Powered by Google www.ChineseStandard.net Database: 189759 (19 May 2024)

GB 14167-2013 related PDF English

GB 14167-2013 (GB14167-2013) & related versions
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)See DetailStatusSimilar PDF
GB 14167-2013English555 Add to Cart 0-9 seconds. Auto delivery. Safety-belt anchorages, ISOFIX anchorages systems and ISOFIX top tether anchorages for vehicles GB 14167-2013 Valid GB 14167-2013
GB 14167-2006English799 Add to Cart 5 days Safety-belt anchorages for vehicles GB 14167-2006 Obsolete GB 14167-2006
GB 14167-1993English359 Add to Cart 3 days Motor vehicles--Safety belt anchorages GB 14167-1993 Obsolete GB 14167-1993



Preview PDF: GB 14167-2013

GB 14167-2013: PDF in English
GB 14167-2013
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 43.040.60
T 26
Replacing GB 14167-2006
Safety-belt anchorages, ISOFIX anchorages systems and
ISOFIX top tether anchorages for vehicles
ISSUED ON: MAY 07, 2013
IMPLEMENTED ON: JANUARY 01, 2014
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3 
1 Scope ... 5 
2 Normative references ... 5 
3 Terms and definitions... 5 
4 Technical requirements ... 11 
5 Test methods ... 21 
6 Transition period for implementation of this standard ... 27 
Appendix A (Informative) Comparison of clause numbers between this standard and
ECE R14 ... 28 
Appendix B (Normative) ISOFIX anchorage system and ISOFIX top tether anchorage
... 29 
Appendix C (Normative) Determination procedure of motor vehicle's seating position
H point and actual torso angle ... 40 
Appendix D (Normative) Minimum number of anchorages and lower anchorage
position ... 52 
Appendix E (Normative) The position of effective anchorages ... 53 
Appendix F (Normative) Schematic diagram of the human body module ... 55 
Appendix G (Normative) Dynamic test - An alternative to static test ... 57 
Appendix H (Normative) Dummy Specifications ... 59 
Safety-belt anchorages, ISOFIX anchorages systems and
ISOFIX top tether anchorages for vehicles
1 Scope
This standard specifies the position, strength requirements, test methods of the ISOFIX
anchorage system of the safety-belt anchorages, ISOFIX anchorages systems and
ISOFIX top tether anchorages of child restraint system for vehicles.
This standard applies to categories M and N vehicles, which are equipped with seat belt
anchorages for adult occupants, in forward-facing and rear-facing seats.
This standard also applies to categories M1 and N1 vehicles, which are equipped with
ISOFIX anchorages for child restraint systems and their top tether anchorages.
2 Normative references
The following documents are essential to the application of this document. For the dated
documents, only the versions with the dates indicated are applicable to this document;
for the undated documents, only the latest version (including all the amendments) is
applicable to this standard.
GB 11551-2003 The protection of the occupant in the event of a frontal collision for
passenger car
GB 11552-2009 The interior fittings of passenger car
GB 13057-2003 The strength of the seats and their anchorages of passenger vehicles
GB 14166-2013 Safety-belts, restraint systems, child restraint systems and ISOFIX
child restraint systems for occupants of power-driven vehicles
GB/T 15089-2001 Classification of power-driven vehicles and trailers
GB 27887-2011 Restraining devices for child occupants of power-driven vehicles
ISO 6487:2002 Road vehicles - Measurement techniques in impact tests -
Instrumentation
3 Terms and definitions
The following terms and definitions apply to this document.
4.1.1 The design, manufacture, arrangement of seat belt anchorages shall meet the
following requirements:
a) Appropriate seat belts shall be able to be fitted. The seat belt anchorages
(especially in terms of strength) of the front outer seats shall be suitable for the
installation of seat belts, which have retractors and guides; except for the vehicle,
which is equipped with other types of seat belts with retractors. If the anchorage
is only suitable for some special types of seat belts, the type of such seat belts
shall be indicated in the test report.
b) There shall be no risk of slippage of the seat belt, when properly worn.
c) There shall be no risk of damage to the webbing, when the webbing comes into
contact with protruding parts on the vehicle or seat structure.
d) For the anchorage that can change the position (the anchorage is convenient for
the occupant to enter the vehicle and can restrain the occupant), the provisions in
this standard shall apply to the anchorage, when it is in an effective restraint
position.
4.1.2 All ISOFIX anchorage systems and ISOFIX top tether anchorages, which are used
for the installation of ISOFIX CRS, shall be designed, manufactured, arranged as
follows:
a) Ensure that the vehicle meets this standard, during normal use. For the anchorage
system and ISO top tether anchorage, which can be added to any vehicles, they
shall also meet this standard. At the same time, there shall be a description of the
anchorage system, in the relevant application documents.
b) The strength design of the anchorage system and the ISOFIX top tether anchorage
system shall meet the ISOFIX child restraint system, which has the quality group
0, group 0+, group I, as defined in GB 27887-2011.
