Powered by Google www.ChineseStandard.net Database: 189759 (7 Jul 2024)

GB/T 9985-2022 related PDF English

GB/T 9985-2022 (GB/T9985-2022, GBT 9985-2022, GBT9985-2022) & related versions
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)See DetailStatusSimilar PDF
GB/T 9985-2022English170 Add to Cart 0-9 seconds. Auto delivery. Detergents for hand dishwashing GB/T 9985-2022 Valid GBT 9985-2022
GB 9985-2000English919 Add to Cart 4 days [GB/T 9985-2000] Detergents for hand dishwashing GB 9985-2000 Obsolete GB 9985-2000
GB 9985-1988EnglishRFQ ASK 3 days Dishwashing detergents GB 9985-1988 Obsolete GB 9985-1988
Buy with any currencies (Euro, JPY, KRW...): GB/T 9985-2022    Preview this PDF: GB/T 9985-2022

GB/T 9985-2022: PDF in English (GBT 9985-2022)
GB/T 9985-2022
ICS 71.100.40
CCS Y 43
Replacing GB/T 9985-2000
Detergents for Hand Dishwashing
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative References ... 5
3 Terms and Definitions ... 6
4 Requirements ... 6
5 Test Methods ... 7
6 Inspection Rules ... 7
7 Marking, Packaging, Transportation and Storage ... 8
Appendix A (normative) Determination of Detergency ... 9
Detergents for Hand Dishwashing
1 Scope
This document specifies the requirements, test methods, inspection rules, as well as marking,
packaging, transportation and storage of detergents for hand dishwashing.
This document is applicable to detergents for hand dishwashing formulated with surfactants
and auxiliaries and detergents for hand dishwashing with the function of fruit and vegetable
2 Normative References
The contents of the following documents constitute indispensable clauses of this document
through the normative references in the text. In terms of references with a specified date, only
versions with a specified date are applicable to this document. In terms of references without a
specified date, the latest version (including all the modifications) is applicable to this document.
GB/T 1535 Soya Bean Oil
GB/T 6368 Surface Active Agents - Determination of pH of Aqueous Solution - Potentiometric
GB/T 6682 Water for Analytical Laboratory Use - Specification and Test Methods
GB/T 8937 Edible Lard
GB/T 13173-2021 Surface Active Agents - Test Methods for Detergents
GB/T 13529 Sodium Ethoxylated Alkyl Sulfate
GB/T 15818 Test Method for Biodegradability of Surfactants
GB/T 21801 Chemicals - Ready Biodegradability - Manometric Respirometry Test
GB/T 21802 Chemicals - Ready Biodegradability - Modified MITI Test (I)
GB/T 21803 Chemicals - Ready Biodegradability - DOC Die-away Test
GB/T 21831 Chemicals - Ready Biodegradability: Closed Bottle Test
GB/T 21856 Chemicals - Ready Biodegradability - CO2 Evolution Test
GB/T 21857 Chemicals - Ready Biodegradability - Modified OECD Screening Test
Appendix A
Determination of Detergency
A.1 Oil Removal Rate Method (arbitration method)
A.1.1 Principle
Evenly apply standard artificial dirt on the glass slide, use a dishwashing detergent solution
with a certain concentration to wash it under specified conditions, and determine the percentage
of oily dirt removal.
NOTE: the oil removal rate method is applicable to dishwashing detergents of various formulas.
A.1.2 Reagents and materials
The used reagents and materials are as follows:
a) Hydrochloric acid, V (HCl) : V (H2O) = 1 : 6 solution;
b) Sodium hydroxide, 50 g/L solution;
c) Absolute ethanol;
d) Urea;
e) Glyceryl monostearate (40%);
f) Calcium chloride (CaCl2);
NOTE 1: calcium chloride with a certain hydration number may also be used, but in specific use,
it needs to be converted in accordance with the amount of calcium chloride (CaCl2)
stipulated in A.1.2m).
g) Magnesium chloride (MgCl2  6H2O);
NOTE 2: anhydrous magnesium chloride or magnesium chloride with a certain hydration number
may also be used, but in specific use, it needs to be converted in accordance with the
amount of magnesium chloride (MgCl2  6H2O) stipulated in A.1.2m).
