GB/T 24721.4-2023 (GB/T24721.4-2023, GBT 24721.4-2023, GBT24721.4-2023) & related versions
Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | See Detail | Status | Similar PDF |
GB/T 24721.4-2023 | English | 260 |
Add to Cart
|
0-9 seconds. Auto delivery.
|
Glass fiber reinforced plastic product for highway -- Part 4: Non-pressure communication well lid
|
GB/T 24721.4-2023
| Valid |
GBT 24721.4-2023
|
GB/T 24721.4-2009 | English | 399 |
Add to Cart
|
3 days
|
Glass fiber reinforced plastic product for highway -- Part 4: Non-pressure communications well lid
|
GB/T 24721.4-2009
| Obsolete |
GBT 24721.4-2009
|
Buy with any currencies (Euro, JPY, KRW...): GB/T 24721.4-2023 Preview this PDF: GB/T 24721.4-2023
GB/T 24721.4-2023
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 03.220.20; 93.080.30
CCS P 66
Replacing GB/T 24721.4-2009
Glass Fiber Reinforced Plastic Product for Highway - Part
4: Non-pressure Communication Well Lid
ISSUED ON: MARCH 17, 2023
IMPLEMENTED ON: JULY 1, 2023
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of China.
Table of Contents
Foreword ... 3
Introduction ... 5
1 Scope ... 6
2 Normative References ... 6
3 Terms and Definitions ... 6
4 Structure, Dimensions, Deviations and Model ... 7
5 Technical Requirements ... 9
6 Test Methods ... 10
7 Inspection Rules ... 13
8 Marking, Packaging, Transportation and Storage ... 14
Appendix A (normative) Determination Method for Overall Bearing Capacity ... 15
Foreword
This document was drafted in accordance with the rules provided in GB/T 1.1-2020 Directives
for Standardization - Part 1: Rules for the Structure and Drafting of Standardizing Documents.
This document is Part 4 of GB/T 24721 Glass Fiber Reinforced Plastic Product for Highway.
GB/T 24721 has issued the following parts:
---Part 1: General Rule;
---Part 2: Trunk;
---Part 3: Duct;
---Part 4: Non-pressure Communications Well Lid;
---Part 5: Sign Base Panel.
This document serves as a replacement of GB/T 24721.4-2009 Glass Fiber Reinforced Plastic
Product for Highway - Part 4: Non-pressure Communications Well Lid. In comparison with
GB/T 24721.4-2009, apart from structural adjustments and editorial modifications, the main
technical changes are as follows:
a) The definitions of the terms “total clearance” and “clear opening of well lid” are
modified (see 3.4 and 3.6; 3.4 and 3.6 of Version 2009);
b) The product classification is deleted (see 4.1 of Version 2009);
c) The expression method of product model is modified (see 4.2; 4.3 of Version 2009);
d) The requirements for the properties of raw materials are deleted (see 5.1.1 of Version
2009);
e) The technical requirements for the appearance quality are modified (see 5.1; 5.1.2 of
Version 2009);
f) The technical requirements and test methods for flame retardancy are modified (see
Table 2 and 6.7.3; Table 2 and 6.5.3.3 of Version 2009);
g) The technical requirements and test methods for smoke density are added (see Table
2 and 6.7.4);
h) The technical requirements and test methods for artificial accelerated aging resistance
(fluorescent ultraviolet light source) are added (see Table 2 and 6.11.4);
i) The technical requirements for natural exposure resistance are modified (see Table 2;
Table 2 in 5.2 of Version 2009);
Glass Fiber Reinforced Plastic Product for Highway - Part
4: Non-pressure Communication Well Lid
1 Scope
This document specifies the structure, dimensions and deviations, model, technical
requirements, test methods, inspection rules, as well as marking, packaging, transportation and
storage requirements of glass fiber reinforced plastic non-pressure communication well lid
products for highway.
This document is applicable to the production, inspection and usage of glass fiber reinforced
plastic non-pressure communication well lid (hereinafter referred to as “glass fiber reinforced
communication well lid”) for non-vehicle driving areas on highways.
2 Normative References
The contents of the following documents constitute indispensable clauses of this document
through the normative references in the text. In terms of references with a specified date, only
versions with a specified date are applicable to this document. In terms of references without a
specified date, the latest version (including all the modifications) is applicable to this document.
GB/T 24721.1-2023 Glass Fiber Reinforced Plastic Product for Highway - Part 1: General Rule
3 Terms and Definitions
The following terms and definitions are applicable to this document.
3.1 communication well lid
Communication well lid refers to a closure with openable communication well head.
