GB/T 11313.1-2013 English PDFUS$1534.00 · In stock
Delivery: <= 5 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 11313.1-2013: Radio-frequency connectors -- Part 1: Generic specification -- General requirements and measuring methods Status: Valid GB/T 11313.1: Historical versions
Basic dataStandard ID: GB/T 11313.1-2013 (GB/T11313.1-2013)Description (Translated English): Radio-frequency connectors -- Part 1: Generic specification -- General requirements and measuring methods Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L23 Classification of International Standard: 33.120.30 Word Count Estimation: 77,763 Older Standard (superseded by this standard): GB/T 11313-1996; GB/T 11313.1-2000 Quoted Standard: GB/T 2421.1-2008; GB/T 2423.1-2008; GB/T 2423.2-2008; GB/T 2423.3-2006; GB/T 2423.4-2008; GB/T 2423.5-1995; GB/T 2423.6-1995; GB/T 2423.10-1995; GB/T 2423.17-2008; GB/T 2423.18-2012; GB/T 2423.21-2008; GB/T 2423.22-2002; GB/T 2423.28-2005; GB/T 2423.32-20 Adopted Standard: IEC 61169-1-1998, IDT Regulation (derived from): National Standards Bulletin No. 22 of 2013 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the general requirements for radio frequency connectors and test methods. This section applies to communications, electronic equipment and similar equipment in connection with the RF transmission line. GB/T 11313.1-2013: Radio-frequency connectors -- Part 1: Generic specification -- General requirements and measuring methods---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Radio-frequency connectors Part 1. Generic specification General requirements and measuring methods ICS 33.120.30 L23 National Standards of People's Republic of China Replacing GB/T 11313-1996, GB/T 11313.1-2000 RF Connectors Part 1. Generic specification - General requirements and test methods Part 1. Genericspecification-Generalrequirementsandmeasuringmethods (IEC 61169-1.1998, IDT) Issued on. 2013-11-12 2014-04-15 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ 1 Scope 1 2 Objective 1 3 Normative references 1 4 Terms and definitions 2 4.1 connector part 2 generic term Basic terms 4.2 connector 3 4.3 The term structure 4 4.4 Seal 5 4.5 Other terms and related terms 5 measuring equipment 4.6 General Electrotechnical terminology 6 5 units, symbols, and size 7 5.1 Units and Symbols 7 5.2 Size 7 6 standard ratings and characteristics 7 7 climate classification 8 8 IEC model named 8 9 Test methods 8 9.1 Overview 8 9.2 electrical test and measurement procedures 10 9.3 Mechanical tests and test procedures 39 9.4 climatic conditions tried and tested 47 9.5 Mechanical durability 52 9.6 high-temperature durability 52 9.7 Resistance to solvents and contaminating fluids 53 10 54 quality assessment 10.1 Overview 54 Quality assessment procedures 54 10.2 Test and measurement procedures 56 10.3 Norms and procedures 61 10.4 11 62 Flag 62 11.1 element flag 11.2 Packing logo and content 62 (Nautical environment 9.4.6.2 provisions) Appendix A (normative) for the salt spray test simulated sea water 64 Annex B (informative) documents 65 Annex C (informative) determine cable retention tensile strength test to be applied and the torque guidelines and some typical cable Recommended value 66 Annex D (informative) Model name 71ForewordGB/T 11313 "RF connector" is divided into the following sections. --- Part 1. Generic specification - General requirements and test methods --- Part 2. 9.52 RF coaxial connector specification This section GB/T 11313 Part 1. This section drafted in accordance with GB/T 1.1-2009 given rules. This Part replaces GB/T 11313-1996 "RF connectors - Part 1. Generic specification - General requirements and test methods" GB/T 11313.1-2000 "RF connectors - Part 1-1. Blank detail specification for single or multi-family." This portion of the GB/T 11313-1996, compared the main technical changes are as follows. --- Increase the "d) When the mating cable connector continuity measurement, care should be taken to avoid the thermal coefficient of resistance of the cable And produce erroneous results. "(See 9.2.3.4) --- Added "safety wire hole strength" (see 9.3.15). --- Added "fixed number of sampling procedures and inspection requirements of the test schedule" (see 10.3.3). --- Added Appendix C (informative) determine cable retention tensile strength test to be applied and the torque guidelines and some typical Recommended cable (see Appendix C). --- Increasing the type designation (see Appendix D). This section compared with the GB/T 11313.1-2000 main technical changes are as follows. --- Remove the GB/T 11313.1 of the entire contents. This section uses the translation method is equivalent to using IEC 61169-1.1998 "RF connectors - Part 1. Generic specification - General requirements and test method". This part made the following editorial changes. --- "9.1 Overview" in paragraph 4, "Group Test table as shown in Appendix A" to "test group See Table 10.3.2.3". --- "9.1.2 visual inspection", the "flag shall comply with the provisions of 11.2" with the words "flag shall comply with