HOME   Cart(0)   Quotation   About-Us Tax PDFs Standard-List Powered by Google www.ChineseStandard.net Database: 189759 (8 Dec 2024)

GB/T 3903.39-2019 Related PDF English (GB/T 3903.39-2008)

GB/T 3903.39-2019 (GB/T3903.39-2019, GBT 3903.39-2019, GBT3903.39-2019) & related versions
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)See DetailStatusSimilar PDF
GB/T 3903.39-2019English130 Add to Cart 0-9 seconds. Auto delivery. Footwear -- Test methods for uppers -- Delamination resistance GB/T 3903.39-2019 Valid GBT 3903.39-2019
GB/T 3903.39-2008English150 Add to Cart 0-9 seconds. Auto delivery. Footwear -- Test methods for uppers -- Delamination resistance GB/T 3903.39-2008 Obsolete GBT 3903.39-2008
Buy with any currencies (Euro, JPY, KRW...): GB/T 3903.39-2019    Preview this PDF: GB/T 3903.39-2019



GB/T 3903.39-2019 Footwear - Test methods for uppers - Delamination resistance ICS 61.060 Y78 National Standards of People's Republic of China Replace GB/T 3903.39-2008 Footwear test method (ISO 17698.2016, IDT) Published on.2019-08-30 2020-03-01 implementation State market supervision and administration China National Standardization Administration issued Foreword This part is drafted in accordance with the rules given in GB/T 1.1-2009. This part replaces GB/T 3903.39-2008 "Sheet upper test method for interlayer peel strength", and GB/T 3903.39- Compared to.2008, the main technical changes are as follows. --- Revised scope (see Chapter 1, Chapter 1 of the.2008 edition); --- Revised the canonical reference document (see Chapter 2, Chapter 2 of the.2008 edition). This section uses the translation method equivalent to ISO 17698.2016 "Shoes upper test method interlayer peel strength". The documents of our country that have a consistent correspondence with the international documents referenced in this part are as follows. ---GB/T 3903.7-2019 footwear footwear test method aging treatment (ISO 20870..2017, IDT) ---GB/T 6682-2008 Analytical laboratory water specifications and test methods (ISO 3696.1987, MOD) --- GB/T 16825.1-2008 Inspection of static single-axis testing machines - Part 1. Tensile and/or Inspection and calibration (ISO 7500-1.2004, IDT) ---GB/T 22049-2019 Standard environment for environmental conditioning and testing of footwear footwear and footwear components (ISO 18454.2018, IDT) ---GB/T 22050-2008 Sampling position, preparation and environmental adjustment time of footwear samples and samples (ISO 17709.2004, IDT) Please note that some of the contents of this document may involve patents. The issuing organization of this document is not responsible for identifying these patents. This part was proposed by the China Light Industry Federation. This part is under the jurisdiction of the National Technical Committee for the Standardization of Footwear (SAC/TC305). This section drafted by. China Leather and Footwear Industry Research Institute Wenzhou Institute, China Leather Shoes Research Institute Co., Ltd., Zhejiang Olympics Kang Shoes Industry Co., Ltd. The main drafters of this section. Chen Qixian, Yu Shuxian, Wang Zhenduo, Feng Xugen. The previous versions of the standards replaced by this section are. ---GB/T 3903.39-2008. Footwear test method 1 Scope This part of GB/T 3903 specifies the test method for the peel strength between the layers, in order to assess the suitability of the end use. This section applies to the upper surface of coated materials. 2 Normative references The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. ISO 3696 Analytical Laboratory Water Specifications and Test Methods (Waterforanalyticallaboratoryuse-Specification) Andtestmethods) ISO 7500-1 - Calibration and testing of static single-axial testing machines - Part 1 . Tension and/or pressure testing machines Calibration and verification of force measurement systems (Metalicmaterials-Calibrationandverificationofstaticuniaxialtestingma- chines-Part 1.Tension/compressiontestingmachines-Calibrationandverificationoftheforce-meas- Ouringsystem) ISO 17709 Sampling position, preparation and environmental conditioning time for footwear samples and specimens (Footwear-Samplinglocation, Preparationanddurationofconditioningofsamplesandtestpieces) ISO 18454 Standard environment for environmental conditioning and testing of footwear footwear and footwear components (Footwear-Standardatmospheres Forconditioningandtestingoffootwearandcomponentsforfootwear) ISO 20870 Footwear-Ageingification 3 Terms and definitions The following terms and definitions apply to this document. 