NOTE: it is composed of a support (mouth ring) and a well lid.
3.2 seating
Seating refers to a part fixed at the well head for placing and supporting the well lid.
3.3 depth of insertion
Depth of insertion refers to the distance from the bearing surface to the top surface of the
support.
6.2 Reagents
In accordance with the method of 6.2 in GB/T 24721.1-2023, conduct the test.
6.3 Test Instruments and Equipment
In accordance with the method of 6.3 in GB/T 24721.1-2023, conduct the test.
6.4 Specimen
6.4.1 General requirements
In accordance with the method of 6.4 in GB/T 24721.1-2023, conduct the test.
6.4.2 Special stipulations
When it is impossible to prepare specimens on the finished product, the same raw materials and
the same process method as the product shall be used to prepare specimens with a uniform
planar structure and a thickness of 5.0 mm 0.2 mm. There are no special restrictions on the
size of the specimens, but at least it shall be guaranteed that 200 mm 200 mm test pieces can
be punched and sheared, and the total area of the specimens shall not be less than 0.24 m2.
The preparation of flexural strength specimens shall also include the same number of
comparative specimens with the properties retention rate of water resistance, damp heat
resistance and weather resistance.
6.5 Structures and Dimensions
6.5.1 Nominal outer diameter or side length of well lid
Use a steel ruler or steel tape with a division value of 1 mm to conduct the measurement. On
the surface of the well lid, uniformly measure-take 3 diameter values or 3 side length values of
length and width; take the arithmetic mean as the measurement result.
6.5.2 Insertion depth of well lid
Use a depth gauge with a division value not greater than 0.02 mm to measure the insertion depth
of the well lid at two mutually perpendicular axes; take the arithmetic mean of 4 values as the
measurement result.
6.5.3 Total clearance of well lid
Use a steel ruler or steel tape with a division value of 1 mm to measure the diameter of side
length of two mutually perpendicular holes on the support; take the arithmetic mean as the
measurement result, then, subtract the nominal outer diameter or corresponding side length of
the well lid to obtain the total clearance.
6.5.4 Width of bearing surface
Use a caliper with a division value not greater than 0.02 mm to measure the width of the bearing
surface at two mutually perpendicular axes of the support.
6.5.5 Contact surface height of well lid
Use a depth gauge with a division value not greater than 0.02 mm to measure the height of the
contact surface at two mutually perpendicular axes of the well lid; take the arithmetic mean of
4 values as the measurement result.
6.6 Appearance Quality
In accordance with the method of 6.5 in GB/T 24721.1-2023, conduct the test. For the raised
height of the anti-skip patterns, use a depth gauge with a division value not greater than 0.02
mm to measure any 3 points; take the arithmetic mean as the measurement result.
6.7 General Physical and Mechanical Properties
6.7.1 Density
In accordance with the method of 6.6.5 in GB/T 24721.1-2023, conduct the test.
6.7.2 Barcol hardness
In accordance with the method of 6.6.6 in GB/T 24721.1-2023, conduct the test.
6.7.3 Flame-retardancy
In accordance with the method of 6.7 in GB/T 24721.1-2023, conduct the test.
6.7.4 Smoke density
In accordance with the method of 6.8 in GB/T 24721.1-2023, conduct the test.
6.8 Overall Bearing Capacity
In accordance with the method of Appendix A, conduct the test.
6.9 Water Resistance
In accordance with the method of 6.10 in GB/T 24721.1-2023, conduct the test.
6.10 Resistance to Chemical Media
In accordance with the method of 6.11 in GB/T 24721.1-2023, conduct the test.
6.11 Environmental Adaptability
6.11.1 Damp heat resistance
In accordance with the method of 6.12.1 in GB/T 24721.1-2023, conduct the test.
......
GB/T 24721.4-2009
Glass fiber reinforced plastic product for highway Part 4. Non-pressure communications well lid
ICS 03.220.20; 93.080.30
P66
National Standards of People's Republic of China
Highway glass fiber reinforced plastic products
Part 4. Non pressurized communication covers
Posted 2009-11-30
2010-04-01 implementation
Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China
Standardization Administration of China released
Table of Contents
Preface Ⅰ
1 Scope 1
2 Normative references 1
3 Terms and definitions
4 product classification, structure, dimensions and tolerances 2
5 Technical requirements 3
6 Test Method 4
7 Inspection rules 5
8 signs, packaging, transportation and storage 5
Appendix A (normative) Determination of the overall bearing capacity of 6
Foreword
GB/T 24721 "highway of glass fiber reinforced plastic products" is divided into five sections.
