GB/T 18487.2-2017 (GB/T18487.2-2017, GBT 18487.2-2017, GBT18487.2-2017) & related versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | See Detail | Status | Similar PDF |
| GB/T 18487.2-2017 | English | 145 |
Add to Cart
|
0-9 seconds. Auto delivery.
|
Electric vehicle conductive charging system -- Part 2: EMC requirements for off-board electric vehicle supply equipment
|
GB/T 18487.2-2017
| Valid |
GBT 18487.2-2017
|
| GB/T 18487.2-2001 | English | 95 |
Add to Cart
|
0-9 seconds. Auto delivery.
|
Electric vehicle conductive charging system -- Electric vehicles requirements for conductive connection to an AC/DC supply
|
GB/T 18487.2-2001
| Obsolete |
GBT 18487.2-2001
|
Buy with any currencies (Euro, JPY, KRW...): GB/T 18487.2-2017 Preview this PDF: GB/T 18487.2-2017
GB/T 18487.2-2017: PDF in English (GBT 18487.2-2017)
GB/T 18487.2-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 33.100
L 06
Replacing GB/T 18487.2-2001
Electric vehicle conductive charging system –
Part 2. EMC requirements for off-board
electric vehicle supply equipment
ISSUED ON. DECEMBER 29, 2017
IMPLEMENTED ON. JULY 01, 2018
Issued by. Ministry of Housing and Urban-rural Development of PRC;
General Administration of Quality Supervision, Inspection and
Quarantine of the People's Republic of China.
Table of Contents
Foreword ... 4
1 Scope ... 6
2 Normative references ... 6
3 Terms and definitions, abbreviations ... 9
3.1 Terms and definitions ... 9
3.2 Abbreviations ... 10
4 Power supply equipment configuration ... 11
4.1 Overview ... 11
4.2 Conductive power transfer (CPT) equipment ... 11
5 Test load conditions of power supply equipment ... 12
5.1 Overview ... 12
5.2 Electric vehicle’s CPT power supply equipment ... 12
6 Operating conditions during test ... 12
6.1 Overview ... 12
6.2 Test description ... 13
6.3 Environmental conditions/restrictions ... 14
7 Immunity requirements ... 14
7.1 Performance criteria ... 14
7.2 Test requirements ... 16
8 Emission requirements ... 23
8.1 Overview ... 23
8.2 Low-frequency disturbance limits and test conditions ... 23
8.3 Radio frequency disturbance limits and test conditions ... 25
9 Test results and test reports ... 29
Appendix A (Normative) Conductive harassment voltage test arrangement
example for DC power supply CPT port ... 31
Appendix B (Normative) CPT port load conditions ... 33
Appendix C (Normative) Surge and electrical fast transient burst test
arrangement of DC power supply equipment ... 36
Appendix D (Normative) Radiation harassment of keyless entry system ... 38
Appendix E (Informative) Voltage transient harassment of DC power supply
equipment ... 41
Foreword
GB/T 18487 “Electric vehicle conductive charging system” consists of the
following three parts.
- Part 1. General requirements;
- Part 2. EMC requirements for off-board electric vehicle supply equipment;
- Part 3. A.C./D.C. Electric vehicle charging station
This part is part 2 of GB/T 18487.
This part was drafted in accordance with the rules given GB/T 1.1-2009.
This part replaces GB/T 18487.2-2001 “Electric vehicle conductive charging
system - Electric vehicles requirements for conductive connection to an
A.C/D.C. supply”.
Compared with GB/T 18487.2-2001, in addition to editorial changes, the main
technical changes are as follows.
- As a result of an increase of power supply equipment, CHANGE the name
of this part into “Electric vehicle conductive charging system - Part 2. EMC
requirements for off-board electric vehicle supply equipment”;
- ADD the power supply equipment configuration requirements (SEE clause
4);
- ADD the power supply equipment test load conditions (SEE clause 5);
- ADD the operating conditions of the test process (SEE clause 6);
- ADD the immunity requirements (SEE clause 7);
- ADD the emission requirements (SEE clause 8).
This part was proposed by AND shall be under the jurisdiction of China
Electricity Council.
The drafting organizations of this part. Shanghai Electric Apparatus Research
Institute, China Electric Power Research Institute, State Grid Electric Power
Research Institute, Xu Ji Group, Putian New Energy Co., Ltd., Shenzhen
Aotexun Power Equipment Co., Ltd., Zhuhai Taitan Technology Co., Ltd.
Company, Xuchang Kaipu Detection Technology Co., Ltd., BYD Auto Industry
Co., Ltd., Zhejiang Wanma New Energy Co., Ltd., Taida Electronics Enterprise
Management (Shanghai) Co., Ltd. and Beiqi New Energy Vehicle Co., Ltd.