3.1 Interlaminar peel strength delaminationresistance The bond strength between the coating and the base material. 4 Test equipment and materials The following equipment and materials should be used. 4.1 Tensile testing machine, the moving speed of the clamp is (100±10)mm/min, and the applicable force range of the sample (for polyurethane coating) Fabric sample) is usually 0N~200N, the accuracy of measuring force should meet the requirements of level 2 in ISO 7500-1, and the force measurement accuracy is large. At 2%. 4.2 Automatic recorder, or similar equipment, can continuously record force values. 4.3 Rapid plate press, capable of applying (550 ± 50) kPa pressure in an area of 50 mm × 70 mm. 4.4 Rubber sheet with a thickness of at least 10 mm and a hardness of (40 ± 10) IRHD. 4.5 Radiant heater, power 3kW, heating area is about 0.06m2, can heat the dry film on the resin rubber to 80 °C within 15s~ 90 ° C. The film is usually placed approximately 100mm~150mm from the heater. It is advisable to use the outsole used in the production of shoes and Activating device for the face. 4.6 Thermal pen or temperature gun, check the temperature of the film at 80 ° C ~ 90 ° C equipment. It is advisable to use a thermal pen or red with a melting temperature of 83 °C. External temperature gun. 4.7 Resin rubber, thickness (3.5 ± 0.2) mm, hardness (95 ± 2) IRHD, surface peel strength is greater than the sample to be tested. Note. IRHD is the international rubber hardness, hardness (95 ± 2) IRHD equivalent to (95 ± 2) Shore A. 4.8 Solvent-based polyurethane adhesive with good adhesion to resin rubber and sample coating. 4.9 Adhesive treatments, such as halogenating agents, can effectively increase the adhesion of rubber in the production of footwear. 4.10 Cutting equipment, such as punching or scissors, can cut rectangular specimens of size (50 ± 1) mm × (70 ± 1) mm. In addition, if yes Hydrolyzed samples were tested and another shear tool was required to cut a square specimen with a side length of (70 ± 1) mm. 4.11 Shearing tools, such as sharp knives or disc knives, can be sampled from bonded specimens. This device should not be excessively compressed or will be sampled The edge of the sample is layered, so it is not advisable to use a punching knife. 4.12 Distilled or deionized water. If wet bond strength is measured, use tertiary or deionized water in accordance with ISO 3696. 4.13 Timer, range 30s, accurate to 0.5s. 5 sampling 5.1 For dry tests, mark six rectangles (70 ± 1) mm × (50 ± 1) mm on the back of the sheet or upper. two long sides and sheets Parallel to the direction (machine direction or ridge line direction) or in the X-axis direction of the sill (as defined in ISO 17709), the other four long sides and the above The direction is vertical. 5.2 For the wet test, mark two rectangles (70 ± 1) mm × (50 ± 1) mm on the back of the material or upper, and place the 50 mm edge. Consistent with the direction of the lowest peel strength (if known) in the dry test, or prepare six more rectangles as shown in 5.1. 