JJF 1002-2010 (JJF1002-2010) & related versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | See Detail | Status | Similar PDF |
| JJF 1002-2010 | English | 759 |
Add to Cart
|
6 days
|
The Rules for Drafting National Metrological Verification Regulation
|
JJF 1002-2010
| Valid |
JJF 1002-2010
|
| JJF 1002-1998 | English | RFQ |
ASK
|
6 days
|
The Rules for Drafting National Metrological Verification Regulation
|
JJF 1002-1998
| Obsolete |
JJF 1002-1998
|
| JJF 1002-1984 | English | RFQ |
ASK
|
3 days
|
(Chinese Industry Standard)
|
JJF 1002-1984
| Obsolete |
JJF 1002-1984
|
JJF 1002-2010: PDF in English
JJF 1002-2010
The Rules for Drafting National Metrological Verification Regulation
People's Republic of China National Metrology Technical Specifications
State verification procedures to write rules
Issued on. 2010-09-06
2011-01-01 implementation
The State Administration of Quality Supervision, Inspection and Quarantine released
State verification procedures to write rules
ulation
Replacing JJF 1002-1998
Focal point. the National Technical Committee of Legal Metrology measurement management
The main drafting units. State Administration of Quality Supervision, Inspection and Quarantine Division metering
China Institute of Metrology
Participated in the drafting unit. China Metrology Association
This specification commissioned the National Technical Committee on Metering Management is responsible for interpretation of legal metrology
The main drafters of this specification.
Chen Hong (State Administration of Quality Supervision, Inspection and Quarantine Measurement Department)
Chen Xin (China Institute of Metrology)
Drafters participate.
Luo Xinyuan (China Metrology Association)
table of Contents
Introduction (Ⅲ)
1 Scope (1)
2. References (1)
3 General (1)
3.1 General principles of procedure prepared by (1)
3.2 Basic requirements expressed procedures (1)
Procedures structure 4 (2)
5 procedures contents of each section (2)
5.1 Cover (2)
5.2 title page (2)
5.3 Directory (2)
5.4 Introduction (2)
Range 5.5 (3)
5.6 reference document (3)
5.7 Terms and units of measurement (3)
5.8 Overview (3)
5.9 Measurement Performance requirements (3)
5.10 General Requirements (3)
5.11 Control of measuring instruments (3)
5.12 Appendix (5)
6 level classification (5)
6.1 (5)
6.2 (5)
6.3 (5)
6.4 Appendix (6)
Edit Rule 7 (6)
7.1 Footnote (6)
7.2 The provisions of note (6)
Table 7.3 Notes and Legend (6)
7.4 Item Description (6)
Table 7.5 (7)
Figure 7.6 (7)
7.7 reference (8)
7.8 Mathematical Formula (9)
7.9 numerical expression (9)
Acronyms 7.10 (9)
7.11 value and unit labels (9)
7.12 simplified Chinese characters and punctuation marks (9)
7.13 Book brow line (10)
7.14 End of Line (10)
7.15 procedures and font size (10)
Appendix A Quantities and units (11)
Appendix B cover and back cover format (13)
Appendix C title page format (15)
Appendix D procedures and font size (17)
Appendix E hierarchical numbering example (18)
Examples Appendix F Provisions arrangement (19)
Appendix G calibration certificate/test results in the notice page and format (23)
introduction
JJF 1002 "national verification procedures write rules", JJF 1001 "common measurement terms and definitions"
JJF 1059 "Evaluation and Expression of Uncertainty in Measurement" common procedure constitutes a support revision of the basic series
specification.
JJF 1002 "national verification procedures to write rules" is the International Organization of Legal Metrology (OIML) skilled workers
Guidelines for Part 2 of "drafting and presentation of the rules of international recommendations and international instruments" in English (DIRECTIVES
FORTHE TECHNICAL WORK, Part 2. Guidetothedraftingandpresentation
OIMLInternationalRecommendationsandDocuments), based on the version JJF 1002-1998
Subject to revisions. Compared with JJF 1002-1998, in addition to editorial changes outside the main technical changes are as follows.
