GB/T 12347-2008 English PDFUS$189.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 12347-2008: Steel wire ropes -- Bending fatigue testing Status: Valid GB/T 12347: Historical versions
Basic dataStandard ID: GB/T 12347-2008 (GB/T12347-2008)Description (Translated English): Steel wire ropes -- Bending fatigue testing Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: H22 Classification of International Standard: 77.040.10 Word Count Estimation: 8,846 Date of Issue: 2008-08-19 Date of Implementation: 2009-04-01 Older Standard (superseded by this standard): GB/T 12347-1996 Regulation (derived from): National Standard Approval Announcement 2008 No.14 (Total No.127) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the rope bending fatigue tests of terms and definitions, test principle, testing machine, test procedures and test reports, specimens. This standard applies to a diameter of 60 mm wire rope in the following provisions of the plane under the conditions of repeated bending fatigue tests. GB/T 12347-2008: Steel wire ropes -- Bending fatigue testing---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Steel wire ropes.Bending fatigue testing ICS 77.040.10 H22 National Standards of People's Republic of China Replacing GB/T 12347-1996 Steel wire rope bending fatigue test method Posted.2008-08-19 2009-04-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China China National Standardization Administration released ForewordThis standard reference ГОСТ2387-1980 "wire rope fatigue test method" to be revised, this standard consistent with ГОСТ2387-1980 Sexuality is not equivalent. This standard replaces GB/T 12347-1996 "wire rope bending fatigue test method." This standard compared with GB/T 12347-1996 main changes are as follows. --- Increased package angle, bending fatigue frequency, bending fatigue cycle, bending fatigue terms such as terminology; --- The term "bending pulley" is modified to "test wheel"; --- Remove the fatigue testing machine A, B, C, D, E-type classification; --- Give the principle of selection of test parameters; --- Delete Appendix A This standard is proposed by China Iron and Steel Association. This standard by the National Steel Standardization Technical Committee. This standard was drafted. National Metal Products Quality Supervision and Inspection Center, Guizhou Steel Co., Ltd., Shanghai Steel Group Baosteel have Limited company. The main drafters of this standard. Liu Guisen, Heng Junhua, He Guangcheng, Zhang Jian, Zhou Yi. This standard replaces the standards previously issued as follows. --- GB/T 12347-1990, GB/T 12347-1996. Steel wire rope bending fatigue test method1 ScopeThis standard specifies the terms and definitions of wire rope bending fatigue test, test principle, test machine, sample, test procedures and test reports. This standard applies to the following wire rope diameter 60mm under repeated bending plane fatigue test.2 Terms and definitionsThe following terms and definitions apply to this standard. 2.1 Specimen in the same plane through the test wheel to a certain direction of bending a certain degree of fatigue test. The principle shown in Figure 1. Figure 1 plane unidirectional bending fatigue schematic diagram 2.2 The sample in the same plane through the test wheel to a certain direction after bending a certain angle in the opposite direction and then bent a certain angle (ie, S-bend) stress test. The principle shown in Figure 2. 2.3 Installed in the bending fatigue testing machine, and can turn around a certain curvature, in order to drive the sample in the effective length of the repeated bending movement of the slip Wheel or reel. 2.4 Installed in the bending fatigue testing machine, and can make the sample repeatedly bending a certain angle of the pulley, which is a key component of fatigue testing machine, which Wheel groove shape as shown in Figure 3. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 12347-2008_English be delivered?Answer: Upon your order, we will start to translate GB/T 12347-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 12347-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 12347-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 12347-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 12347-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
