GB/T 10580-2015 English PDFUS$214.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 10580-2015: Standard conditions for use prior to and during the testing of solid electrical insulating materials Status: Valid GB/T 10580: Historical versions
Basic dataStandard ID: GB/T 10580-2015 (GB/T10580-2015)Description (Translated English): Standard conditions for use prior to and during the testing of solid electrical insulating materials Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: K15 Classification of International Standard: 29.035.01 Word Count Estimation: 11,148 Date of Issue: 2015-07-03 Date of Implementation: 2016-02-01 Older Standard (superseded by this standard): GB/T 10580-2003 Quoted Standard: GB/T 1034-2008; GB/T 2421.1-2008; IEC 60216-4-1 Adopted Standard: IEC 60212-2010, IDT Regulation (derived from): National Standard Announcement 2015 No.22 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Standard specifies the acceptable conditions of solid insulating materials test specimen exposure time, temperature, humidity and atmospheric immersion, the range is wide enough to ensure that we have chosen for the right conditions, so as to achieve a) or b), any purpose. To get better reproducibility of test results: a) elimination portion of the test sample before experienced environmental conditions on the performance of a sample (often called "normalization process" of this standard called preconditioning); b) to ensure consistent conditions during the test. This Standard does not apply to determine the influence of certain temperatures and humidity or immersion of the material, GB /T 2421.1-2008 gives the procedures and environmental impact of the materials. GB/T 10580-2015: Standard conditions for use prior to and during the testing of solid electrical insulating materials---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Standard conditions for use prior to and during the testing of solid electrical insulating materials ICS 29.035.01 K15 National Standards of People's Republic of China Replacing GB/T 10580-2003 Solid insulating material before the test and Standard test conditions employed (IEC 60212.2010, IDT) Issued on. 2015-07-03 2016-02-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsPreface Ⅰ Introduction Ⅱ 1 Scope 1 2 Normative references 1 3 Terms and definitions 4 recommended pretreatment conditions and handling conditions of the test (or immersion fluid) temperature and humidity 2 5 conditional processing cycle 3 6 in air pretreatment, processing conditions and test procedures 3 7 immersed in liquid processing conditions and test 4 8 4 standard reference atmosphere 9 pretreatment, processing conditions and test conditions for symbolic representation 4 10 4 ReportForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. This standard replaces GB/T 10580-2003 "standard conditions and solid insulating materials used in the test before the test" and GB/T 10580 -2003 Compared to the main technical changes are as follows. --- The "Overview" As an introduction listed separately (see Introduction, Chapter 1 of the 2003 edition); --- On the "scope" is further described (see Chapter 1, Chapter 2 of the 2003 edition); --- Added "Normative references" (see Chapter 2); --- Increasing the "insulation material", "sample", "container", "workspace", "conditional processing cycle", "restore", "vapor pressure", "saturated steam Pressure "," aging "of nine terms and definitions (see Chapter 3); --- Added "Report" (see Chapter 10); --- Amend Table 2 of "temperature", "relative humidity" part deviation range (see Table 2). This standard uses the translation method identical with IEC 60212.2010 "standard conditions and solid insulating materials used in the test before the test." Correspondence between the consistency of the standards of international documents and normative references of the following documents. --- GB/T 11026.4-2012 heat resistance, electrical insulating materials - Part 4. Ageing ovens - Single Room (IEC 60216-4-1.2006, IDT). The standard proposed by China Electrical Equipment Industrial Association. This standard by the National Electrical insulation materials and insulation systems assessment Standardization Technical Committee (SAC/TC301) centralized. This standard was drafted. Guilin Electric Apparatus Research Institute Co., Ltd., Shunde District of Foshan City of Quality and Technology Supervision of standards and codes, mechanical Industrial Electrical Technology Beijing Institute of Economic Research. The main drafters of this standard. Song Yuxia, Luozhuan Yong, Liu Yali SCENCE Liu Hui. This standard replaces the previous version published case. --- GB/T 10580-1989, GB/T 10580-2003.IntroductionSome performance of most insulating materials which by its temperature atmospheric environment, humidity or temperature and humidity combined action, Therefore, when the solid insulating material tested in the test sample should be controlled before subjected to environmental conditions (such as temperature and humidity) and the actual Environmental conditions of the test. According to the material specification and intended use to select the appropriate test conditions and treatment conditions, unless otherwise specified, The environmental conditions should be the same when the condition of the sample processing and testing. For the above-mentioned factors may be affected by an insulating material, it should be given their test results at the same time a description of the sample exposed strip Parts, so such materials should be standardized before the test sample was exposed to the atmospheric conditions and the specimen which when tested provisions. Solid insulating material before the test and Standard test conditions employed1 ScopeThis standard specifies the acceptable conditions of solid insulating materials test specimen exposure time, temperature, humidity and atmospheric immersion, scope foot Wide enough to ensure that we have chosen for the right conditions, so as to achieve a) or b) any purpose. To get better reproducibility of test results. a) part of the impact of the elimination of the test sample before the environmental conditions experienced by the sample properties (usually called "normalization process" of this standard Called pre-treatment); b) to ensure consistent conditions during the test. This standard does not apply to determine the influence of certain temperatures and humidity or immersion of the material, GB/T 2421.1-2008 gives the environment and Movies Sound procedures related material.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 1034-2008 Plastics Determination of water absorption (ISO 62.2008, IDT) GB/T 2421.1-2008 Environmental testing for electric and electronic products overview and guidance (IEC 60068-1. 1988, IDT) IEC 60216-4-1 Electrical insulating materials - Thermal resistance - Part 4-1. Ageing ovens - Single - chamber ovens (Electricalinsulating materials-Thermalenduranceproperties-Part 4-1. Ageingovens-Single-chamberovens)3 Terms and DefinitionsThe following terms and definitions apply to this document. 3.1 Insulation material insulatingmaterial Having negligible low conductivity of the solid material used to isolate the potential of different conductor portions. Note 1. In English, "insulating material" is sometimes also referred to a wide range of meaning insulating liquids and gases. Note 2. The insulation material may be a solid, liquid or gas, or a combination thereof, the present standard only relates to a solid insulating material. 3.2 Specimen specimen Standard samples used in the test insulating materials related test specification describes. 3.3 Preconditioning preconditioning In order to eliminate or partly eliminate the test specimen before experiencing environmental conditions (mainly temperature and humidity) on the performance of the sample handling method. Note 1. This process is sometimes referred to as "normalization process." Note 2. The pre-treatment is usually conditional processing before the sample is carried out. When the temperature and humidity conditions for handling and pretreatment temperature and humidity are the same, you can The pre-treatment and conditions of the merger process, can also be replaced by preprocessing conditional processing. Note 3. Other conditions may be affected by the pretreatment environment, electricity or the relevant test specifications required in the sample which effects adjustment. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 10580-2015_English be delivered?Answer: Upon your order, we will start to translate GB/T 10580-2015_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 10580-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 10580-2015_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 10580-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 10580-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
