GB/T 2899-2017 (GB/T2899-2017, GBT 2899-2017, GBT2899-2017) & related versions
Buy with any currencies (Euro, JPY, KRW...): GB/T 2899-2017 Preview this PDF: GB/T 2899-2017
GB/T 2899-2017
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 71.060.50
G 12
Replacing GB/T 2899-2008
Barium sulphate precipitated for industrial use
工业沉淀硫酸钡
ISSUED ON: NOVEMBER 01, 2017
IMPLEMENTED ON: MAY 01, 2018
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Molecular formula and relative molecular mass ... 5
4 Requirements ... 5
5 Test method ... 6
6 Inspection rules ... 15
7 Markings and labels ... 16
8 Packaging, transportation and storage ... 16
Barium sulphate precipitated for industrial use
1 Scope
This standard specifies the requirements, test methods, inspection rules,
markings, labels, packaging, transportation and storage of barium sulphate
precipitated for industrial use.
This standard applies to barium sulphate precipitated for industrial use. This
product is mainly used in coatings, inks, pigments, rubber, batteries, plastics
and coated paper, metal smelting and other industries.
2 Normative references
The following documents are essential to the application of this document. For
the dated documents, only the versions with the dates indicated are applicable
to this document; for the undated documents, only the latest version (including
all the amendments) are applicable to this standard.
GB/T 191-2008 Packaging - Pictorial marking for handling of goods
GB/T 1717-1986 Determination of pH value of an aqueous suspension of
pigments
GB/T 3049-2006 Chemical products for industrial use. General method for
determination of iron content - 1, 10-Phenanthroline spectrophotometric
method
GB/T 5211.2 Determination of matter soluble in water of pigments-Hot
extraction method
GB/T 5211.3 Determination of matter volatile of pigments at 105 °C
GB/T 5211.15-2014 General test methods for pigments and extender
pigments - Part 15: Determination of oil absorption
GB/T 5950-2008 Method for measurement of whiteness of building materials
and non-metal mineral products
GB/T 6003.1-2012 Test sieves - Technical requirements and testing - Part 1:
Test sieves of metal wire cloth
GB/T 6678 General principles for sampling chemical products
5.3.2.8 Methyl orange indicator solution: 1 g/L.
5.3.3 Instrument and equipment
5.3.3.1 Platinum crucible with lid.
5.3.3.2 High temperature electric furnace: The temperature can be controlled
at 800 °C ± 20 °C and 600 °C ± 20 °C.
5.3.4 Test procedure
Weigh about 1 g of the specimen which had been dried according to 5.4,
accurate to 0.0002 g. Place it in a platinum crucible into which 4 g of molten
mixture has been added. Mix it uniformly. Then cover another 4 g of molten
mixture above it and close the lid. Place the platinum crucible in a high-
temperature electric furnace. Melt it at 800 °C ± 20 °C for 40 min. Take it out to
cool it down.
In a 250 mL beaker, use 100 mL ~ 150 mL of hot water to leach out the melt.
Use a glass rod with a rubber tip to transfer all the white melt to the beaker.
Heat to boil it, until the melt is loose. Let it stand for a while. Use the slow
quantitative filter paper to filter the supernatant first. Then use the hot
anhydrous sodium carbonate solution to wash the insoluble matter by
decantation. Transfer the insoluble matter to the filter paper to continue washing
until it is free of sulfate (testing method: Take 2 mL of filtrate; add 2 drops of
hydrochloric acid solution and 0.5 mL of barium chloride solution; the solution
shall remain transparent after 10 min). Discard the filtrate.
Add 30 mL of hot hydrochloric acid solution to the funnel, in six times, to dissolve
the precipitate. After adding the hydrochloric acid solution, quickly place the
watch glass on the funnel. Collect the filtrate in a 500 mL beaker. After adding
the hydrochloric acid solution each time, use hot water to wash it once. After
the hydrochloric acid solution is completely added, use hot water to rinse the
watch glass and the filter paper on the funnel, until it is free of chloride (Testing
method: Take 2 mL of filtrate; add 0.5 mL of silver nitrate solution; it shall remain
transparent after 5 min). Add 2 ~ 3 drops of methyl orange indicator solution in
the filtrate, use ammonia solution to neutralize until it becomes pale yellow. Add
2 mL of hydrochloric acid solution. Finally add water to adjust the solution
volume to 400 mL.