the provisions of 11.1." --- The "9.2.1.7.2 error-free recognition methods comply with the provisions of 9.2.1.1" with "9.2.1.7.2 and 9.2.1.4 accord The method of the error-free identification of the provisions of 9.2.1.5. " --- The "9.2.1.7.3 erroneous recognition methods comply with the provisions of 9.2.1.4" with "9.2.1.7.3 in line with 9.2.1.6 Regulation Given a margin of error recognition method. " --- IEC 61169-1.1998 number of tables in a lot of confusion, this section of the table numbers were corrected. Increasing the model name (see Appendix D). Consistency correspondence between this part of international documents and normative references of our files are as follows. --- GB/T 2423.23-1995 Environmental testing for electric and electronic products Test Q. Sealing (eqv IEC 60068-2-17. 1978); --- GB/T 2987-1996 Parameters symbol tube (neqIEC 60027-1.1992, IEC 60027-2. 1972); --- GB 3100-1993 International System of Units and Its Application (eqv ISO 1000.1992); --- GB/T 14313-1993 Precision hard coaxial cable and precision connector Generic specification (eqv IEC 60457-1. 1974); --- GB/T 15396-1994 RF cables and connectors for hexagonal and square die cavities, indentors, gauges, outer conductor crimp Sleeves and center contact crimp wire barrel dimensions (eqv IEC 60803. 1984). Please note that some of the content of this section may involve patents. This part of the release mechanism does not assume the responsibility to identify these patents. This part is proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This section is under the jurisdiction of the National electronic equipment with a high-frequency cables and connectors Standardization Technical Committee (SAC/TC190). This section drafted by. China Electronics Standardization Institute. The main drafters of this section. Wu Zhengping, Qiao Changhai, Guo Yan, Wuxiang Wen, Liu, Chen Guohua. This part of the standard replaces the previous editions are. --- GB/T 11313-1996; --- GB/T 11313.1-2000. RF Connectors Part 1. Generic specification - General requirements and test methods1 ScopeGB/T 11313 provisions of this part of the RF connector General requirements and test methods. This section applies to communications, electronic equipment and similar equipment in connection with the RF transmission line. Objective 2 As a general norm in this part, it is to develop each connector specification basis. Its purpose is to establish uniform following concepts and procedures. ---the term; --- Standard ratings and characteristics; --- Electrical and mechanical properties of test and measurement procedures; --- Environmental testing procedures by temperature, humidity and vibration divided connector category. This section of the test methods and procedures applicable to the identification and recognition of approval test. When agreed between manufacturer and user, this section It can also be used as the basis of the acceptance tests.3 Normative ReferencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 2421.1-2008 Environmental testing for electric and electronic products overview and guidance (IEC 60068-1. 1988, IDT) GB/T 2423.1-2008 Environmental testing for electric and electronic products Part 2. Test methods Test A. Cold (IEC 60068-2-1. 2007, IDT) GB/T 2423.2-2008 Environmental testing for electric and electronic products Part 2. Test methods Test B. Dry heat (IEC 60068-2-2. 2007, IDT) GB/T 2423.3-2006 Environmental testing for electric and electronic products Part 2. Test methods - Test Cab. Damp heat test (IEC 60068-2-78.2001, IDT) GB/T 2423.4-2008 Environmental testing for electric and electronic products Part 2. Test methods - Test Db alternating hot and humid (12h 12h cycle) (IEC 60068-2-30.2005, IDT) GB/T 2423.5-1995 Environmental testing for electric and electronic products Part 2. Test methods Test Ea and guidance. Shock (Idt IEC 60068-2-27. 1987) GB/T 2423.6-1995 Environmental testing for electric and electronic products Part 2. Test methods - Test Eb and guidance. Bump (Idt IEC 60068-2-29. 1987) GB/T 2423.10-1995 Environmental testing for electric and electronic products Part 2. Test methods Test Fc. Vibration (sinusoidal) (Idt IEC 60068-2-6. 1982) GB/T 2423.17-2008 Environmental testing for electric and electronic products Part 2. Test methods - Test Ka. Salt (IEC 60068- 2-11. 1981, IDT) GB/T 2423.18-2012 Environmental testing for electric and electronic products Part 2. Test methods - Test Kb. Salt mist, cyclic (chloride ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 11313.1-2013_English be delivered?Answer: Upon your order, we will start to translate GB/T 11313.1-2013_English as soon as possible, and keep you informed of the progress. The lead time is typically 3 ~ 5 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 11313.1-2013_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 11313.1-2013_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 11313.1-2013?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 11313.1-2013 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