4.1.3 The design and arrangement of the ISOFIX anchorage system shall meet the
following requirements:
a) There shall be two transverse horizontal rigid rods, which have a diameter of 6
mm ± 0.1 mm; the minimum effective length of the two rods is 25 mm; the two
rods are coaxial, as shown in Figure B.4 of Appendix B.
b) All ISOFIX anchorage systems, which are installed on the vehicle's seating
position, shall be located at a distance of not less than 120 mm (horizontal
measurement to the center of the rod) from point H (see Appendix C, for the
determination of point H).
c) For all ISOFIX anchorage systems, which are installed on vehicles, it shall be
ensured that the ISOFIX child restraint fixation module ISO/F2(B) or
ISO/F2X(B1), which are described in Figure B.5 or Figure B.6 of Appendix B of
GB 14166-2013, can be installed.
d) The inclination angle of the bottom surface of the fixation module ISO/F2(B) or
ISO/F2X(B1), which are defined in Figure B.5 or Figure B.6 of Appendix B of
GB 14166-2013, is as follows; the measurement of the inclination angle is relative
to the vehicle reference plane, which is defined in Figure C.3 in Appendix C:
1) Front and rear tilt angle: 15° ± 10°;
2) Left and right deviation angle: 0° ± 5°;
3) Flip angle: 0° ± 10°.
e) ISOFIX anchorage system's position shall be permanently fixed; it can also be
hidden. For concealable anchorages, it shall meet the corresponding requirements
of the ISOFIX anchorage system, during normal use.
f) For each ISOFIX lower anchorage rod (in normal use) or each permanently fixed
guide, when unobstructed by seat cushions and backrests: along the vertical
longitudinal plane, which passes through the midpoint of the rod or guide, it shall
be clearly visible, in the 30° upwards along the horizontal plane. Alternatively,
there shall be permanent markings, near each lower anchorage rod and guide on
the vehicle. Marking is selected by the manufacturer, in one of the following
forms:
1) As shown in Figure B.12 of Appendix B, it is a circular icon, which has a
diameter of not less than 13 mm; meanwhile the icon shall have a sharp
contrast with its background,; the icon shall be close to the position of the rod
of each anchorage system;
2) The height of capital letters "ISOFIX" shall not be less than 6 mm.
4.1.4 The design and arrangement of the anchorages of the ISOFIX top tether anchorage
shall meet the following requirements:
a) The car manufacturer may choose to use one of the two methods 4.1.4b) and
4.1.4c). However, the 4.1.4b) only applies when the ISOFIX position is on the
seat.
b) According to the requirements of 4.1.4d) and 4.1.4e), in the design seating
position, the distance -- between the ISOFIX top tether anchorage, which
connects the ISOFIX top tether connector, and the reference point of the shoulder
-- shall be not more than 2000 mm; meanwhile, within the shadow area, as shown
in Figure B.6 ~ Figure B.10 of Appendix B, the placement of the two-dimensional
template, as shown in Figure B.5 of Appendix B, shall be in accordance with the
following conditions:
function of the ISOFIX top tether strap;
2) The non-rigid webbing retractor or the deployable retractor shall be not less
than 65 mm, away from the torso line; the fixed rigid retractor shall be not less
than 100 mm, away from the torso line;
3) After it is installed in the state of use, carry out the test, by applying the load
to the ISOFIX top tether anchorage, as specified in 5.5. The retracting device
shall have sufficient strength.
e) The top tether fixation device can be hidden on the seat back, if it is not in the
pull-up area of the top tether strap, on the top of the seat back.
f) The anchorage of the ISOFIX top tether anchorage shall meet the requirements for
the connection size of the ISOFIX top tether hook, which is specified in Figure
B.3 of Appendix B. Space shall be provided, around the anchorage of the ISOFIX
top tether, to allow its locking and unlocking operations. For those located behind
the ISOFIX anchorage system, all anchorages, that can be used to connect the
ISOFIX top tether hook or ISOFIX top tether connector, shall take one or more
of the following measures, to avoid misuse:
1) Design all such anchorages in the area of ISOFIX top tether anchorages as
ISOFIX top tether anchorages;
2) Only use one of the symbols, as shown in Figure B.13 of Appendix B, or its
mirror-symmetrical symbol, for marking on the ISOFIX top tether anchorage;
3) An obvious mark on the anchorage, that does not meet the above two
requirements, means that it cannot be used in combination with any ISOFIX
anchorage system.
g) For each covered ISOFIX top tether anchorage, the cover shall be marked with
the symbol or mirror-symmetrical symbol, as shown in Figure B.13 of Appendix
B, meanwhile the cover shall be able to be removed, without the use of tools.