Heat the solution to boiling. Add 20 mL of hot sulfuric acid solution at a uniform
rate under stirring. Control the addition within 2 min ~ 2.5 min. Cover the watch
glass. Place the beaker on the boiling water bath for 2 h or room temperature
for more than 12 h. Use slow quantitative filter paper to filter it. Use hot water
to rinse the precipitate until the filtrate is free of chloride (the testing method is
the same as before). Place the precipitate and filter paper in a porcelain crucible
that was burned to constant temperature at 600 °C ± 20 °C in advance. Dry and
5.7 Determination of whiteness
5.7.1 Instrument and equipment
5.7.1.1 Whiteness meter: Same as Chapter 5 of GB/T 5950-2008.
5.7.1.2 Standard whiteboard: Same as Chapter 6 of GB/T 5950-2008.
5.7.2 Test procedure
Same as Chapter 7 and Chapter 8 of GB/T 5950-2008.
5.7.3 Processing of test data
As specified in Chapter 9 of GB/T 5950-2008, it is calculated using the blue light
whiteness formula.
Take the arithmetic mean of the parallel determination results as the
measurement result. The absolute difference between the parallel
determination results is not more than 1.0.
5.8 Determination of oil absorption
5.8.1 Reagents or materials
Same as Chapter 4 of GB/T 5211.15-2014.
5.8.2 Instrument and equipment
Same as Chapter 5 of GB/T 5211.15-2014.
5.8.3 Test procedure
Weigh about 10 g of specimen, accurate to 0.01 g. Put it on a flat plate. From a
drip bottle which contains refined linseed oil of known mass (accurate to 0.01
g), add refined linseed oil dropwise, 4 ~ 5 drops a time. After each addition, use
a knife to continually press-grind it forcedly. When approaching to the end point,
it shall add it dropwise. After finishing the last drop, the specimen is wetted by
the oil and forms a whole block. When it is not cracked or broken when
spreading, and can adhere to the flat plate, it is used as the end point. All
operations shall be completed within 20 min ~ 25 min. Finally weigh the mass
of the drip bottle.
5.8.4 Processing of test data
The oil absorption is calculated by w3. The value is expressed by the mass of
oil absorbed per 100 g of sample, calculated according to formula (3):
5.11.2.2 Iodine solution: c (1 / 2I2) ≈0.01 mol/L. Pipette 10 mL of the iodine
standard titration solution prepared according to 5.9.1 in HG/T 3696.1-2011.
Place it in a 100 mL brown volumetric flask. Use water to dilute it to the mark.
Shake it uniformly.
5.11.2.3 Starch indicator solution: 5 g/L. Weigh 0.5 g of starch. Add 5 mL of
water to make it into a paste. Add the paste to 90 mL of boiling water whilst
stirring it. Boil it for 1 min ~ 2 min. Cool it down. Dilute it to 100 mL. The period
of use is two weeks.
5.11.2.4 Sodium thiosulfate standard titration solution: c (Na2S2O3) ≈0.01
mol/L. Pipette 25 mL of sodium thiosulfate standard titration solution prepared
and calibrated according to 5.6 of HG/T 3696.1-2011 in a 250 mL volumetric
flask. Use water to dilute it to the mark. Shake it uniformly.
5.11.3 Test procedure
Weigh about 10 g of specimen, accurate to 0.01 g. Place it in a 250 mL (V2)
volumetric flask. Add 100 mL of water. Add the stopper. Shake it vigorously for
2 min. Use water to dilute it to the mark. Shake it uniformly. Filter it. Discard the
initial 20 mL of filtrate. If the filtrate is cloudy, it shall be returned to re-filter it,
until the filtrate is clear. Pipette 100 mL (V1) of filtrate into a 250 mL iodine flask.
Use a pipette to add 5 mL of iodine solution and 5 mL of acetic acid solution.
Use water to seal it. Shake it uniformly. Place it in a dark place for 5 min. Use
the sodium thiosulfate standard titration solution to titrate it. When approaching
to the end point, add 2 mL of starch solution. Continuously use sodium
thiosulfate standard titration solution to titrate it, until the blue color disappears,
which is used as the end point.
Do a blank test at the same time. Except that no sample is added, the types
and amounts of other reagents added (except standard titration solution) are
exactly the same as the test solution; meanwhile it is treated in the same way
as the sample.
5.11.4 Processing of test data
The content of sulfide is calculated by the mass fraction w5 of sulfur (S),
according to formula (5):
Where:
V0 - The value of the volume of sodium thiosulfate standard titration solution
consumed in the titration of the blank test solution, in milliliters (mL);
6 Inspection rules
6.1 This standard uses type inspection and exit-factory inspection. Type
inspection and exit-factory inspection shall meet the following requirements:
a) All the index items specified in the requirements are type inspection items.
