GB 3263-2008 English PDFUS$279.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB 3263-2008: Food additive -- Propyl gallate Status: Obsolete GB 3263: Historical versions
Basic dataStandard ID: GB 3263-2008 (GB3263-2008)Description (Translated English): Food additive -- Propyl gallate Sector / Industry: National Standard Classification of Chinese Standard: X41 Classification of International Standard: 67.220.20 Word Count Estimation: 7,770 Date of Issue: 2008-12-03 Date of Implementation: 2009-06-01 Older Standard (superseded by this standard): GB 3263-1982 Quoted Standard: GB/T 601; GB/T 602; GB/T 603; GB/T 617; GB/T 5009.3; GB/T 5009.4; GB/T 5009.75; GB/T 5009.76; GB/T 6682 Regulation (derived from): Announcement of Newly Approved National Standards No. 19 of 2008 (No. 132 overall) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Chinese standard specifies the food additive propyl gallate technical requirements, test methods, inspection rules, marking, packaging, transportation, storage and shelf life. This standard applies to gallic acid and n-propanol in acidic dehydrating agent under conditions of heating esterification of gallic acid propyl. GB 3263-2008: Food additive -- Propyl gallate---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Food additive.Propyl gallate ICS 67.220.20 X41 National Standards of People's Republic of China Replacing GB 3263-1982 Food Additives gallic acid ester Published 2008-12-03 2009-06-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China issued ForewordChapter 4 of this standard is mandatory, the rest are recommended. This standard is used by the US to modify "Food Chemical Codex" (FOODCHEMICALSCODEX) (fifth edition) specifications. The main difference between this standard and the US "Food Chemical Codex" (fifth edition) technical specifications are. increasing the limit of arsenic. Instead of the standard GB 3263-1982 "Food Additives gallic acid ester." This major change compared to the standard GB 3263-1982 as follows. --- cancel the original standard limits of heavy metals; --- physical and chemical indicators increased the limit of lead. This standard is proposed and managed by the National Standardization Technical Committee on Food Additives. Drafted by. China Food Fermentation Industry Research Institute, Zhangjiajie trade sources Chemical Co., Ltd. The main drafters. Lihui Yi, Tang Xian-red, wood Qiuer, Chen Xueyong, soup Hz. This standard supersedes the previous editions are. --- GB 3263-1982. Food Additives gallic acid ester Range 1 This standard specifies the food additive gallic acid propyl technical requirements, test methods, inspection rules, marking, packaging, transportation, storage and Shelf life. This standard applies to gallic acid and n-propanol at an acidic dehydrating agent, heating the obtained esterifying gallic acid ester.2 Normative referencesTerms of the following documents become provisions of this standard by reference in this standard. For dated reference documents, all later Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to agreements based on this standard Whether the latest versions of these documents. For undated references, the latest version applies to this standard. Preparation GB/T 601 standard titration solution Chemicals GB/T 602 Chemicals determination of impurities in the prepared standard solution (GB/T 602-2002, ISO 6353-1. 1982, NEQ) with GB/T 603 Test Methods Chemicals Preparations of articles (GB/T 603-2002, ISO 6353-1 with. 1982, NEQ) GB/T 617 melting point range of the assay Chemicals General procedure (GB/T 617-2006, ISO 6353-1. 1982, NEQ) Determination GB/T 5009.3 moisture in food Determination GB/T 5009.4 ash in foods Determination of lead in food additives 5009.75 GB/T Determination of arsenic in food additives 5009.76 GB/T GB/T 6682 for analytical laboratory use specifications and test methods (GB/T 6682-2008, ISO 3696. 1987, MOD) Formula 3, formula and molecular weight Formula 3.1 C10H12O5. 3.2 division Structure HO HO COO (CH2) 2CH 3 HO 3.3 Molecular Weight 212.20 (according to 2001 international atomic mass table). 4. Technical Requirements 4.1 Sensory requirements White or milky white crystalline powder. 4.2 Physical and Chemical Indicators Shall comply with the requirements in Table 1. Table 1 Physical and Chemical Indicators Item Index Content (in terms C10H12O5)/98.0 to 102.0% Melting point/℃ 146 ~ 150 Arsenic (As)/(mg/kg) ≤ 3 Lead (Pb)/(mg/kg) ≤ 1 Loss on drying /% ≤ 0.5 Residue on ignition /% ≤ 0.15 Test methodsUnless otherwise stated, use only confirmed in the analysis of analytical grade reagents and GB/T 6682 stipulated water. Standard used in the analysis Titration solution, standard solution, the determination of impurities, products and preparations, in the absence of other requirements specified, are by GB/T 601, GB/T 602, GB/T 603 Preparation predetermined. When present in the standard solution which is formulated with a solvent not specified, refer to an aqueous solution. 5.1 sensory testing Proper amount of sample is placed in a clean, dry porcelain dish, under natural light, its appearance was observed. 5.2 Identification of 5.2.1 Reagents and solutions a) ferric chloride solution. mass fraction of 1%; b) ethanol solution. volume fraction of 75%; c) Sodium hydroxide solution. 1mol/L. 5.2.2 Operation 5.2.2.1 About 0.5g sample was dissolved in 10mL1mol/L sodium hydroxide solution, distilled, the distillate take approximately 4 mL, which was to be clarified, There propanol odor when heated. 