GB 28736-2019 PDF EnglishUS$130.00 · In stock · Download in 9 seconds
GB 28736-2019: Minimum allowable values of energy efficiency and energy efficiency grades for welding machine Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB 28736: Historical versions
GB 28736-2019: Minimum allowable values of energy efficiency and energy efficiency grades for welding machine---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB28736-2019 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 27.010 F 01 Replacing GB 28736-2012 Minimum allowable values of energy efficiency and energy efficiency grades for welding machine Issued on. DECEMBER 31, 2019 Implemented on. JULY 01, 2020 Issued by. State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 4 2 Normative references... 4 3 Terms and definitions... 5 4 Energy efficiency grades of welding machine... 5 5 Technical requirements... 6 6 Test methods... 9ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard replaces GB 28736-2012 “Minimum allowable values of energy efficiency and energy efficiency grades for arc welding machines”. Compared with GB 28736-2012, in addition to editorial modifications, the main technical changes are as follows. -- added the term and definition of minimum allowable values of energy efficiency for welding machines (see 3.1); -- added the energy efficiency grades of resistance welding machine (see Table 7 ~ Table 10 of Clause 5); -- added the test methods (see Clause 6). This Standard was proposed by and shall be under the jurisdiction of Standardization Administration of the People's Republic of China. The drafting organizations of this Standard. China National Institute of Standardization, Chengdu Sanfang Electric Co., Ltd., Tangshan Kaiyuan Electric Group Co., Ltd., Shenzhen Jiashi Technology Co., Ltd., Shanghai Hugong Welding Group Co., Ltd., Shenzhen Ruiling Industrial Co., Ltd., Hangzhou Kaierda Welding Machine Co., Ltd., Shenzhen Hongbai Technology Industrial Co., Ltd., Shanghai General Electric Welding Machine Co., Ltd., Tianjin Seven Institute of Technology, Shenzhen Megmit Electric Co., Ltd., Zhejiang Kende Mechanical & Electrical Co., Ltd., Ohara (Nanjing) Electromechanical Co., Ltd., Shanghai Weiteli Welding Equipment Manufacturing Co., Ltd., Chengdu Welding Technology Co., Ltd., Dongguan Pengyu Weigao Intelligent Technology Co., Ltd., Ningxia Wuzhong Haoyun Electric Welder Co., Ltd., Jiangsu Zhenan Equipment Technology Co., Ltd., Yongkang Jiaxiao Welding Automation Equipment Co., Ltd., Jinzhou Shenghe Technology Electronics Co., Ltd., Hunan Chuen Information Technology Co., Ltd. Main drafters of this Standard. Liu Ren, Yang Qingxun, Su Dong, Chen Jie, Luo Weihong, Shu Zhenyu, Wang Wei, Hou Runshi, Han Peiwen, Wang Jincheng, Zhu Xuanhui, Zhao Zhongqiu, He Zhijun, Zhang Zuwang, Liu Qun, Yang Guang, Liu Xingwei, Zhou Yin, Li Feng, Cheng Haojian, Xia Jifu, Chen Jia. Version of standard substituted by this Standard is. - GB 28736-2012. Minimum allowable values of energy efficiency and energy efficiency grades for welding machine1 ScopeThis Standard specifies the energy efficiency grades, minimum allowable values of energy efficiency and test methods for arc welding machine and resistance welding machine. This Standard is applicable to the arc welding machine and resistance welding machine that are designed for industrial and professional use, not exceeding the voltage specified in GB/T 156. The resistance welding machine to which this Standard applies specifically refers to the resistance welding transformer which is finally installed with the frame, the input circuit and the secondary circuit. This Standard is not applicable to AC TIG arc welding machine, AC and DC TIG arc welding machine, power frequency secondary rectification resistance welding machine, seam welding machine, resistance butt welding machine, flash butt welding machine, energy storage resistance welding machine, inverter AC resistance welding machine, separately-sold resistance welding transformer and mechanical equipment driven welding machine.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 156, Standard Voltages GB/T 2900.22, Electrotechnical terminology - Electric welding machine GB/T 8118, The general specification for arc welding machines GB/T 8366, Resistance welding - Resistance welding equipment - Mechanical and electrical requirements GB/T 14549-1993, Quality of Electric Energy Supply - Harmonics in Public Supply Network GB 15578, Safety requirements for resistance welding machine3 Terms and definitionsFor the purposes of this document, the terms and definitions defined in GB/T 2900.22, GB/T 8118, GB/T 15579.1, GB/T 8366, GB 15578, and GB/T 25301 as well as the followings apply. 3.1 minimum allowable values of energy efficiency for welding machines The maximum guaranteed value of allowable efficiency of an arc welding machine in the rated state, the maximum limit of short circuit loss allowed by a resistance welding machine in the rated gear, under standard-specified test conditions. 3.3 short circuit loss for resistance welding machine The active power input to a resistance welding machine when the secondary winding of the resistance welding machine (where applicable, including a rectifier) is in the best short circuit condition, and at the rated gear position, an appropriate voltage at the rated frequency is applied to the primary winding of the resistance welding machine, when the current flowing through the primary winding is the continuous input current I1P of the resistance welding machine.4 Energy efficiency grades of welding machineThe energy efficiency grade of welding machine is divided into 3 grades, where grade 1 is the highest energy efficiency. The energy efficiency indicators of arc welding machines at all grades shall comply with corresponding provisions in Table 1 ~ Table 6.5 Technical requirementsThe minimum allowable values of energy efficiency for welding machines shall be grade 3 energy efficiency, where the efficiency (%) of the arc welding machine shall not be lower than the grade 3 requirements in Tables 1 ~ Table 6 and the short circuit loss for resistance welding machine shall not be higher than the grade 3 requirements in Table 7 ~ Table 10.If the nominal load duration of resistance welding machine is 50%, the power S50, not consistent with the S50 determined in Tables 7 ~ Table 10, it shall comply with the provisions on grade 3 corresponding to the adjacent small nominal power S50.6 Test methods6.1 Test conditions A new, dry, and fully-installed welding machine shall be tested at an ambient Nominal power S50 of 6.3 Power supply 6.3.1 Classification and parameters of power supply mode When measuring the energy efficiency indicators of arc welding machines and resistance welding machines, if grid power is used, the power of the input power inlet of the welding machine shall meet the requirements of 6.3.2. 6.3.2 Grid power supply The power supply shall meet the requirements of GB/T 156 and meet the following requirements. 6.3.3 Variable frequency power supply When measuring the energy efficiency of an inverter resistance welding machine, it requires variable frequency power supply or power supply by variable frequency controller of resistance welding machine. In addition to self- power supply by inverter controller that supports the resistance welding machine, the inverter power supply to the inverter resistance welding machine 6.4 Test site layout 6.4.1 Welding machine layout When conducting the energy efficiency test on welding machines, the test site layout of welding machines shall meet the following requirements. 6.4.2 Input cable layout When conducting the energy efficiency test on welding machines, the input cable layout shall meet the following requirements. 6.4.3 Measuring device layout When conducting the energy efficiency test on welding machines, the measuring device layout shall meet the following requirements. 6.5 Energy efficiency measurement of welding machines with two or more welding functions If a welding machine has two or more welding functions, its energy efficiency test shall meet the following requirements. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 28736-2019 be delivered?Answer: The full copy PDF of English version of GB 28736-2019 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 28736-2019_English with my colleagues?Answer: Yes. The purchased PDF of GB 28736-2019_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 28736-2019 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB 28736-2019?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB 28736-2019 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB 28736-2019?A step-by-step guide to download PDF of GB 28736-2019_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 28736-2019". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