5.3 Further marking on the material, divide the rectangular material marked in 5.1 and 5.2 into two pieces, (35 ± 0.5) mm × (50 ± 1) mm. Mark the machine direction or X-axis direction on each small rectangular specimen. Use the arrows to mark the direction and make sure the arrows point in the same direction. Correct For the upper face, the arrow should point to the toe. 5.4 For the damp heat aging test, two squares are required to be marked with a side length of (70 ± 1) mm and sides parallel to the X axis. Marking machine by 5.3 Arrow in the direction of the device or in the direction of the X axis. Note. It is recommended to use the chamfer method for marking because the wet or damp heat aging treatment can make the mark imprint fade. 5.5 Take the rectangle marked in 5.1 and 5.2 and the square marked in 5.4 from the sheet or the upper surface, and then cut each material into two (30 ± 0.5) mm × (50 ± 1) mm sample, see Figure 1. After bonding with the resin rubber, each piece of material is subsequently cut into two layers From the sample. Some types of shoes may not be cut to the specified size, in which case a sample should be taken from the sample and the size can be Reduce to (40 ± 1) mm × (50 ± 1) mm, and no further cutting according to the requirements of 5.3. 5.6 Cut (50 ± 1) mm × (70 ± 1) mm rectangular resin rubber on each piece of resin on the resin rubber according to the relevant dimensions in 5.5. (4.7). If the radiant heater (4.5) needs to be calibrated before use, an additional one or two pieces of resin rubber should be cut. The unit is mm Description. 1---cut direction; 2---about 5mm; 3---stitch; 4---cut line; 5---bar paper. Note. Samples can be taken from the upper material, the forming surface or the finished shoe. Figure 1 sample assembly drawing 6 Test methods 6.1 Test principle The coating of the sample is bonded to the resin rubber block with a strong adhesive. In the state where the finishing layer is still bonded to the rubber, the tensile test is used. The force required to peel the sample from the resin rubber was measured. Wet samples and hydrolyzed samples can also be tested. 6.2 Test procedure 6.2.1 Place a strip of paper (75 ± 5) mm × (15 ± 3) mm on the finish of each side of the material cut in 5.5. will The strips are stapled (or similar) to secure the two ends. The position of the staples is shown in Figure 1. From the four specimens of the dry test (marked arrow Take two specimens to its long side. The direction of the paper is placed in the same direction as the arrow. On the other two specimens, the paper is placed along the opposite side. 6.2.2 If a treatment agent (4.9) can be used, it should be applied to the resin rubber cut from 5.6 according to the supplier's instructions. The entire back. 6.2.3 Allow the resin rubber to dry completely according to the requirements of use. 6.2.4 Apply a polyurethane adhesive (4.8) to the entire back of each resin rubber according to the supplier's instructions. 6.2.5 Similarly, apply a bond to the coated side of each piece of material to be tested so that it overlaps the strip of paper. 6.2.6 The adhesive is dried for at least 1 h. 6.2.7 If the time required to heat the adhesive layer to 80 ° C ~ 90 ° C using a radiant heater is unknown, use the two additional cuts in 5.6 The time required for the rubber measurement and the temperature of the adhesive layer (4.6) were detected. If the time is greater than 15s, increase the temperature of the radiant heater or reduce it. The distance between the heater and the resin rubber until the time is less than 15 s. Recording the time required to heat the adhesive layer to the specified temperature Ta, Accurate to 1s. 6.2.8 Preparation of bonded assembly specimens. 6.2.8.1 Place an adhesive-coated resin rubber in a radiant heater with the bonding surface facing the heating source and heating to Ta (in seconds). 6.2.8.2 Carefully and quickly contact the bonding surface of the bonding material with the bonding surface of the resin rubber to align the edges of the two surfaces. Following It is called an assembly sample). 6.2.8.3 Immediately place the assembled specimen onto the fast plate press (4.3) with the resin rubber side facing the rubber sheet (4.4). Assembly The sample was applied with a pressure of (550 ± 50) kPa for a time of (15 ± 1) s. The key point of operation is to remove the resin rubber from the heater of 6.2.8.1 to place the sample between the plate presses in 6.2.8.3. The time should not exceed 7s. 6.2.9 Assembly specimens are placed in a standard environment as specified in ISO 18454 for a period of at least 24 h. 6.2.10 Use the shearing tool (4.11) to make 3 cuts in parallel with the 50mm side on the assembled specimen to form the middle part of the specimen. Two strips of width (30.0 ± 0.5) mm, length (50 ± 1) mm, and two strips of outer width of about 5 mm, see Figure 1. 