Powered by Google www.ChineseStandard.net Database: 189759 (19 May 2024)

GB 20182-2006 related PDF English

GB 20182-2006 (GB20182-2006) & related versions
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)See DetailStatusSimilar PDF
GB 20182-2006English145 Add to Cart 0-9 seconds. Auto delivery. The cab of commercial vehicles -- External projections GB 20182-2006 Valid GB 20182-2006



Preview PDF: GB 20182-2006

GB 20182-2006: PDF in English
GB 20182-2006
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 43.040.60
T 26
The Cab of Commercial Vehicles -- External Projections
ISSUED ON: APRIL 3, 2006
IMPLEMENTED ON: APRIL 1, 2007
Issued by: Standardization Administration of China;
General Administration of Quality Supervision, Inspection and
Quarantine of the People's Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 General provisions ... 5
5 Special provisions ... 6
6 Inspection methods ... 8
ANNEX A (Informative) Procedure for determining "H" point and actual seat-back
angle and for verifying their relationship to "R" point and design seat-back angle ... 11
ANNEX B (Informative) Comparison of chapter numbering between this Standard
and ECE R61 ... 16
Foreword
All contents in this Standard are compulsory.
This Standard is modified in relation to ECE R61 (00 Series, 1984) “Uniform provisions for
the approval of commercial vehicles with regard to their external projections forward of the
cab's rear panel” (English version).
This Standard was redrafted according to ECE R61. Annex B lists out the correlation of the
chapter numbering in this Standard and ECE R61.
The following changes have been made in this Standard to the technical requirements of
ECE R61:
a) Content concerning “Approval Procedure and Approval Mark” in Clause 3, 4, Annex 1
and Annex 2 of ECE R61 was not incorporated into this Standard, for reason of the
difference between our national standard system and European Regulation system;
b) Paragraph 5.1.1 in ECE R61 “parts situated 2.00 m above the ground or lower than the
reference plane or the floor line” was changed into “Parts that are situated 1.80 m
above the ground or lower than the reference plane or the floor line” in this Standard.
In order to facilitate the usage of this Standard, the following editorial changes have been
made over ECE R61:
a) “This Regulation” was changed into “This Standard”;
b) “cm” was changed into “mm”;
c) Informative Annex B was added.
Annexes A and B of this Standard are informative.
Proposal for the implementation date of this Standard:
For the products newly applying for type approval, this Standard comes into effect on April 1,
2007; for the products that have been type-approved, this Standard comes into effect on
April 1, 2009.
This Standard was proposed by the National Development and Reform Commission.
This Standard shall be under the jurisdiction of National Technical Committee of Auto
Standardization.
Drafting organization of this Standard: China Automotive Technology and Research Centre.
Chief drafters of this Standard: Sun Zhendong, Sun Zhiyu.
The Cab of Commercial Vehicles -- External Projections
1 Scope
This Standard specifies the terms, general provisions, special provisions and inspection
methods for external projection of the cab of commercial vehicles.
This Standard applies to Category N vehicles. However, it does not apply to the exterior
rear view mirrors, and the mirror support arm, aerials and luggage racks.
2 Normative references
The following Standards contain provisions which, through reference in this text, constitute
provisions of this Standard. For dated references, subsequent amendments (corrigenda
excluded) to, or revisions of, any of these publications do not apply. However, parties to
agreements based on this Standard are encouraged to investigate the possibility of applying
the most recent editions of the Standards indicated below. For undated references, the
latest edition of the normative documents referred to applies.
GB 11566-1995 Passenger car − External projections
3 Terms and definitions
The following terms and definitions apply to this Standard.
3.1
External surface
It means that part of the vehicle forward of the cab rear panel as defined in Paragraph 3.3
below, with the exception of the rear panel itself, and includes such items as the front wings,
front bumpers and front wheels.
3.2
Cab
It means that part of the bodywork which constitutes the driver and passenger compartment,
including the doors.
3.3
Cab rear panel
It means the rearmost part of the external surface of the driver and passenger compartment.
Where it is not possible to determine the position of the rear cab panel, for the purposes of
this Standard it would be deemed to be the vertical transversal plane situated 500 mm to
the rear of the R Point of the driver seat, with the seat, if adjustable, located at its
rearmost driving position (See Annex A). If the cab is fitted with more than one row of
seats, the passenger seat of the rearmost row is adjusted to the rearmost position, the
......

BASIC DATA
Standard ID GB 20182-2006 (GB20182-2006)
Description (Translated English) The cab of commercial vehicles. External projections
Sector / Industry National Standard
Classification of Chinese Standard T26
Classification of International Standard 43.040.60
Word Count Estimation 15,115
Date of Issue 2006-04-03
Date of Implementation 2007-04-01
Quoted Standard GB 11566-1995
Adopted Standard ECE R61-1984, MOD
Drafting Organization China Automotive Technology and Research Center
Administrative Organization National Automotive Standardization Technical Committee
Regulation (derived from) China Announcement of Newly Approved National Standards No. 5, 2006 (No. 92 overall)
Proposing organization National Development and Reform Commission
Issuing agency(ies) Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China; Standardization Administration of China
Summary This Chinese standard specifies the commercial vehicle cab exterior panels before term projections, general provisions, special requirements and test methods. This standard applies to Class N cars. But not for automotive exterior mirror and exterior mirrors connectors, antennas and luggage rack.