--- Introduction to the essential content, increasing the introduction of content requirements (see 5.4);
--- Canceled a rule of international recommendations written form requirements;
--- Clear "reference document" means the introduction of a date reference files are not dated references to
Request (see 5.6);
--- Increased in terms of form and content of the specific requirements (see 5.7);
--- Stressing that this rule does not involve the content type evaluation (see 5.11), and delete the original rule "shape identification
Or prototype test, "this one (see 5.11);
--- Refine the test conditions (see 5.11.1.1);
--- Added "test certificate/test results within the notice page and Format" appendix (Appendix G);
--- Remove the original rules "error analysis example" appendix.
JJF 1002─1998 of previously issued as follows.
--- JJF 1002─1984.
State verification procedures to write rules
1 Scope
This rule applies to the preparation of national verification procedures (hereinafter referred to as Regulations). Author departments and verification procedures
Local verification procedures can be measured with reference to use.
2. References
This rule references the following documents.
GB 3102.1 and the amount of space and time units
GB/T 14691 Technical Drawing Font
GB/T 15834 Streetwise
GB/T 15835-1995 provisions on the publication of digital usage
Part of GB/T 20001.1 standard rules for the preparation of 1. Terminology
GB/T 1.1-2009 for standardization Part I. The structure and preparation of standards
For dated references, only the dated edition applies to this rule; undated reference documents
Member, the latest edition (including any amendments) apply to this rule.
3 General
3.1 General principles written procedure
National verification procedures for assessing the characteristics of measuring instruments, organized by the metrological administrative department of the State Council formulated and approved
Published in the nationwide implementation, technical documents as measuring instruments to determine the legal status. To this end, procedures should be done
--- Compliance with relevant laws and regulations of the country;
--- The scope must be clearly within the scope of their defined, and strive to complete as necessary;
--- The requirements of scientific and reasonable, taking into account the feasibility and economic implementation of the operation;
--- According to national circumstances, active use of international recommendations of the International Organization of Legal Metrology (OIML) released international documents
And international standards of relevant international organizations (such as ISO , IEC , etc.) released.
Basic requirements 3.2 Regulations expressed
--- Textual representation should be done structured, structured, precise wording, clear narrative, without produce different
understanding;
--- The term, symbols, codes, abbreviations should be unified, and always express the same concept;
--- Expressed in units of measurement according to the state names and symbols, names and symbols of the amount of error and measurement uncertainty
Names and symbols;
--- Formulas, drawings, tables, data should be expressed accurately as required;
--- Presentation on the contents related regulations should be consistent, not contradictory.
......
| Standard ID | JJF 1002-2010 (JJF1002-2010) | | Description (Translated English) | The Rules for Drafting National Metrological Verification Regulation | | Sector / Industry | Metrology & Measurement Industry Standard | | Classification of Chinese Standard | A50 | | Classification of International Standard | 17.020 | | Word Count Estimation | 33,339 | | Date of Issue | 2010-09-06 | | Date of Implementation | 2011-03-06 | | Older Standard (superseded by this standard) | JJF 1002-1998 | | Quoted Standard | GB 3102.1; GB/T 14691; GB/T 15834; GB/T 15835-1995; GB/T 20001.1; GB/T 1.1-2009 | | Adopted Standard | DIRECRIVES FOE THE TECHNICAL WORK PART 2, NEQ | | Drafting Organization | State Administration of Quality Supervision, Inspection and Quarantine Measurement Department | | Administrative Organization | National Technical Committee of Legal Metrology management | | Regulation (derived from) | AQSIQ Announcement No. 100 of 2010 | | Issuing agency(ies) | State Administration of Quality Supervision, Inspection and Quarantine | | Summary | This standard applies to the preparation of national metrological verification regulations (hereinafter referred to as rules). Preparation of departmental metrological verification and verification procedures may refer to local use. |
|