Electric vehicle conductive charging system –
Part 2. EMC requirements for off-board
electric vehicle supply equipment
1 Scope
This part of GB/T 18487 specifies the electromagnetic compatibility
requirements of the electric vehicle power supply equipment for electrical
vehicle off-board conductive charging (hereinafter referred to as the power
supply equipment). The maximum rated voltage of the power supply of the
power supply equipment is 1000 VAC or 1500 VDC, the maximum rated output
voltage is 1000 VAC or 1500 VDC.
This part applies to the power supply equipment of the charging mode 2,
charging mode 3, charging mode 4 as specified in GB/T 18487.1.
This part applies to the electrical vehicle power supply equipment which obtains
energy from the field energy storage system (such as buffer battery, etc.).
In this part, it considers that the power cables without electronic components or
switches (except for manual switch) are passive, which comply with the
emission and immunity requirements, so they do not require test any more.
This part does not apply to any on-board power supply equipment AND the
components and equipment to supply power or charge the electrical vehicle.
This part does not apply to the power supply equipment supplying power or
charging the electrical vehicle through wireless charging (WPT) method.
This part does not apply to trolley buses, railway vehicles, industrial vehicles
and the power supply equipment which is mainly for non-road vehicles.
2 Normative references
The following documents are essential to the application of this document. For
the dated documents, only the versions with the dates indicated are applicable
to this document; for the undated documents, only the latest version (including
all the amendments) are applicable to this document.
GB/T 4365 Electrotechnical terminology - Electromagnetic compatibility
GB 4824-2013 Industrial, scientific and medical equipment - Radio-
frequency disturbance characteristics - Limits and methods of measurement
GB/T 6113.102-2008 Specification for radio disturbance and immunity
measuring apparatus and methods - Part 1-2. Radio disturbance and
immunity measuring apparatus - Ancillary equipment - Conducted
disturbance
GB/T 6113.201 Specification for radio disturbance and immunity measuring
apparatus and methods - Part 2-1. Methods of measurement of disturbances
and immunity - Conducted disturbance measurements
GB/T 17215.321 Electricity metering equipment (A.C.) - Particular
requirements - Part 21. Static meters for active energy (classes 1 and 2)
GB 17625.1 Electromagnetic compatibility - Limits - Limits for harmonic
current emissions (equipment input current ≤ 16 A per phase)
GB/T 17625.2 Electromagnetic compatibility (EMC) - Limits - Limitation of
voltage changes, voltage fluctuations and flicker in public low-voltage supply
systems, for equipment with rated current ≤ 16 A per phase and not subject
to conditional connection
GB/T 17625.7 Electromagnetic compatibility - Limits - Limitation of voltage
changes, voltage fluctuations and flicker in public low-voltage supply
systems for equipment with rated current ≤ 75 A and subject to conditional
connection
GB/T 17625.8 Electromagnetic compatibility - Limits - Limits for harmonic
currents produced by equipment connected to public low-voltage systems
with input current >16 A and ≤ 75 A per phase
GB/T 17626.2 Electromagnetic compatibility - Testing and measurement
techniques - Electrostatic discharge immunity test
GB/T 17626.3 Electromagnetic compatibility - Testing and measurement
techniques - Radiated radio-frequency electromagnetic field immunity test
GB/T 17626.4 Electromagnetic compatibility - Testing and measurement
techniques - Electrical fast transient/burst immunity test
GB/T 17626.5 Electromagnetic compatibility - Testing and measurement
techniques - Surge immunity test
Power port (AC or DC)
A port of the conductor or cable which supply power to the equipment or
relevant equipment to make it work normally.
3.1.4
Wired network port
Ports connecting voice, data and signaling, which...
......
| Standard ID | GB/T 18487.2-2017 (GB/T18487.2-2017) | | Description (Translated English) | Electric vehicle conductive charging system -- Part 2: EMC requirements for off-board electric vehicle supply equipment | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | L06 | | Classification of International Standard | 33.100 | | Word Count Estimation | 30,334 | | Date of Issue | 2017-12-29 | | Date of Implementation | 2018-07-01 | | Drafting Organization | Shanghai Electric Apparatus Research Institute, China Electric Power Research Institute, State Grid Electric Power Research Institute, Xu Ji Group, Putian New Energy Co., Ltd., Shenzhen Aotexun Power Equipment Co., Ltd., Zhuhai Titan Technology Co., Ltd. Xuchang Cape Testing Technology Co., Ltd., BYD Auto Industry Co., Ltd., Zhejiang Wanma New Energy Co., Ltd., Delta Electronics Enterprise Management (Shanghai) Co., Ltd., Beiqi New Energy Vehicle Co., Ltd. | | Administrative Organization | China Electricity Council | | Proposing organization | China Electricity Council | | Issuing agency(ies) | People's Republic of China General Administration of Quality Supervision, Inspection and Quarantine, China National Standardization Administration |
|