Powered by Google www.ChineseStandard.net Database: 189759 (14 Jul 2024)

GB/T 4346-2008 related PDF English

GB/T 4346-2008 (GB/T4346-2008, GBT 4346-2008, GBT4346-2008) & related versions
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)See DetailStatusSimilar PDF
GB/T 4346-2008English130 Add to Cart 0-9 seconds. Auto delivery. Machine tools -- Manually operated self-centering chucks GB/T 4346-2008 Valid GBT 4346-2008
GB/T 4346.1-2002English639 Add to Cart 5 days Self-centring manually operated chucks for machine tools -- Part 1: Dimensions and specifications GB/T 4346.1-2002 Obsolete GBT 4346.1-2002
GB/T 4346-1984English399 Add to Cart 3 days 3-jaw self-centering chucks--Dimensions GB/T 4346-1984 Obsolete GBT 4346-1984
Buy with any currencies (Euro, JPY, KRW...): GB/T 4346-2008    Preview this PDF: GB/T 4346-2008

GB/T 4346-2008: PDF in English (GBT 4346-2008)
GB/T 4346-2008
ICS 25.060.20
J 52
Replacing GB/T 4346.1-2002
Machine tools - Manually operated self-centring chucks
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative reference documents ... 4
3 Terms and definitions ... 5
4 Types and parameters ... 6
4.1 Types ... 6
4.2 Parameters ... 7
4.3 Chuck jaws ... 9
5 Technical requirements ... 9
5.1 Appearance ... 9
5.2 Materials and heat treatment ... 10
5.3 Transmission smoothness ... 10
5.4 Clamping range ... 10
5.5 Balance ... 11
5.6 Geometric accuracy ... 11
5.7 Clamping force ... 12
5.8 Limit speed ... 12
6 Test methods ... 12
6.1 Balance ... 12
6.2 Geometric accuracy inspection ... 13
6.3 Clamping force measurement ... 14
6.4 Limit speed determination ... 14
7 Inspection rules ... 14
7.1 Factory inspection ... 14
7.2 Type inspection ... 15
8 Marking and packaging ... 15
Appendix A (Informative) Check bar and test ring diameters ... 16
This standard replaces GB/T 4346.1-2002 Self-centring manually-operated chucks for
machine tools - Part 1: Dimensions and specifications.
Compared with GB/T 4346.1-2002, the main changes in this standard are as follows:
-- The definitions of "base or master jaw" and "top jaw" are deleted (3.1 and 3.2 of
the 2002 edition);
-- All parameters of the 800 mm specification are added (see Table 1 ~ Table 8 of
this edition);
-- The specifications of 630 are adjusted: The D1 size in Table 2 is adjusted from
545 to 560, the D2 size is adjusted from 586 to 595, and the D3min size is adjusted
from 240 to 260. In Table 4, the D3min size is adjusted from 250 to 350, and the
Hmax size is adjusted from 270 to 200;
-- The static balance retains the original level II accuracy value with reference to
Japanese standards (see 5.5.1 of this edition);
-- Sizes for interchangeability of two-piece jaws (tongue and groove type) are
deleted (Figure 4 and Table 5 of the 2002 version);
-- The geometric accuracy inspection of chucks with two-piece jaws but without a
top jaw is deleted (Appendix A of the 2002 version).
Appendix A of this standard is an informative appendix.
This standard was proposed by China Machinery Industry Federation.
This standard shall be under the jurisdiction of the National Technical Committee on
Metal Cutting Machine Tool of Standardization Administration of China (SAC/TC22).
Drafting organization of this standard: Hohhot Zhonghuan (Group) Co., Ltd., Zhejiang
Yuanpai Machine Tool Accessory Co., Ltd., Machine Tool Accessory Branch of Tianjin
Zeer NC Machine Tool Component Co., Ltd., Wafangdian Yongchuan Machine Tool
Accessory Co., Ltd., Wuxi Jianhua Machine Tool Accessories Group Co., Ltd.
Main drafters of this standard: Du Shucheng, Zhang Guobin, Ye Taigen, Xu Decai, Xu
Shishun, Liu Shide, Shi Shuqing.
The previous versions of the standards replaced by this standard are as follows:
-- GB 4346-1984, GB/T 4346.1-2002.
Machine tools - Manually operated self-centring chucks
1 Scope
This standard specifies the type and parameters, technical requirements, test methods,
inspection rules, marking, and packaging of manually operated self-centring chucks
(hereinafter referred to as chucks).
This standard is applicable to scroll three-jaw chucks, and it also can be used as a
reference for other scroll chucks.
2 Normative reference documents
The provisions in the following documents become the provisions of this standard
through reference in this standard. For the dated references, the subsequent amendments
(excluding corrections) or revisions do not apply to this standard, however, parties who
reach an agreement based on this standard are encouraged to study if the latest versions
of these documents are applicable. For undated references, the latest editions of the
referenced documents apply to this standard.
GB/T 5900.1-1997 Machine tools - Spindle noses and face plates - Sizes for
interchangeability - Part 1: Type A (eqv ISO 702-1:1975)
GB/T 5900.2-1997 Machine tools - Spindle noses and face plates - Sizes for