6.2.11 Open the unbonded area of each sample, taking care not to break the bond line and clamp it symmetrically to the tensile tester (4.1) The unbonded resin rubber and the facing material are respectively clamped in the two clamps of the tensile machine (see Fig. 2). Description. 1---stripe peel strength in Newtons (N); 2---average force value; 3---displacement. Figure 2 Force-displacement diagram 6.2.12 Start the tensile testing machine, the separation speed of the clamp is (100 ± 10) mm/min, record separation type, such as. a) adhesion failure of the base fabric layer; b) damage to the base fabric layer; c) deep damage of the base fabric; d) adhesion failure between the microporous solidified layer and the outer surface coating; e) damage between micropores or solidified layers; f) Separation between the microporous or solidified layer and the base fabric. If the separation occurs between the surface coating and the resin rubber, stop the test immediately (but do not need to remove the sample from the tensile machine), with the front The sharp knife is carefully cut along the point of separation close to the coating surface so that separation occurs between the coating and the substrate material. 6.2.13 Determine the force and displacement curves on the tensile test machine. 6.2.13.1 Initial maximum force value of coating damage in Newtons. 6.2.13.2 The average force value required to separate the coating from the substrate (the average of all force values after the initial maximum force value) (see Figure 2), The unit is Newton. 6.2.14 Repeat the test procedure of 6.21.1~6.2.13 for other dry samples. 6.2.15 For wet samples. 6.2.15.1 Select the sample with the minimum peel strength in the dry test calculated according to 7.1.1 and immerse it in water with a water temperature of (23 ± 2) °C (see In 4.12), the time is (6.0 ± 0.5) h. 6.2.15.2 Remove each sample from the water, gently wipe off the excess water on the surface, and immediately perform the test procedures of 6.21.1 to 6.2.33. 6.2.16 If the wet heat aging sample is tested. 6.2.16.1 Two specimens were prepared according to ISO 20870 wet heat aged materials. 6.2.16.2 Cut 1 rectangular specimen (70±1) mm×(50±1)mm from each wet heat aging material, and the length and length of 50mm The direction of the lowest peel strength in the dry test calculated in 7.1.2 is consistent. 6.2.16.3 Repeat the test procedure of 6.2.1~6.2.13 for the other two damp heat aging samples. 7 test results 7.1 For each sample, calculate. 7.1.1 The initial maximum peel force value measured in 6.2.13.1 is divided by the width of the sample to obtain the initial maximum peel strength in The cow is accurate to 0.1 N/mm per millimeter (N/mm). 7.1.2 The average force value measured in 6.2.13.2 is divided by the width of the sample to obtain the average peel strength in units of cattle per millimeter (N/mm), accurate To 0.1 N/mm. 7.2 For each stripping direction, calculate. 7.2.1 The arithmetic mean of the initial maximum peel strength calculated in 7.1.1. 7.2.2 The arithmetic mean of the average peel strength calculated in 7.1.2. 8 test report The test report should include the following. a) Type of sample. ---Pretreatment, wetting or damp heat aging; --- peeling direction; --- The arithmetic mean of the initial maximum peel strength is performed in accordance with 7.2.1; --- The arithmetic mean of the average peel strength is performed in accordance with 7.2.2; b) if the shoe or upper is tested, describe the style of the shoe, including the item number; c) description of the material, including known business information, if possible; d) the number of this part; e) the date of the test; f) Any deviation from this test method. ......


