GB/T 11413-2015 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 11413-2015: Test method for bond strength of leather shoes heels Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 11413: Historical versions
Similar standardsGB/T 11413-2015: Test method for bond strength of leather shoes heels---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT11413-2015GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 61.060 Y 78 Replacing GB/T 11413-2005 Test method for bond strength of leather shoes heels Issued on: SEPTEMBER 11, 2015 Implemented on: APRIL 1, 2016 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration Committee. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Principle... 4 4 Test equipment ... 4 5 Sample and environmental regulation ... 7 6 Test conditions ... 8 7 Test steps ... 8 8 Test results ... 9 9 Test report ... 9ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard replaces GB/T 11413-2005 Test methods for bond strength of leather shoes heels. Compared with GB/T 11413-2005, the main modifications are as follows. - added GB/T 16825.1-2008 Verification of static uniaxial testing machines - Part 1. Tension/compression testing machines - Verification and calibration of the force-measuring system in normative references; - added two forms of pull fixtures for different heel forms; - described some actual situations in the test results. Attention is drawn to the possibility that some of the elements of this Standard may be the subject of patent rights. The issuing authority shall not be held responsible for identifying any or all such patent rights. This Standard was proposed by China Light Industry Federation. This Standard shall be under the jurisdiction of Sub-committee on Leather Shoes, National Technical Committee on Footwear of Standardization Administration of China (SAC/TC305/SC1). The drafting organizations of this Standard. Wenzhou Quality and Technical Supervision and Inspection Institute [National Footwear Quality Supervision and Inspection Center (Wenzhou)], China Leather and Footwear Industry Research Institute, Zhejiang Red Dragonfly Footwear Company Limited, Wenzhou Haibin Xiu Long Shoes Co., Ltd. Main drafters of this Standard. Ye Zhengmao, Yang Zhimin, Yu Shuxian, Shang Yuanjun, Zhang Xiulong, Mao Xiaohui, Pan Wenwen. Versions of standard substituted by this Standard are. - GB/T 11413-1989, GB/T 11413-2005. Test method for bond strength of leather shoes heels1 ScopeThis Standard specifies the test method for the bond force of the heel and the posterior or outer soles. This Standard is applicable to heel and heel lasting or shoes adhesive or stapled with outsole. This Standard is not applicable to leather shoes of which the heel is integrated with the outsole.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 16825.1-2008, Verification of static uniaxial testing machines - Part 1. Tension/compression testing machines - Verification and calibration of the force-measuring system3 PrinciplePut the finished shoes on a special fixture. Stretch to the heel and posterior or outsole for separation on the tensile testing machine at a certain speed. The required force shall be bond strength of leather shoes heels.4 Test equipment4.1 Tensile testing machine 4.1.1 Tensile testing machine shall meet the requirements of GB/T 16825.1-2008. The maximum load shall not be less than 1500 N. 4.1.2 The precision is grade 2. 4.1.3 The stretching speed can be adjusted to (25 ± 2) mm/min. lasting or outsole. Stop immediately and record the maximum load. 7.7 During the test, if the upper is torn or the heel is separated and the insole is pulled out, if the heel is not separated from the heel lasting or outsole, it shall terminate the test and record the maximum load. 7.8 During the test, if it reaches to the maximum load of the testing machine due to excessive bond strength of heel but the heel is still not separated from the heel lasting or outsole, it shall terminate the test and record the maximum load. 7.9 During the test, if the heel is broken or fractured, the heel is not separated from the heel lasting or outsole, it shall terminate the test and record the maximum load. 7.10 If it only measures whether the heel bond strength meets the specified value requirements, then when the load value reaches the product standard value, it shall check whether the heel is separated from the heel lasting or outsole after the load is maintained for 15s ~ 20s. 7.11 The other samples shall be carried out in the same method.8 Test results8.1 Take the maximum load recorded during the test as the test results, in Newtons (N). The test results shall be neatest to 5N. 8.2 During the test, if the heel is not separated from the heel lasting or outsole after there is situation described in 7.7, 7.8, 7.9 or 7.10 test, it shall take the maximum load recorded as the test results and indicate “unseparated” as well as the corresponding situation. 8.3 The test results for each shoe shall be expressed separately.9 Test reportThe test report shall contain the following information. a) reference to this test method; b) descriptions on test specimen name, heel height, fixture type, heel material, heel assembly form (adhesive or stapling), heel separation; c) heel bond strength; d) tester and test date. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 11413-2015 be delivered?Answer: The full copy PDF of English version of GB/T 11413-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 11413-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 11413-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 11413-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 11413-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 11413-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 11413-2015?A step-by-step guide to download PDF of GB/T 11413-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 11413-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