--- Part 1. General;
--- Part 2. header tank;
--- Part 3. pipelines;
--- Part 4. Non-pressurized communication covers;
--- Part 5. flag floor.
This section GB/T Part of 424,721.
This section of Appendix A normative appendix.
This part of the National Traffic engineering facilities (highway) Standardization Technical Committee (SAC/TC223) and focal points.
This section drafted by. Ministry of Communications Highway Research Institute, National Transportation Safety Facilities Quality Supervision and Inspection Center, Highway Traffic Safety solid
Laboratory.
The main drafters of this section. Lu Yuhong, Guodong Hua, Gong Bo Yan, Zhang Jianping, Ma Xuefeng, Jiang Xufeng, Zhang Zhiyong.
Highway glass fiber reinforced plastic products
Part 4. Non pressurized communication covers
1 Scope
This section GB/T 24721 specifies the highway unpressurized glass fiber reinforced plastic covers communication (hereinafter referred to as non-pressure FRP
Communications covers) product classification, structure, dimensions and tolerances, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage
content.
This section applies to non-road vehicle area with non-pressure fiberglass covers communications, roads and other polymer-based composite material production
Reference materials can be used.
2 Normative references
The following documents contain provisions which, through GB/T 24721 in this section reference in terms of this section. For dated reference documents
Member all subsequent amendments (not including errata content) or revisions do not apply to this section, however, we are encouraged to reach agreement under this section
All parties that proposed to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 14486 Plastic molding dimensional tolerances (GB/T 14486-2008, DIN16901. 1982, NEQ)
GB/T 24721.1-2009 road with glass fiber reinforced plastic products - Part 1. General
3 Terms and Definitions
The following terms and definitions apply to this part of the GB/T 24721 of.
3.1
Communication wellhead closure can be opened by the holder (port ring) and covers the composition.
3.2
Fixed to the wellhead, for receiving and supporting the covers.
3.3
Seat bearing surface to the top surface from the seat.
3.4
And the gap between bearing and covers.
3.5
Covers and seat support surface of the contact plane.
3.6
Supports opening the maximum inscribed circle diameter, D0 1 shown in FIG.
......
Standard ID | GB/T 24721.4-2023 (GB/T24721.4-2023) | Description (Translated English) | Glass fiber reinforced plastic product for highway -- Part 4: Non-pressure communication well lid | Sector / Industry | National Standard (Recommended) | Classification of Chinese Standard | P66 | Classification of International Standard | 03.220.20; 93.080.30 | Word Count Estimation | 15,116 | Date of Issue | 2023-03-17 | Date of Implementation | 2023-07-01 | Older Standard (superseded by this standard) | GB/T 24721.4-2009 | Drafting Organization | Highway Research Institute of the Ministry of Transport, Zhonglu Gaoke Traffic Inspection and Certification Co., Ltd. | Administrative Organization | National Transportation Engineering Facilities (Highway) Standardization Technical Committee (SAC/TC 223) | Proposing organization | National Transportation Engineering Facilities (Highway) Standardization Technical Committee (SAC/TC 223) | Issuing agency(ies) | State Administration for Market Regulation, National Standardization Management Committee | Standard ID | GB/T 24721.4-2009 (GB/T24721.4-2009) | Description (Translated English) | Glass fiber reinforced plastic product for highway. Part 4: Non-pressure communications well lid | Sector / Industry | National Standard (Recommended) | Classification of Chinese Standard | P66 | Classification of International Standard | 03.220.20; 93.080.30 | Word Count Estimation | 10,128 | Date of Issue | 2009-11-30 | Date of Implementation | 2010-04-01 | Quoted Standard | GB/T 14486; GB/T 24721.1-2009 | Drafting Organization | Ministry of Transportation Highway Research Institute | Administrative Organization | National Traffic Engineering Facility (highway) Standardization Technical Committee | Regulation (derived from) | National Standard Approval Announcement 2009 No.14 (Total No.154) | Proposing organization | National Traffic engineering facilities (highway) Standardization Technical Committee (SAC/TC 223) | Issuing agency(ies) | Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China; Standardization Administration of China | Summary | This standard specifies the highway with a non- pressurized glass fiber reinforced plastic covers communications (hereinafter referred to as non-pressure FRP communication covers) product classification, test methods, , structure, dimensions and deviations, technical requirements for inspection rules, signs, packaging, transport and storage and so on. This section applies to a non- highway vehicle area communicate with non-pressure FRP manhole covers, road and other polymer-based composites can refer to the use of the product. |
|