Under normal production conditions, the type inspection shall be
conducted at least once every three months. In one of the following
situations, type inspection shall be carried out:
- Update of key production process;
- Change of main raw materials;
- Production restoration after suspension;
- Big difference from the last type inspection;
- Contract provisions.
b) The eight indicators of barium sulfate content, volatile content at 105 °C,
water soluble content, iron content, whiteness, oil absorption, pH, fineness
as specified in the requirements are exit-factory inspection items and shall
be inspected batch by batch.
6.2 The barium sulphate precipitated for industrial use of the same grade as
produced continuously (or by the same shift) by the manufacturer using the
same materials, basically the same production conditions form a batch. Each
batch of products does not exceed 120 t.
6.3 Determine the number of sampling units according to the provisions of GB/T
6678. When sampling, the sampler is inserted vertically from the center of the
packaging bag to sample at 3/4 of the depth of the material layer. Mix the
sampled products. Use the quartile method to reduce to not less than 1000 g.
Put the sample into two clean and dry containers. Seal it. Paste the label,
indicating the manufacturer name, product name, grade, batch number,
sampling date, sampler's name. One is used for inspection and the other is
retained for future reference. The retention time is determined by the
manufacturer according to the actual situation.
6.4 If an index of inspection results does not meet the requirements of this
standard, it shall take sample from twice the amount of packaging for re-
inspection. If an index of the re-inspection does not meet the requirements of
this standard, the entire batch of products is unqualified.
6.5 Use the rounding value comparison method as specified in GB/T 8170 to
determine whether the inspection result meets the standard.
......
GB/T 2899-2008
Barium sulphate precipitated for industrial use
ICS 71.060.50
G12
National Standards of People's Republic of China
Replacing GB/T 2899-1996
Industrial precipitated barium sulfate
(ISO 3262-3.1998 Extendersforpaints-Specificationsandmethodsoftest-
Part 3. Blancfixe, MOD)
Posted 2008-04-10
2008-10-01 implementation
Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China
Standardization Administration of China released
Foreword
Please note that some of the content of this standard may involve patents. The standard release mechanism should not bear the responsibility to identify these patents.
This revised standard adopts ISO 3262-3.1998 "paints - Part 3 packing specifications and test methods. barium sulfate powder" (English
Version).
Taking into account China's national conditions, the use of international standards ISO 3262-3.1998, the standard of this made some changes. About the technical difference is
Incorporated into the text and a single vertical line identifies them involved with the provisions margin. These are given in Appendix A and Appendix B
List of technical differences, structural differences and the reasons for the reference.
This standard replaces GB/T 2899-1996 "industrial precipitated barium sulfate."
This standard and GB/T 2899-1996 main technical differences are as follows.
--- Canceled class Ⅱ paste Indicators (1996 version 4.2, this version 4.2);
--- The oil absorption index range was adjusted to (10 ~ 30) g/100g (1996 version 4.2, this version 4.2);
--- Laser particle size distribution measurement instead particle size analyzer (1996 version 6.12, this version 5.12);
--- The standard test classified into type inspection and factory inspection (edition 6.1).
The Standard Appendix A and Appendix B is an informative annex.
The standard proposed by China Petroleum and Chemical Industry Association.
This standard by the National Standardization Technical Committee chemical inorganic chemicals Club (SAC/TC63/SC1) centralized.
This standard drafting units. Tianjin Chemical Research & Design Institute of Chemical Industry Group Co., Ltd. barium southerly branch of industry, Zhuzhou days Longhua
Workers Industrial Co., Ltd., Hebei Xinji Chemical Group Co., Ltd., Shaanxi Fuhua Chemical Co., Ltd.
The main drafters of this standard. Li Xia, Su Di, Hu Zhiyong, Wang Fanfan, Bai Junsheng, Zhang Jingjuan.
This standard replaces the standards previously issued as follows.
--- GB/T 2899-1982, GB/T 2899-1996.
Industrial precipitated barium sulfate
1 Scope
This standard specifies the requirements of industrial precipitated barium sulfate, test methods, inspection rules, marking, labeling, packaging, transportation and storage.
