GB/T 10266-2008 PDF EnglishUS$190.00 · In stock · Download in 9 seconds
GB/T 10266-2008: Specification for sintered uranium dioxide pellets Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 10266: Historical versions
Similar standardsGB/T 10266-2008: Specification for sintered uranium dioxide pellets---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT10266-2008GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 27.120.30 F 46 Replacing GB/T 10266-1998 Specification for sintered uranium dioxide pellets ISSUED ON: JUNE 19, 2008 IMPLEMENTED ON: APRIL 01, 2009 Issued by: General Administration of Quality Supervision, Inspection and Quarantine of PRC; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Technical requirements ... 5 4 Requirements of pellets batch ... 9 5 Sampling ... 10 6 Test and inspection ... 10 7 Quality certification documents ... 11 8 Packaging and transportation ... 11 Appendix A (Informative) Comparison of clause number between this standard and ASTM C 776:2006 ... 13 Appendix B (Informative) The technical differences between this standard and ASTM C 776:2006 and their reasons ... 14 Appendix C (Informative) Load capacity test of pellets ... 15 Specification for sintered uranium dioxide pellets1 ScopeThis standard specifies the technical requirements, pellet batches, sampling, testing and inspection, packaging and transportation requirements for sintered uranium dioxide pellets (hereinafter referred to as "pellets"). This standard is applicable to pellets with various 235U enrichments for nuclear reactors. This standard does not include the relevant content of the prevention of criticality accidents and the requirements for safety and health. The use of this standard shall also comply with relevant national regulations on nuclear material control, transportation, handling, use.2 Normative referencesThe provisions in following documents become the provisions of this Standard through reference in this Standard. For the dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Standard; however, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies. GB/T 10265 Specification for nuclear grade sinterable uranium dioxide powder (GB/T 10265-2008, ASTM C753:2004, MOD) GB 11806 Regulations for the safe transport of radioactive material (GB 11806-2004, IAEA Safety Standards Serries No. TS-R-1, 2003, IDT) GB/T 13696 Specification for uranium hexafluoride enriched to less than 5% 235U EJ/T 689 Testing method for the thermal-stability of sintered UO2 pellets3 Technical requirements3.1 Chemical requirements All chemical analysis samples shall be representative AND meet the requirements of Chapter 5. All chemical analysis methods shall adopt national standards or industry standards, OR the methods agreed upon by both parties. the buyer, such as the load-bearing capacity test. Refer to Appendix C for the load-bearing capacity test method. 3.3.4.1 Surface cracks a) Axial crack length (including cracks extending to the end of the pellet): Less than one-half of the height; b) Circumferential crack length: Less than one-third of the circumference. 3.3.4.2 Block loss a) Cylindrical surface block loss 1) Cylindrical surface block loss: Less than 5% of the surface area of the cylindrical surface of the pellet; 2) Maximum linear size: The maximum linear size shall be able to ensure that, the fuel performance remains stable during use; its limit shall be negotiated by the supplier and the demander. b) Block loss at the end of pellet: less than 1/3 of the area of the end of the pellet (can be detected by 1/3 of the circumference of the pellet end defect). 3.3.5 Appearance quality of pellets The surface of the finished pellets shall be free of visible slag and foreign matter, such as oil stains and grinding media. 3.4 Marking A mark or code shall be used to identify the 235U enrichment of the pellets. 3.5 Irradiation stability In order to evaluate the radiation stability of pellets, EJ/T 689 shall be used for thermal stability test.4 Requirements of pellets batch4.1 Pellets, which are made from the same batch of uranium dioxide powder, meet the requirements of GB/T 10265, use the same group of process parameters, are defined as a pellet batch. 4.2 The identification of a pellet batch shall be retained, throughout the production process. In the whole process, it shall ensure the identity of batch materials; it is not allowed for mixing of materials.5 Sampling5.1 Sampling, weighing, sample processing must be carried out, under conditions that ensure that the sample is representative of the batch. The sampling plan, which meets the acceptance criteria, shall be negotiated by both the supplier and the buyer. 5.2 The purchaser has the right to select a representative sample from each pellet batch, AND determine its chemical, nuclear or physical properties. 5.3 The batch of samples shall have a sufficient number of pellets, so that it can carry out the quality inspection and arbitration test if necessary, at the supplier's factory, as well as the acceptance test, at the buyer's factory, when necessary. 5.4 When necessary, the batch of samples for acceptance test at the buyer's factory shall be put into a separate container; the batch number shall be clearly marked; it can be shipped before or with the batch of pellets. The arbitration samples shall be clearly marked AND kept in the supplier’s factory, until the buyer formally accepts the batch of pellets.6 Test and inspection6.1 The supplier shall test samples, in accordance with the requirements described in Chapter 5, to ensure that the pellets meet the requirements of Chapter 3. All tests shall be carried out on the basis of technology, which is agreed upon by the supplier and the buyer. 6.2 Within the time period, which is agreed upon between the supplier and the buyer, the supplier shall save all results AND provide all results when required, to prove that the pellets meet the requirements described in Chapter 3. 6.3 The buyer can use the samples, which are provided by the supplier, OR samples, which are taken from the buyer's factory, for acceptance tests. Acceptance shall be based on a batch of pellets; it shall depend on the material properties, which meet the requirements of Chapter 3 OR the requirements after amended according to the contract documents. 6.4 If there is a dispute over the analysis results, a third party, which is agreed upon by the supplier and the buyer, shall be determined as the arbitrator. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 10266-2008 be delivered?Answer: The full copy PDF of English version of GB/T 10266-2008 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 10266-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 10266-2008_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 10266-2008 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 10266-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 10266-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 10266-2008?A step-by-step guide to download PDF of GB/T 10266-2008_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 10266-2008". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
