GB/T 7323-2019 (GB/T7323-2019, GBT 7323-2019, GBT7323-2019) & related versions
Buy with any currencies (Euro, JPY, KRW...): GB/T 7323-2019 Preview this PDF: GB/T 7323-2019
GB/T 7323-2019: PDF in English (GBT 7323-2019)
GB/T 7323-2019
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 75.100
E 36
Replacing GB/T 7323-2008
Extreme pressure lithium lubricating grease
极压锂基润滑脂
ISSUED ON: OCTOBER 18, 2019
IMPLEMENTED ON: MAY 01, 2020
Issued by: State Administration for Market Regulation;
Standardization Administration of the People's Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Classification and marking ... 5
4 Requirements and test methods ... 5
5 Inspection rules ... 6
6 Marking, packaging, transportation, storage and delivery acceptance ... 8
Extreme pressure lithium lubricating grease
1 Scope
This Standard specifies the classification and marking, requirements and test
methods, inspection rules and marking, packaging, transportation and storage
of extreme pressure lithium lubricating grease made from fatty acid lithium soap
thickened lubricating oil and added with antioxidant and extreme pressure
additives.
This Standard applies to lubricating grease for bearings and gears of high-load
machinery and equipment with operating temperatures ranging from -20°C ~
120°C. It also applies to lubricating grease for centralized lubrication systems.
2 Normative references
The following referenced documents are indispensable for the application of
this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any
amendments) applies.
GB/T 269 Lubricating grease and petrolatum - Determination of cone
penetration
GB/T 4929 Lubricating grease - Determination of dropping point
GB/T 5018 Standard test method for determining corrosion preventive
properties of lubricating greases
GB/T 7325 Petroleum products - Lubricating greases and oils -
Determination of evaporation loss
GB/T 7326 Lubricating grease - Corrosiveness to copper - Copper strip test
SH/T 0048 Determination of similar viscosity of lubricating greases
SH/T 0109 Petroleum products and lubricants - Determination of water
washout characteristics of lubricating greases
SH/T 0164 Petroleum and related products packaging, storage,
transportation and acceptance of delivery rules
5.1.1 Factory-exit inspection
Factory-exit batch inspection items include: work cone penetration, dropping
point, corrosion, oil separation and extreme pressure performance (four-ball
machine method) PB.
Factory-exit cycle inspection items include: evaporation loss, impurity, similar
viscosity, extended work cone penetration, water washout loss and oxidation
stability, which are inspected every six months; corrosion resistance, extreme
pressure performance (Timken method) OK value and low temperature torque,
which are inspected once a year.
5.1.2 Type inspection
Type inspection items include all the items in Table 1. Type inspection shall be
carried out in one of the following cases:
a) When a new product is put into production or when product type
identification;
b) When major changes in raw materials, processes, etc., may affect product
quality;
c) When there is a big difference between the factory-exit inspection result
and the last type inspection result.
5.2 Batching
Under the condition of the same raw materials and technology, each can or
kettle is a group (batch).
5.3 Sampling
Sampling is carried out according to SH/T 0229. 4 kg is taken for inspection
and as retention samples.
5.4 Determination rules
If the factory-exit inspection and type inspection results meet the requirements
of Table 1, the batch of products is determined to be qualified.
5.5 Re-inspection rules
If the factory-exit inspection results do not meet the requirements of Table 1, it
shall take double quantity of samples for re-inspection according to the
provisions of SH/T 0229. If there are still non-conforming items in the re-
inspection results, the batch of products shall be determined unqualified.
......
| Standard ID | GB/T 7323-2019 (GB/T7323-2019) | | Description (Translated English) | Extreme pressure lithium lubricating grease | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | E36 | | Classification of International Standard | 75.100 | | Word Count Estimation | 6,613 | | Date of Issue | 2019-10-18 | | Date of Implementation | 2020-05-01 | | Drafting Organization | China Petroleum & Chemical Corporation Petrochemical Research Institute | | Administrative Organization | National Standardization Technical Committee of Petroleum Products and Lubricants (SAC/TC 280) | | Proposing organization | National Standardization Technical Committee of Petroleum Products and Lubricants (SAC/TC 280) | | Issuing agency(ies) | State Administration for Market Regulation, China National Standardization Administration |
|