This standard applies to industrial precipitated barium sulfate. The products are mainly used in coatings, inks, paints, rubber, batteries, and plastic coated paper, etc.
industry.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 191-2000 Packaging - Pictorial signs (eqv ISO 780.1997)
Representation GB/T 1250 limit values \u200b\u200band the method of determining
GB/T 1717-1986 Determination of aqueous pigment suspension pH value (eqv ISO 787-9. 1981)
General Method GB/T 3049-2006 industrial chemicals determination of iron content 1,10 Philippines spectrophotometry method
(ISO 6685. 1982, IDT)
GB/T 5211.2-2003 aqueous pigment composition Determination of heat extraction method (ISO 787-3.2000, IDT)
GB/T 5211.3-1985 Determination of pigment (eqv ISO 787-2. 1981) at 105 ℃ volatiles
GB/T 5211.15-1988 Determination of oil absorption pigments (eqv ISO 787-5. 1980)
GB/T 5950-1996 building materials and non-metallic mineral products whiteness measurement method
GB/T 6003.1-1997 woven wire mesh test sieve (eqv ISO 3310-1.1990)
GB/T 6678 General Principles for Sampling Chemical Products
GB/T 6679 General rules for sampling solid chemical products
Laboratory use specifications and test methods (. 1987 neq ISO 3696) GB/T 6682-1992 Analysis
GB/T 8946-1998 plastic bags
GB/T 19077.1-2003 laser diffraction particle size analysis
Preparation of HG/T 3696.2 inorganic chemical products, chemical analysis of impurity standard solution
Preparations of HG/T 3696.3 inorganic chemical products, chemical analysis
3 formula, molecular weight
Molecular formula. BaSO4
Molecular weight. 233.40 (according to 2005 international relative atomic mass)
4 Requirements
4.1 Appearance. white powder.
4.2 Industrial precipitated barium sulfate should meet the requirements of Table 1.
......
| Standard ID | GB/T 2899-2017 (GB/T2899-2017) | | Description (Translated English) | Barium sulphate precipitated for industrial use | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | G12 | | Classification of International Standard | 71.060.50 | | Word Count Estimation | 10,198 | | Date of Issue | 2017-11-01 | | Date of Implementation | 2018-05-01 | | Older Standard (superseded by this standard) | GB/T 2899-2008 | | Drafting Organization | Zhejiang Shuiyin Environmental Protection Technology Co., Ltd., Hefei Qingshui Water Treatment Co., Ltd., Shenzhou Schwab Chemical Co., Ltd., Weifang Dayao New Material Co., Ltd., Nanfeng Chemical Group Co., Ltd. Barium Salt Branch, Shaanxi Fuhua Chemical Co., Ltd., Shandong Huayu New Material Co., Ltd., Qingdao Hongxing Chemical Group Co., Ltd., Hejin City Acer Powder Materials Co., Ltd., Hebei Yu Dong Paint Co., Ltd., CNOOC Tianjin Chemical Research and Design Institute Co., Ltd. | | Administrative Organization | National Chemical Standardization Technical Committee inorganic chemical sub-technical committee (SAC/TC 63/SC 1) | | Regulation (derived from) | National Standard Announcement 2017 No. 29 | | Proposing organization | China Petroleum and Chemical Industry Federation | | Issuing agency(ies) | People's Republic of China General Administration of Quality Supervision, Inspection and Quarantine, China National Standardization Administration | | Standard ID | GB/T 2899-2008 (GB/T2899-2008) | | Description (Translated English) | Barium sulphate precipitated for industrial use | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | G12 | | Classification of International Standard | 71.060.50 | | Word Count Estimation | 12,132 | | Date of Issue | 2008-04-10 | | Date of Implementation | 2008-10-01 | | Older Standard (superseded by this standard) | GB/T 2899-1996 | | Adopted Standard | ISO 3262-3-1998, MOD | | Drafting Organization | Tianjin Chemical Research and Design Institute | | Administrative Organization | National Standardization Technical Committee Chemistry Inorganic Chemicals Branch | | Regulation (derived from) | National Standard Approval Announcement 2008 No.5 (Total No.118) | | Proposing organization | China Petroleum and Chemical Industry Association | | Issuing agency(ies) | General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, China National Standardization Administration Committee | | Summary | This standard specifies the requirements for industrial precipitated barium sulfate, test methods, inspection rules, signs, labels, packaging, transport and storage into. This standard applies to industrial precipitated barium sulfate. The products are mainly used in coating, ink, paint, rubber, battery, plastics and coated paper and other industries. | | Standard ID | GB/T 2899-1996 (GB/T2899-1996) | | Description (Translated English) | Barium sulphate, precipitated for industrial use | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | G12 | | Classification of International Standard | 71.060.50 | | Word Count Estimation | 12,127 | | Date of Issue | 1996/12/2 | | Date of Implementation | 1997/5/1 | | Older Standard (superseded by this standard) | GB/T 2899-1982 | | Adopted Standard | ISO 3262-1975, IDT; ISO 3262-1975, NEQ | | Regulation (derived from) | Announcement of Newly Approved National Standards No. 5, 2008 (No. 118 overall) | | Proposing organization | Ministry of Chemical Industry of the People Republic of China | | Issuing agency(ies) | State Bureau of Technical Supervision |
|