GB/T 37866-2019 (GB/T37866-2019, GBT 37866-2019, GBT37866-2019) & related versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | See Detail | Status | Similar PDF |
| GB/T 37866-2019 | English | 150 |
Add to Cart
|
0-9 seconds. Auto delivery.
|
Green product assessment -- Plastic products
|
GB/T 37866-2019
| Valid |
GBT 37866-2019
|
Buy with any currencies (Euro, JPY, KRW...): GB/T 37866-2019 Preview this PDF: GB/T 37866-2019
GB/T 37866-2019
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 13.020.20
Z 04
Green Product Assessment - Plastic Products
ISSUED ON: AUGUST 30, 2019
IMPLEMENTED ON: MARCH 1, 2020
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative References ... 4
3 Terms and Definitions ... 5
4 Requirements of Product Assessment ... 5
5 Assessment Methods ... 8
Appendix A (normative) Volatile Organic Compounds (VOC) Content
Determination Method ... 9
Green Product Assessment - Plastic Products
1 Scope
This Standard stipulates the requirements and methods for green product assessment
of plastic products.
This Standard is applicable to all the plastic products.
2 Normative References
The following documents are indispensable to the application of this document. In
terms of references with a specified date, only versions with a specified date are
applicable to this document. In terms of references without a specified date, the latest
version (including all the modifications) is applicable to this document.
GB/T 2408 Plastics - Determination of Burning Characteristics - Horizontal and Vertical
Test;
GB 4806.7 National Food Safety Standard - Food Contact Plastic Materials and
Articles;
GB/T 7119 Evaluating Guide for Water Saving Enterprises;
GB 8978 Integrated Wastewater Discharge Standard;
GB/T 9345.5 Plastics - Determination of Ash - Part 5: Poly (vinyl chloride);
GB/T 16288 Marking of Plastics Products;
GB 16297 Comprehensive Emission Standard of Air Pollutants;
GB/T 17592 Textiles - Determination of the Banned Azo Colorants;
GB/T 19001 Quality Management Systems - Requirements;
GB/T 19277.1 Determination of the Ultimate Aerobic Biodegradability of Plastic
Materials under Controlled Compositing Conditions - Method by Analysis of Evolved
Carbon Dioxide - Part 1: General Method;
GB/T 22048 Determination of Certain Phthalate Esters in Toys and Children’s Products;
GB/T 23331 Energy Management Systems - Requirements;
GB/T 24001 Environmental Management Systems - Requirements with Guidance for
Use;
GB/T 28001 Occupational Health and Safety Management Systems - Requirements;
GB/T 28206 Specification for Compostable Plastic;
GB/T 33284 Indoor Decorating and Refurbishing Materials - Limit of Harmful
Substances of Un-plasticized Polyvinyl Chloride (PVC-U) Profiles for the Doors and
Windows;
HJ/T 400-2007 Determination of Volatile Organic Compounds and Carbonyl
Compounds in Cabin of Vehicles;
QB/T 5158 Test Method of Artificial Leather and Synthetic Leather - Test of
Quantitatively Determine Dimethylformamide
3 Terms and Definitions
The following terms and definitions are applicable to this document.
3.1 Green Plastic Product
Green plastic product refers to plastic product which has no harm or little harm to the
ecological environment and human health, and has less energy consumption and a
high quality, and can comply with the requirements of environmental protection in the
full life cycle.
4 Requirements of Product Assessment
4.1 Basic Requirements
Green requirements that production enterprises shall satisfy include, but shall not be
limited to:
---Production enterprises’ pollutant discharge condition: production enterprises
shall be requested to comply with relevant laws and regulations on
environmental protection; reach the requirements of national or local pollutant
discharge standards (GB 8978 and GB 16297). There shall be no major safety
accidents and major environmental pollutant incidents in the past three years;
---Production enterprises’ total pollutant control: production enterprises shall be
requested to reach the national and local total pollutant discharge control
indicators;
---Production enterprises’ management: production enterprises shall be requested
to respectively establish and operate environmental management system,
analysis equipment may also adopt other equipment other than what is stipulated in
HJ/T 400-2007. However, it shall be guaranteed that quantitative relative standard
deviation (RSD) within the dynamic range is not more than 10%, and the quantitative
repeatability relative standard deviation (RSD) in 5 successive sample injection is not
more than 10%.
A.3 Sample
Sample dimension shall be: 100 mm 100 mm 2 mm.
A.4 Handling of Sample Bag
Firstly, seal up the sample bag, then, pump out air in the sample bag. Then, fill in the
sample bag with pure nitrogen (purity: above 99.99%), which occupies around 50% of
its volume. In 60 °C incubator, place it for 2 h. Then, use a vacuum pump to promptly
pump out air in the sample bag.
