip. Figure 3 – Construction of air-side surface of the sealing lip 5.4 Construction of the rubber-covered metal-cased seal See Figure 4 for the schematic diagram of the common construction of the rubber- covered metal-cased seal. 5.5 Construction code of the seal The various constructions shown in Figure 1, Figure 2, and Figure 3 can be combined and applied with each other, and the construction codes could be as follows: -- Single letters W, Z and B (see Figure 1) indicate the seal construction without protection lip and without wave-profile; -- Two-letters FB, FW and FZ, starting with F, indicate the seal construction with protection lip and without wave-profile; F indicates the existing of a protection lip, and the second letter indicates the outside-diameter construction (see Figure 1); -- Two-letters WL, ZL, BL, WR, ZR and BR, not beginning with F, indicate the seal construction without protection lip and with wave-profile; the first letter indicates the outside-diameter construction (see Figure 1), and the second letter indicates the direction of the wave-profile (see Figure 3); -- Three-letters FBL, FWL, FZL, FBR, FWR and FZR indicate the seal construction with protection lip and with wave-profile; the first letter F indicates the existing of the protection lip, the second letter indicates the outside-diameter construction (see Figure 1), and the third letter indicates the direction of the wave-profile (see Figure 3). The design of the sealing lip is mainly carried out by the manufacturer (to ensure sealing); it can also be agreed between the manufacturer and the buyer. Note: The constructions shown are only representative examples of the basic types. For the specific design details, refer to GB/T 9877-2008.6 Operating pressure, dimension series and tolerance6.1 Operating pressure Seals are normally used with atmospheric pressure on the air side, and sealing fluids at pressures of 0 kPa ~ 50 kPa above atmospheric pressure. The user shall consult the seal manufacturer regarding use at other pressures. 6.2 Dimension series The assembling diagram of the seal is shown in Figure 5 and the dimension series are given in Table 1. 7.2 Diametral tolerance The shaft shall have a diametral tolerance not greater than h11 as specified in GB/T 1800.2-2020. 7.3 Surface roughness and hardness 7.3.1 Surface roughness The seal contact surface of a ground shaft shall be finished to a surface roughness, measured in the axial direction of Ra 0.2 μm ~ Ra 0.8 μm, or Rz 0.8 μm ~ Rz 3.2 μm, as specified in GB/T 1031-2009. If the surface roughness value of the shaft does not fall within the limits given in this document, it shall be determined between the user and the seal manufacturer. 7.3.2 Surface hardness The surface hardness of the shaft shall be a minimum of HRC30. If the surface hardness of the shaft is less than HRC30, it shall be subject to agreement between the user and the seal manufacturer.8 Requirements for housings8.1 Dimensions 8.1.1 Where the housing is a rigid fully machined ferrous part, the housing bore shall conform to 8.2 and 8.3. 8.1.2 The housing bore shall be provided with a lead-in chamfer, free from burrs, as shown in Figure 7 and specified in Table 6. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 13871.1-2022 be delivered?Answer: The full copy PDF of English version of GB/T 13871.1-2022 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 13871.1-2022_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 13871.1-2022_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 13871.1-2022 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 13871.1-2022?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 13871.1-2022 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 13871.1-2022?A step-by-step guide to download PDF of GB/T 13871.1-2022_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 13871.1-2022". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