5.2.2.2 Approximately 0.1g sample was dissolved in 5mL75% ethanol solution, add 1 drop of 1% ferric chloride solution, it was purple. 5.3 Content 5.3.1 Reagents and solutions a) bismuth nitrate solution. Weigh 5g of bismuth nitrate [Bi (NO3) 3 · 5H2O], placed in an Erlenmeyer flask, were added 7.5mL of nitric acid and 10mL Water, shaken vigorously and dissolved, cooled, filtered, diluted with water to 250 mL volume, backup. b) nitric acid solution. nitric acid. water = 1.300 (volume ratio). 5.3.2 Analysis of step Sample pre-weighed 200mg 4h dried to constant weight of 110 ℃ (accurate to 0.0001g), was placed in a 400mL beaker, add 150mL dissolved in water, heated to boiling, shaking vigorously, add 50mL bismuth nitrate test solution, heating was continued for several minutes to boiling until complete precipitation, cooling, Filtered and the yellow precipitate was filtered off Yu Heng weight of the acid-fritted funnel, washed with a nitric acid solution, and dried at 110 ℃ 4h, referred to constant weight. 5.3.3 calculation results Content (mass fraction) of gallic acid propyl ester (C10H12O5) according to formula (1). 100 (1) Where. The X1 --- propylene content of gallic acid (C10H12O5) (mass fraction),%; 0.4866 --- gallic acid propyl bismuth salt in terms of coefficient of gallic acid propyl; 5.3.4 allows poor The results measured results of two parallel arithmetic mean subject (to one decimal place). Twice obtained under repeatability conditions alone Li absolute difference measurement must not exceed 0.2% of the arithmetic mean. 5.4 Melting point Measurement sample previously dried at 110 ℃ 4h to constant weight, then GB/T 617 a predetermined method. 5.5 Arsenic Testing according to GB/T 5009.76 predetermined. 5.6 Lead Testing according to GB/T 5009.75 predetermined. 5.7 Loss on drying Measuring (110 ℃, dried 4h) The method according to GB/T 5009.3 predetermined. 5.8 Residue on ignition Weigh about 2g sample (accurate to 0.0001g), measured as GB/T 5009.4 predetermined.6 Inspection Rules6.1 determine batches To determine the lot number of the product in accordance with its respective rules by the quality inspection departments of production units, the final mixing and there is uniformity of quality of production Product batch. 6.2 Sampling and sample volume Randomly selected samples from each batch, each batch of 3% of the number of extracted sample packages, each consisting of not less than three packages, each package Samples taken not less than 100g, the extracted sample is rapidly mixed, dispensed into two clean, dry container or bag, marked green Production plant, product name, batch number, quantity and date of sampling, as a test, a seal retained for future reference. 6.3 factory inspection 6.3.1 factory inspection items include content, loss on drying and burning debris. 6.3.2 Each batch of products subject to the inspection department of the production plant according to the method specified in this standard test, issued before the factory and product certification. 6.4 Type inspection All items specified in Chapter 4 are type test items. Type test once every year, or when one of the following occurs When tested. --- large change material, the process occurs; --- discontinued after resume production; --- when there is a large difference between the factory inspection results with normal production; --- Quality Supervision, Inspection agency when requested. 6.5 determine the rules When tested on all the technical requirements, test results if an index does not meet the requirements of this standard should be re-sampled for a double double Inspection. Review the results even if one does not meet this standard, the entire batch of products as unqualified. When the supply and demand sides as opposition occurred on product quality, selected by mutual agreement arbitration body, carried out as specified in this standard test method arbitration. 7 signs, packaging, transportation, storage and shelf life 7.1 marks Food additives must be packaged logo and product brochures, signs content may include. name, place of origin, name, health permits, production License number, specifications, production date, lot number or code, shelf life, etc., and clearly indicate the words "food additive" on the sign. Book GB 3263-2008 7.2 Packaging Packaged products should be approved by the state, and in accordance with appropriate food packaging materials with health standards. 7.3 Transport Carry goods should not be mixed with toxic and hazardous substances and contamination during transport to avoid the rain and sun and so on. 7.4 Storage Airiness product, clean, dry place, can not coexist with toxic, hazardous and corrosive substances and the like. 7.5 Shelf Life Products from the production date, in conformity with the above conditions, storage and transportation, packaging intact, the shelf life of not less than 12 months. 8002- ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB 3263-2008_English be delivered?Answer: Upon your order, we will start to translate GB 3263-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB 3263-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB 3263-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB 3263-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB 3263-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