A.5 Sealing and Packaging of Sample
Sealing and packaging of sample shall comply with the following steps:
a) Measure and record the dimensions of sample (mm);
b) Inject sample into the sample bag, which is already processed in accordance
with the requirements in A.4, then, seal it up;
c) Fill in the sample bag with pure nitrogen, which occupies around 30% of the
volume of the sample bag, then, use a pump to pump out the air;
d) In accordance with c), conduct repeated operation twice, then, at 25 °C, fill in
pure nitrogen, which is around 50% of the volume of the sample bag.
A.6 Gas Trapping
Before conducting gas trapping, place the sample, which is sealed and packed in A.5,
into 60 °C incubator for 2 h. Maintain the sample at 60 °C for 2 h, then, in accordance
with the tubing demonstrated in Figure A.1 and the following steps, conduct the
sampling:
a) Lightly rub the sample bag, which is loaded with components, so that the gas
inside the bag can be homogenized. Slightly open the valve to squeeze out
residual gas in the tube;
b) On Conduit 1, install TENAX tube; on Conduit 2, install DNPH tube;
c) Open the valve on Conduit 1 and Conduit 2, then, start the sampling;
d) After the sampling of TENAX tube on Conduit 1 is completed, close the valve
If the analysis cannot be conducted immediately, use aluminum foil to properly pack
the trapping tube, then, store it in a cool and dark place (below 10 °C); the storage
period shall be 7 d at the maximum.
Under the above-mentioned conditions, use DNPH trapping tube to conduct the
sampling once. If the analysis cannot be conducted immediately, use aluminum foil to
properly pack the trapping tube, then, store it in a cool and dark place (below 10 °C);
the storage period shall be 7 d at the maximum.
A.7 Analysis
A.7.1 Analysis of benzene series
Conduct the measurement in accordance with the stipulations in 5.1 in HJ/T 400-2007,
namely, thermal desorption/capillary gas chromatography/mass spectrometry. Prepare
2 TENAX for measurement, one of which shall be reserved for later usage. When the
first TENAX is adopted in the measurement of benzene series, if quantitative
substance exceeds the linear range, highest point of standard solution may be added,
or, sampling amount may be reduced, or, the split ratio may be altered for a re-
measurement. Conduct parallel sampling (not less than 2 parallel samples), the
relative deviation between the measured value and the average value shall not exceed
20%.
A.7.2 Analysis of aldehyde ketone
Conduct the measurement in accordance with the stipulations in 5.2 in HJ/T 400-2007,
namely, solid phase adsorption/high performance liquid chromatography. In the
analysis of each batch of samples, at least retain 2 sampling tubes (1 TENAX and 1
DNPH) to conduct gas trapping and analysis of an empty bag (does not seal or pack
sample; but contains nitrogen and goes through heating treatment). This shall be
considered as on-site blank test during the sampling process. Compare the zero
concentration value of the analysis result and the calibration curve. If this turns out to
be abnormal, then, this batch of samples shall become invalid.
A.8 Data Processing and Test Report
A.8.1 Data processing
Volatile concentration shall be calculated in accordance with Formula (A.1):
Where,
C---sample volatile amount, expressed in (μg/m3);
W---compound amount measured through trapping tube, expressed in (μg);
......
| Standard ID | GB/T 37866-2019 (GB/T37866-2019) | | Description (Translated English) | Green product assessment -- Plastic products | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | Z04 | | Classification of International Standard | 13.020.20 | | Word Count Estimation | 10,175 | | Date of Issue | 2019-08-30 | | Date of Implementation | 2020-03-01 | | Drafting Organization | Beijing Technology and Business University, China National Institute of Standardization, Light Industry Plastics Processing and Application Research Institute, Zhonglan Chenguang Chemical Research and Design Institute Co., Ltd., Zhonghuan United (Beijing) Certification Center Co., Ltd., China Plastics Processing Industry Association Profile and Door and Window Products Professional Committee, Nantong Huasheng High Polymer Technology Co., Ltd., Beijing Yonghua Qingtian Design and Packaging Co., Ltd., Zhejiang Shengnuomeng Gujia Sponge Co., Ltd., Jiangsu Chemical Research Institute Co., Ltd., Zhejiang Zhongcai Profile Co., Ltd., Kingfa Technology Co., Ltd., Anhui Xiongfeng Industrial Co., Ltd., Ningbo Jialian Technology Co., Ltd., Beijing Shuangjian Plastic Packaging Products Co., Ltd. | | Administrative Organization | National Standardization Technical Committee of Bio-based Materials and Degradable Products (SAC/TC 380) | | Issuing agency(ies) | State Administration for Market Regulation, China National Standardization Administration |
|