h) Refined butter;
i) Refined lard: edible lard (GB/T 8937);
j) Refined vegetable oil: soya bean oil (GB/T 1535);
k) Sodium alkylbenzene sulfonate;
l) Sodium ethoxylated alkyl sulfate (C12 ~ C14, EO 2 ~ 3, GB/T 13529);
m) 250 mg/L hard water: weigh-take 16.70 g of calcium chloride and 20.37 g of
magnesium chloride to prepare 10 L, about 2,500 mg/L hard water. During use, take
1 L and dilute to 10 L, that is, 250 mg/L hard water.
A.1.3 Instruments, equipment and utensils
The used instruments and equipment are as follows:
a) Balance: with a division value of 0.2 g;
b) Balance: with a division value of 0.1 mg;
c) Electromagnetic heating stirrer;
d) Vertical-type detergency testing machine and corresponding complete set of
e) Thermometer: with a measuring range of 0 C ~ 100 C (maximum allowable error 
0.2 C), 0 C ~ 200 C (maximum allowable error  2 C);
f) Glass slide for microscope: 2 mm  76 mm  26 mm;
g) Tweezers, clips;
h) Enamel tray: 300 mm  400 mm;
i) Tall beaker: 100 mL;
j) Constant-temperature water bath.
A.1.4 Test
A.1.4.1 Preparation of standard dishwashing detergent
In accordance with the mass ratio, respectively weigh-take 14 portions of sodium alkylbenzene
sulfonate (counted by 100%), 1 portion of ethoxylated alkyl sodium sulfate (counted by 100%),
5 portions of absolute ethanol and 5 portions of urea; add water to 100 portions and mix it well;
use hydrochloric acid or sodium hydroxide to adjust pH to 7 ~ 8 and reserve it for later use.
A.1.4.2 Preparation of mixed oil stain
In accordance with the mass ratio, respectively weigh-take 5 portions of butter, 5 portions of
lard, 10 portions of vegetable oil and 1 portion of glyceryl monostearate, and place in a beaker.
On an electric furnace, heat it to 180 C to melt, and through electromagnetic stirring, maintain
at this temperature for 10 min. After natural cooling, store it in the refrigerator for later use; the
shelf life is 6 months.
A.1.4.3 Preparation of smeared slides
A. Environmental conditions
The whole process of smeared slide preparation shall maintain at room temperature of (22  3)
C and a relative humidity of (50  10) % (that is, the selection or adjustment of environmental
conditions during the test is based on the principle of obtaining smeared slides that comply with
the requirements).
A. Preparation of glass slides
Newly purchased glass slides need to be boiled in a detergent solution for 15 min, washed with
clean water, until no water droplets hang on them, then, soaked in chromic acid cleansing
solution for 1 h, rinsed with clean water and washed with distilled water, then, dried and stored
in a drying oven.
Mark the serial No. on each slide and draw a line 10 mm away from the upper edge of the slide
to show that that the smear is below this line; draw a line 5 mm from the bottom edge of the
slide to show that the excess oil stain below this line shall be wiped off.
Weigh-take the mass of each glass slide (accurate to 1 mg); use the prepared clips to clamp the
glass slides of known mass one by one along the line and above, then, hang them on the drying
rack and place the drying rack in the enamel tray to prepare for smearing.
A. Smearing of glass slides
Take an appropriate amount of the prepared mixed oil stain and place it in a constant-
temperature water bath to maintain the oil temperature at (50  2) C.
Remove the glass slides, together with the clips, from the drying rack one by one; hold the clips
and slowly immerse the slides in the oil stain at an oil temperature of (50  2) C to 10 mm
below the upper line, then, slowly take them out, repeat this for 2 ~ 3 times; after the last
smearing, when the dripping of the oil stain slows down, hang the smeared slides back to the
original drying rack and successively prepare the smeared slides; after the oil stain on the glass
slides becomes solidified, firstly use filter paper or absorbent cotton to wipe off the excess oil
stain on the bottom edge and both sides of the lower edge of the smeared slides at 5 mm, then,
use tweezers to hold the absorbent cotton dipped in absolute ethanol or petroleum ether to wipe
them clean, and let them dry for 3 h under the environmental conditions required by this test;
move the air-dried smeared slides to a weighing rack and use an analytical balance to accurately
weigh the mass of each smeared glass slide; the amount of smearing for each slide shall be
controlled at (0.13  0.02) g, every 4 slides shall be a group, and the amount of smearing for
each group of slides shall be controlled at (0.50  0.05) g.
A.1.4.4 Test procedures
m2---the mass of the smeared slide after washing, expressed in (g).
b) Precision
The relative mean deviation of the two groups of results  5%.
c) Detergency evaluation
Take the arithmetic mean of the ratio of the oil removal rate of the specimen to the oil
removal rate of the standard dishwashing detergent as the test result. When the ratio
of oil removal rate is greater than 1.05, it shall be determined that the detergency is
greater than that of the standard dishwashing detergent; when the ratio of oil removal
rate is less than 0.95, it shall be determined that the detergency is less than that of the
standard dishwashing detergent; when the ratio of oil removal rate is greater than or
equal to 0.95, and less than or equal to 1.05, it shall be determined that the detergency
is equal to that of the standard dishwashing detergent.