interchangeability - Part 2: Camlock type (eqv ISO 702-2:1975)
GB/T 5900.3-1997 Machine tools - Spindle noses and face plates - Sizes for
interchangeability - Part 3: Bayonet type (eqv ISO 702-3:1975)
JB/T 3207-2005 Machine tool accessory - General specification for products
JB/T 9935-1999 Machine tool accessory - Technic document compiled
ISO 3089:2005 Machine tools - Test conditions for self-centring, manually-
operated chucks with one-piece jaws
ISO 3442-1:2005 Machine tools - Dimensions and geometric tests for self-centring
chucks with two-piece jaws - Part 1: Manually operated chucks with tongue and
groove type jaws
6.3 Clamping force measurement
Clamp the dynamometer with the internal jaws, keep the force measuring point as close
to the end face of the chuck as possible, and then clamp them in sequence with a wrench.
When the dynamometer is too large relative to the clamping diameter of the chuck, for
example, for chucks with a diameter not larger than 160 mm, special jaws are allowed
to be used.
6.4 Limit speed determination
Under the conditions where the limit speed is limited, use an instrument to test the limit
speed of the chuck. In actual measurement, the equivalent internal jaw clamping method
can also be used; according to the ratio of the center-of-mass radius of the internal jaw
clamping state to the external jaw clamping state, and based on the measured value of
the clamping force loss in the internal jaw clamping state, the actual value of clamping
force loss in the external jaw clamping state can be calculated. The speed at which this
actual value reaches two-thirds of the static clamping force is the limit speed.
F1 --The actual measured value of clamping force loss when the internal jaws
clamp the dynamometer, the unit is kilonewton (kN);
F2 -- Two-thirds of the static clamping force, the unit is kilonewton (kN);
r1 -- The radius of the center of mass of the jaws when the internal jaws clamp the
dynamometer, in millimeters (mm);
r2 -- The center-of-mass radius of the jaws when the external jaws are flush with
the outer circle of the chuck, in millimeters (mm).
7 Inspection rules
7.1 Factory inspection
Each chuck must pass the inspection before leaving the factory. The inspection items
include appearance, geometric accuracy, marks, and packaging.
7.2 Type inspection
Type inspection items include all technical requirements involved in this standard and
the corresponding test methods, marks, and packaging. Type inspection shall be carried
out under one of the following circumstances.
a) Trial prototype appraisal for new products or for the production of original
products transferred to another factory;
b) After the product is officially produced, there are major changes in process,
structure, materials, etc., which may affect product performance;
c) When production resumes after a long-term suspension;
d) When the enterprise conducts regular quality inspections or when the superior
quality supervision agency proposes type inspection requirements.
Sampling and evaluation can be carried out in accordance with relevant industry
regulations if there is no agreement between the supplier and the buyer. The sampling
quantity for static balance and clamping force determination shall generally not be less
than three.
8 Marking and packaging
8.1 The chuck shall be marked with the manufacturer's name or trademark.
8.2 A chuck wrench and bolts for installing the chuck shall be supplied with the machine;
a wrench for the jaw screws shall be provided with the two-piece jaw chuck.
8.3 Packaging shall comply with the regulations of JB/T 3207-2005.
8.4 Accompanying technical documents shall comply with the provisions of JB/T 9935-

Standard ID GB/T 4346-2008 (GB/T4346-2008)
Description (Translated English) Machine tools. Manually operated self-centring chucks
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard J52
Classification of International Standard 25.060.20
Word Count Estimation 13,123
Date of Issue 2008-06-03
Date of Implementation 2009-01-01
Older Standard (superseded by this standard) GB/T 4346.1-2002
Drafting Organization Hohhot Focus ring (Group) Co., Ltd.
Administrative Organization National Standardization Technical Committee of metal cutting machine tools
Regulation (derived from) National Standard Approval Announcement 2008 No.9 (Total No.122)
Proposing organization China Machinery Industry Federation
Issuing agency(ies) Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China; Standardization Administration of China
Summary This standard specifies the manual self-centering chuck (hereinafter referred to as chuck) the type and parameters, technical requirements, test methods, inspection rules, logo and packaging. This standard applies to plate wire type jaw chuck, chuck the other plate wire can also refer to the use.