GB/T 3903.39-2008 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 61.060 Y 78 GB/T 3903.39-2008 / ISO 17698.2003 Footwear - Test methods for uppers - Delamination resistance (ISO 17698.2003, IDT) ISSUED ON. DECEMBER 30, 2008 IMPLEMENTED ON. SEPTEMBER 1, 2009 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration Committee. Table of Contents Foreword ... 3  1 Scope ... 4  2 Normative references ... 4  3 Terms and definitions ... 5  4 Apparatus and material ... 5  5 Sampling ... 6  6 Test method ... 7  7 Expression of results ... 11  8 Test report ... 11  Foreword This Part of GB/T 3903 identically adopts the International Standard ISO 17698.2003 Footwear - Test methods for uppers - Delamination resistance (English version). For easy use, this Part makes the following editorial modifications. a) modified “this International Standard” to “this Part”; b) used decimal point “.” to replace “,” which was used as decimal point; c) deleted the foreword of ISO 17698.2003; d) deleted the table of contents of ISO 17698.2003; e) directly used a national standard as reference which is corresponding to the International standard that was used as reference in ISO 17698.2003; f) deleted the appendix of ISO 17698.2003. This Part was proposed by China Light Industry Association. This Part shall be under the jurisdiction of National Technical Committee on Footwear of Standardization Administration of China. The drafting organizations of this Part. China Institute of Leather and Footwear Industry, Fujian Footwear Industry Technology Development (Putian) Base. Main drafters of this Part. Yan Huaidao, Zhang Weijuan, Wang Dechun. Footwear - Test methods for uppers - Delamination resistance 1 Scope This Part of GB/T 3903 specifies a test method for determining the delamination resistance of uppers irrespective of the material, in order to assess the suitability for the end use. This Part is applicable to uppers irrespective of the material. 2 Normative references The following standards contain the provisions which, through reference in this Part of GB/T 3903, constitute the provisions of this Part. For dated references, subsequent amendments (excluding corrections) or revisions do not apply to this Part. However, the parties who enter into agreement based on this Part are encouraged to investigate whether the latest versions of these documents are applicable. For undated reference documents, the latest versions apply to this Part. GB/T 3903.7 Footwear - Ageing conditioning (GB/T 3903.7-2005, ISO 20870.2001, IDT) GB/T 6682 Water for analytical laboratory use - Specification and test methods (GB/T 6682-2008, ISO 3696.1987, MOD) GB/T 16825.1-2008 Verification of static uniaxial testing machines - Part 1. Tension/compression testing machines - Verification and calibration of the force-measuring system (ISO 7500-1.2004, IDT) GB/T 22049 Footwear - Standard atmospheres for conditioning and testing of footwear and components for footwear (GB/T 22049-2008, ISO 18454.2001, IDT); GB/T 22050 Footwear - Sampling location preparation and duration of conditioning of samples and test pieces (GB/T 22050-2008, ISO 17709.2004, IDT) ......

BASIC DATA
Standard ID GB/T 3903.39-2019 (GB/T3903.39-2019)
Description (Translated English) Footwear -- Test methods for uppers -- Delamination resistance
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard Y78
Classification of International Standard 61.060
Word Count Estimation 10,128
Date of Issue 2019-08-30
Date of Implementation 2020-03-01
Drafting Organization China Leather and Footwear Industry Research Institute Wenzhou Research Institute, China Leather and Footwear Research Institute Co., Ltd., Zhejiang Aokang Footwear Co., Ltd.
Administrative Organization National Standardization Technical Committee for Footwear (SAC/TC 305)
Proposing organization China National Light Industry Federation
Issuing agency(ies) State Administration for Market Regulation, China National Standardization Administration

BASIC DATA
Standard ID GB/T 3903.39-2008 (GB/T3903.39-2008)
Description (Translated English) Footwear. Test methods for uppers. Delamination resistance
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard Y78
Classification of International Standard 61.060
Word Count Estimation 8,825
Date of Issue 2008-12-30
Date of Implementation 2009-09-01
Quoted Standard GB/T 3903.7; GB/T 6682; GB/T 16825.1-2008; GB/T 22049; GB/T 22050
Adopted Standard ISO 17698-2003, IDT
Drafting Organization China Leather and Footwear Industry Research Institute
Administrative Organization National Standardization Technical Committee footwear
Regulation (derived from) National Standard Approval Announcement 2008 No.24 (Total No.137)
Proposing organization China Light Industry Federation
Issuing agency(ies) Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China; Standardization Administration of China
Summary This standard specifies the test methods to help face peel strength. The purpose is to assess the suitability of the final product. This section applies to a variety of footwear with uppers.