GB 14681.2-2006 PDF EnglishUS$85.00 · In stock · Download in 9 seconds
GB 14681.2-2006: Electrically heated glazing materials for locomotives and ships - Part 2: Electrically heated glazing materials for locomotives Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB 14681.2-2006: Electrically heated glazing materials for locomotives and ships - Part 2: Electrically heated glazing materials for locomotives---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB14681.2-2006 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 81.040 Q 34 Replacing GB 14681-1993 Electrically heated glazing materials for locomotives and ships - Part 2. Electrically heated glazing materials for locomotives Issued on: FEBRUARY 22, 2006 Implemented on: DECEMBER 1, 2006 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions ... 6 4 Product classification and markings ... 7 5 Material requirements ... 8 6 Service environment ... 8 7 Technical requirements ... 9 8 Test methods ... 13 9 Inspection rules ... 18 10 Symbols, packaging, transportation and storage ... 20ForewordArticles 7.5, 7.6 and 7.7 of this Part are mandatory, while others are recommended. GB 14681 Electrically heated glazing materials for locomotives and ships is divided into two parts. — Part 1. Heated glass panes for ships rectangular windows; — Part 2. Electrically heated glazing materials for locomotives. This Part is Part 2 of GB 14681 Electrically heated glazing materials for locomotives and ships. This Part replaces GB 14681-1993 along with GB 14681.1-2006 Electrically heated glazing materials for locomotives and ships - Part 1. Heated glass panes for ships rectangular windows. The major technical differences between this Part and GB 14681-1993 Electrically heated glazing materials for locomotives and ships are as follows. — ADD two types of glass, namely plane glass and bent glass (SEE Article 4.1.2); — ADD the contrast table for technical requirements and test methods (SEE Table 1); — ADD the requirements for raw materials (SEE Article 5); — ADD the requirements for the deviations in fillet dimension of the glass and in contour dimension of the bent glass (SEE Articles 7.1.1.2 and 7.1.1.3); — CANCEL the performance indicators of optical angular deviation and optical distortion formulated by using the testing method for aircraft glazing materials (SEE Article 5.6.2 of 1993 edition); — ADD the performance indicator of optical distortion formulated by using the testing method for automobile glazing materials (SEE Article 7.5.2); — MAKE provisions on heat resistance according to the testing method for automobile glazing materials and corresponding technical indicators (SEE Articles 7.6.1 and 8.7.1); — ADD the performance indicator and test method of missile resistance Electrically heated glazing materials for locomotives and ships - Part 2. Electrically heated glazing materials for locomotives1 ScopeThis Part specifies the product classification, technical requirements, test methods, inspection rules, symbols, packaging, transportation and storage of the electrically heated glazing materials for the front windows of locomotives and CRH trains (hereinafter referred to as “electrically heated glazing materials”). This Part is applicable to the electrically heated glazing materials for the front windows of locomotives and CRH trains. The electrically heated glazing materials for other parts and windshields can also use this Part as reference. This Part is not applicable to the electrically heated glazing materials for aircraft and ships.2 Normative referencesThe provisions in the following documents become the provisions of this Part through reference in this Part. For dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Part. However, parties who reach an agreement based on this Part are encouraged to study if the latest editions of these documents are applicable. For undated references, the latest editions apply to this Part. GB/T 1214 (all parts) Calipers of vernier type GB/T 1216 External micrometer GB/T 5137.1-2002 Test methods of safety glazing materials used on road vehicles - Part 1. Mechanical properties test (ISO 3537.1999, MOD) GB/T 5137.2-2002 Test methods of safety glazing materials used on road vehicles - Part 2. Optical properties test (ISO 3538.1997, MOD) GB/T 5137.3-2002 Test methods of safety glazing materials used on road vehicles - Part 3. Radiation, high temperature, humidity, fire and simulated weathering resistance tests (ISO 3917.1999, MOD) GB/T 9056 Metal ruler (GB/T 9056-2004, NEQ ISO 5466.80) GB 9656 Safety glazing materials for road vehicles GB 11614 Float glass GB 17841 Tempered and heat-strengthened glass used in curtain walls GJB 500 Aircraft glazing materials - Terms GJB 961-1990 Aircraft - Electrically heated glazing materials - Test methods for electroheat properties GJB 1258-1991 Polyvinyl butyral interlayer GJB 2464-1995 Aircraft glazing materials - Test methods for bird impact3 Terms and definitionsThe terms and definitions defined in GJB 500 and the following ones are applicable to this Part. 3.1 Glazing electrically heated by wire It refers to the electrically heated glazing materials using heating wires as heating elements. 