A.2 Foam Level Method
A.2.1 Principle
Apply a certain amount of artificial dirt on the dishes and wash them in a dishwashing detergent
solution of a specified concentration. Since the dirt washed can eliminate the foam of the
washing solution, and the number of dishes (i.e. the amount of dirt) that can be cleaned by each
detergent solution is related to its detergency, take the surface foam layer disappearing to half
as the end point of washing and the number of dishes washed as the evaluation of detergency.
NOTE: the foam level method is not applicable to the determination of the detergency of low-
foaming dishwashing detergents.
A.2.2 Reagents and materials
The used reagents and materials are the same as A.1.2, plus the following items:
a) whole milk powder;
b) wheat flour;
c) fresh eggs.
A.2.3 Instruments, equipment and utensils
The used instruments and equipment are as follows.
a) Desk-type balance: with a division value of 0.1 g.
b) White enamel basin: the diameter of the upper opening is 45 cm and the volume is 8
c) White porcelain dish: the water absorption rate is not more than 1%; under natural
light, through visual inspection, the glaze surface shall not manifest obvious color
difference, pores, spots or cracks. There are three specifications: large, medium and
small. The outer diameter of the large dish is about 250 mm, and the diameter of the
smeared part of the bottom of the dish is not less than 160 mm; the outer diameter of
the medium dish is about 200 mm, and the diameter of the smeared part of the bottom
of the dish is not less than 120 mm; the outer diameter of the small dish is about 160
mm, and the diameter of the smeared part of the bottom of the dish is not less than
100 mm.
d) Bristle paint brush: with a width of 38 mm and 102 mm.
e) Tubulated bottle: 5,000 mL.
f) Beaker: 150 mL.
g) Measuring cylinder: 1,000 mL.
h) Stopwatch.
A.2.4 Preparation of artificial dirt
Formula of artificial dirt (mass ratio): 15% mixed oil, 15% wheat flour, 7.5% whole milk
powder, 30% fresh whole egg liquid and 32.5% distilled water.
In accordance with the number of smeared dishes, determine the amount of dirt prepared; in
accordance with the above-mentioned formula ratio, weigh each component.
Shell the fresh eggs and put them in a beaker, evenly stir it and reserve for later use; evenly mix
the wheat flour and whole milk powder and reserve for later use; put the mixed oil in a beaker
and heat to 50 C ~ 60 C to melt, transfer the evenly mixed wheat flour and whole milk powder
into the beaker with melted mixed oil and stir. By several times, add water at 35 C to the beaker
and evenly stir it, then, by several times, add the fresh egg liquid to the beaker and stir it, until
it manifests fine and smooth artificial dirt, which is ready to be used for smearing (prepare right
before use).
A.2.5 Preparation of smeared dishes
Put the prepared dirt and a 38 mm wide bristle paint brush on a desk-type balance to weigh; use
the subtraction method to control the amount of dirt and apply it to the dish one by one. The
amount of dirt smeared is 4 g on the large dish, 2 g on the medium dish and 0.8 g on the small
dish. If the large dish is used as the unit, then, one medium dish is equivalent to 0.5 large dish,
and one small dish is equivalent to 0.2 large dish.
During smearing, use the bristle paint brush to dip the artificial dirt and evenly apply it on the
concave center surface of the dish. After smearing, place at room temperature 20 C ~ 25 C
overnight for 12 h ~ 16 h.

Standard ID GB/T 9985-2022 (GB/T9985-2022)
Description (Translated English) Detergents for hand dishwashing
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard Y43
Classification of International Standard 71.100.40
Word Count Estimation 14,193
Date of Issue 2022-12-30
Date of Implementation 2024-01-01
Older Standard (superseded by this standard) GB/T 9985-2000
Drafting Organization China Research Institute of Daily Chemistry Co., Ltd., Guangzhou Blue Moon Industrial Co., Ltd., Shanghai Kaimi Technology Co., Ltd., Guangzhou Liby Enterprise Group Co., Ltd., Guangzhou Langqi Industrial Co., Ltd., Shanghai Hehuang Baimao Co., Ltd., Wei Lai ( Guangzhou) Commodity Co., Ltd., Shenzhen Baggme Biotechnology Co., Ltd., Infinitus (China) Co., Ltd., Amway (China) Commodity Co., Ltd., Beijing Reward Daily Chemical Co., Ltd., Guangdong Keling Chemical Cleaning Technology Co., Ltd., Zhongshan Lanju Daily Chemical Industry Co., Ltd., China Light Daily Chemical Inspection and Certification Co., Ltd.
Administrative Organization National Standardization Technical Committee of Food Cleaning and Disinfection Products (SAC/TC 395)
Proposing organization State Administration for Market Regulation, National Standardization Management Committee