GB 1886.340-2021 PDF EnglishUS$95.00 · In stock · Download in 9 seconds
GB 1886.340-2021: National food safety standard - Food additives - Potassium pyrophosphate Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB 1886.340-2021: National food safety standard - Food additives - Potassium pyrophosphate---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB1886.340-2021GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA National food safety standard - Food additives - Potassium pyrophosphate ISSUED ON: FEBRUARY 22, 2021 IMPLEMENTED ON: AUGUST 22, 2021 Issued by: National Health Commission of the People's Republic of China; State Administration for Market Regulation. Table of ContentsForeword ... 3 1 Scope ... 4 2 Molecular formula and relative molecular mass ... 4 3 Technical requirements ... 4 Appendix A Inspection method ... 6 National food safety standard - Food additives - Potassium pyrophosphate1 ScopeThis Standard applies to the food additive potassium pyrophosphate that is produced with potassium hydroxide and the food additive phosphoric acid (including wet-process phosphoric acid) as raw materials.2 Molecular formula and relative molecular mass2.1 Molecular formula K4P2O7 2.2 Relative molecular mass 330.34 (according to the 2018 international relative atomic mass)3 Technical requirements3.1 Sensory requirements Sensory requirements shall be in accordance with Table 1. Table 1 – Sensory requirements 3.2 Physical and chemical indicators Physical and chemical indicators shall be in accordance with Table 2. Table 2 – Physical and chemical indicatorsAppendix AInspection method WARNING: Some reagents which are used in this test method are toxic or corrosive, so, be careful during the operation! If necessary, perform it in a fume hood. If it is splashed on the skin, use water to rinse it immediately. If it is serious, seek medical attention immediately. A.1 General provisions The reagents and water that are used in this Standard, when no other requirements are specified, refer to analytical reagents and grade-III water which is specified in GB/T 6682. The standard titration solution, the standard solutions, preparations and products for impurity determination, which are used in the test, are all prepared in accordance with the provisions of GB/T 601, GB/T 602, and GB/T 603, when no other requirements are specified. The used solution, if not indicated which solvent is used, refers to aqueous solution. A.2 Identification test A.2.1 Reagents and materials A.2.1.1 Hydrochloric acid. A.2.1.2 Nitric acid solution: 1+9. A.2.1.3 Quinoxaline ketone solution. A.2.1.4 Platinum wire ring. A.2.2 Identification method A.2.2.1 Identification of potassium ions Take a small amount, about 0.1 g, of sample; add 10 mL of water to dissolve. Dip a platinum wire ring in hydrochloric acid; burn it to colorless on the flame. Then, dip the test solution and burn it on the flame. The flame shall be purple under observation of the cobalt glass. A.2.2.2 Identification of pyrophosphate Perform the identification of pyrophosphate according to the following method: a) Sample solution: Dissolve 0.1 g of sample in 100 mL of nitric acid solution; b) Second crystallization: Use a small amount of water to heat the first crystallization to dissolve it; cool in a cold water bath to precipitate crystals; pour out the solution; c) Third crystallization: Recrystallize the second crystallization according to the method of the first crystallization; d) Recrystallize sodium pyrophosphate from water three times and place it in a porcelain crucible; then, burn it at 400 °C to a constant mass; e) If using sodium pyrophosphate decahydrate, weigh 80 g and operate according to the first and second crystallization methods. A.3.2.5 Sodium hydroxide standard titration solution: c(NaOH) = 0.1 mol/L; calibrate and calculate according to the following methods: a) Calibration: Weigh about 0.5 g of anhydrous sodium pyrophosphate, accurate to 0.000 2 g; place it in a 250 mL beaker; add 50 mL of water to dissolve. On the acidity meter, slowly add hydrochloric acid solution (A.3.2.1 or A.3.2.2) of an appropriate concentration while stirring, until the pH of the solution is 3.8; add 50 mL of zinc sulfate solution; stir for 5 min. Under stirring, use sodium hydroxide standard titration solution to titrate until the pH of the solution is close to 3.6; stop the titration, stir for 2 minutes to make the solution reach equilibrium; continue the titration; at this time, stir for 30 seconds after each drop is added, until pH is 3.8, as the end point. b) The number of grams per milliliter of sodium hydroxide standard titration solution, which is equivalent to sodium pyrophosphate, is calculated according to Formula (A.1). Where: m – mass of the weighted anhydrous sodium pyrophosphate, in grams (g); V – volume of the sodium hydroxide standard titration solution that is consumed in the titration, in milliliters (mL). A.3.3 Instruments and apparatuses A.3.3.1 Acidity meter: resolution of 0.01 pH, equipped with glass electrode and saturated calomel electrode (or composite electrode). A.3.3.2 Magnetic stirrer. A.4 Determination of loss on ignition A.4.1 Instruments and apparatuses High-temperature furnace: The temperature control range is 800 °C ± 20 °C. A.4.2 Analysis steps Use a porcelain crucible that is previously burned to constant mass at 800 °C ± 20 °C to weigh about 10 g of the sample, accurate to 0.01 g. Place the porcelain crucible that contains the sample in a high-temperature furnace at 800 °C ± 20 °C for 30 minutes; take it out; cool it in a desiccator; weigh it. A.4.3 Result calculation Calculate the mass fraction w2 of loss on ignition according to Formula (A.3). Where: m2 – mass of the porcelain crucible and the sample, in grams (g); m3 – mass of the porcelain crucible and the sample after firing, in grams (g); m4 – sample mass, in grams (g). The test result is based on the arithmetic mean of the parallel determination results. The absolute difference between two independent determination results that are obtained under repeatability conditions is not more than 0.02%. A.5 Determination of water insoluble matter A.5.1 Instruments and apparatuses A.5.1.1 Glass sand crucible: The aperture of the filter plate is 5 μm ~ 15 μm. A.5.1.2 Electrothermal constant-temperature dry box: The temperature control range is 105 °C ± 2 °C. A.5.2 Analysis steps Weigh about 20 g of the sample, accurate to 0.01 g; place it in a 500 mL beaker; add 400 mL of hot water to dissolve; use a glass sand crucible that has been pre-dried at 105 °C ± 2 °C to a constant mass to filter. Use hot water to wash the residue to neutral (use precision pH test paper to test). Place the glass sand crucible in an electrothermal constant-temperature dry box at 105 °C ± 2 °C to dry until the mass is constant. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 1886.340-2021 be delivered?Answer: The full copy PDF of English version of GB 1886.340-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 1886.340-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB 1886.340-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 1886.340-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB 1886.340-2021?A step-by-step guide to download PDF of GB 1886.340-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 1886.340-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