3.2 Glazing electrically heated by film It refers to the electrically heated glazing materials using conductive films as heating elements. 3.3 Mismatch It refers to the mutual offset among layers of glass used for constituting the electrically heated glazing materials. 3.4 Color particle Color particles refer to the colored spot impurities in the cementing layers of the electrically heated glazing materials. 3.5 Busbar B - heat-strengthened glass P - PC board; standard number. 4.2.2 Marking example As for the glazing electrically heated by wire after a piece of 5mm thick tempered glass laminates with a piece of 4mm thick tempered glass, the marking shall be as follows. WL T5 T4 GB 146815 Material requirements5.1 The sheet glass shall comply with the requirements for automobiles of GB 11614. 5.2 The tempered glass shall comply with the requirements of GB 9656. 5.3 The heat-strengthened glass shall comply with the requirements of GB 17841. 5.4 The domestic films using polyvinyl butyral (PVB) shall comply with the requirements of GJB 1258. The imported films shall comply with the requirements for corresponding technical conditions. 5.5 The electrically heated elements (heating wires or metal conductive films) shall comply with the requirements for the technical conditions of ordering. 5.6 PC boards shall comply with the requirements for the technical conditions of corresponding products.6 Service environment6.1 The electrically heated glazing materials shall be used under the conditions that the ambient temperature is within the range of -50°C to 70°C and the temperature difference inside and outside the glass is not greater than 65°C. 6.2 There shall be sinusoidal vibration with a frequency within the range of 1Hz to 50Hz corresponding to the vertical and longitudinal directions of the locomotives. Under normal circumstances, the vibration acceleration shall not be greater than 3 m/s2. The short-term repetitive vibration acceleration shall not 7.8.1 Actual total power or heating element resistance The test shall be conducted according to Article 8.9.1. The actual total power or heating element resistance shall conform to the design requirements. However, it is allowed to have an error of 10% or be agreed upon by the supplier and demander. 7.8.2 Insulation resistance The test shall be conducted according to Article 8.9.1. The insulation resistances among the insulation positions shall not be less than 50MΩ. 7.8.3 Electrothermal impact resistance The test shall be conducted according to Article 8.9.2. After withstanding 2h at -50°C ± 2°C, ELECTRIFY for 15min according to the product requirements. After the test, the glass shall still be able to function properly. Furthermore, the appearance quality shall still conform to the provisions of Article 7.4. 7.8.4 Electric heating resistance The test shall be conducted according to Article 8.9.3. APPLY 1.2 times the rated voltage at 20°C ± 5°C. OPERATE for 30min. After the test, the glass shall still be able to function properly. Furthermore, the appearance quality shall still conform to the provisions of Article 7.4. 7.8.5 Heating uniformity When conducting the test according to Article 8.9.4, the wax melting time of the glass shall not be greater than 10min, or the temperature differences among various points in the heating areas shall not be greater than 10°C.8 Test methods8.1 Measurement of contour dimensions USE a steel ruler or steel tape with a minimum scale of 1mm, which conforms to the provisions of GB/T 9056, to measure the contour dimensions of the products. If the user provides templates, it is allowed to inspect based on the templates. 8.2 Thickness measurement USE an external micrometer with a minimum ... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 14681.2-2006 be delivered?Answer: The full copy PDF of English version of GB 14681.2-2006 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 14681.2-2006_English with my colleagues?Answer: Yes. The purchased PDF of GB 14681.2-2006_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 14681.2-2006 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB 14681.2-2006?A step-by-step guide to download PDF of GB 14681.2-2006_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 14681.2-2006". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