4.2 Minimum quantity of seat belt anchorages
4.2.1 Minimum quantity requirements for regular anchorages
4.2.1.1 The categories M and N vehicles (except for categories M2 and M3 vehicles of
Class I, Class II, Class A, as defined in GB/T 15089) shall have seat belt anchorages,
that meet the requirements of this standard. Vehicles of category M1 shall be equipped
with ISOFIX anchorage systems, that meet the requirements of 4.2.2. Vehicles of
category N1, which are equipped with ISOFIX anchorage systems, shall also meet the
requirements of this standard. For the anchorages of the full harness-type safety belts
(with or without retractors), which are approved as S-type safety belts, in accordance
with GB 14166, it shall meet the requirements of this standard. However, additional
anchorages or anchorages for installing the crotch belt assembly are not required to
meet the strength and location requirements of this standard.
4.2.1.2 The minimum quantity of seat belt anchorages, at all forward-facing and rear-
facing seats, shall comply with the provisions of Appendix D.
4.2.1.3 However, for the outer seats of the category N1 vehicles, that are not in the front
row (Note a in Table D.1 of Appendix D), when there is a passage for passengers to
pass between the seats and the nearest side enclosure, it is allowed to set only 2 lower
anchorages. If the space between the seat and the side enclosure is a passage, the
distance -- between the vertical plane of the longitudinal center of the seat (measured
at point R) and the side enclosure -- shall be greater than 500 mm, when all doors are
closed.
4.2.1.4 For the front middle seat (Note b in Table D.1 of Appendix D), if the windshield
is located outside the reference area, which is defined in Appendix B of GB 11552, only
2 lower anchorages may be set. However, if it is located in the reference area, then 3
anchorages are required, at which time the windshield is considered to be part of the
reference area.
4.2.1.5 For all the seating positions of Note c in Table D.1 of Appendix D, 3 anchorages
shall be set. If one of the following conditions is met, only 2 anchorages can be set:
- There is a seat or other vehicle part in front, that meets the requirements of 5.3.3 in
GB 13057-2003;
- No part of the vehicle is in the reference area; OR when the vehicle is in motion,
no part of the vehicle can enter the reference area;
- Vehicle components in the reference area shall meet the energy absorption
requirements, which are specified in 5.2 of GB 13057-2003.
4.2.1.6 For all seats, that can be used when the vehicle is stationary, as well as seats,
which are not included in 4.2.1.1 ~ 4.2.1.4, seat belt anchorages are not required.
However, if the seat belt anchorages are set for this seat position on the vehicle, these
anchorages shall comply with the provisions of this standard; only 2 lower anchorages
are allowed at this time.
4.2.1.7 The requirements for the middle seat in the upper front row of a double-decker
passenger car are the same as those for the outer front row.
4.2.2 Minimum quantity of ISOFIX locations
4.2.2.1 All category M1 vehicles shall be equipped with at least 2 ISOFIX positions; at
least 2 ISOFIX positions shall be equipped with ISOFIX anchorage system and ISOFIX
top tether anchorage, at the same time. The type and quantity of ISOFIX fixtures, which
are installed in each ISOFIX position, shall be determined according to GB 14166.
80°; if the rear seats are adjustable, the above requirements are valid, in all normal
moving positions.
4.3.2.3 Front seats of vehicles other than category M1
For all normal moving positions of the front seats of vehicles other than the category
M1, α1 and α2 shall be within 30° ~ 80°. For all normal use positions of the front seats
of vehicles, which have a maximum gross mass not exceeding 3500 kg, the value of α1
and α2 shall be 60° ± 10°, when at least one of them is a constant value (such as the
anchorage on the seat).
4.3.2.4 Rear seats and special front or rear seats for vehicles other than category
M1
For the bench seats other than the vehicles of category M1, the front and rear seats which
have an adjustment mechanism and a backrest angle less than 20° (see Figure E.1 in
Appendix E), the other rear seats in the normal use position, the α1 and α2 are allowed
to be within 20° ~ 80°. For all normal seating positions of the front seat of the vehicle,
which has a maximum total mass not exceeding 3500 kg, when at least one of α1 and
α2 is a constant value (such as the anchorage on the seat), its value shall be 60° ± 10°.
For the normal seating positions of the non-front seats of categories M2 and M3 vehicles,
α1 and α2 shall be 45° ~ 90°.
4.3.2.5 The distance between the two lower anchorages of the seat belt
The distance -- between two vertical planes, that pass through the two lower anchorages
L1 and L2 of the same seat belt, meanwhile are parallel to the longitudinal center plane
of the vehicle -- shall not be less than 350 mm. For the rear middle seating positions of
categories M1 and N1 vehicles, if the middle seat is not interchangeable with other seats,
the above distance shall not be less than 240 mm. The longitudinal center plane of the
seat shall be between points L1 and L2; the distance shall be at least 120 mm.
4.3.3 Position of effective anchorages on seat belts (see Appendix E)
4.3.3.1 If the position of the effective anchorages on the seat belt is affected by the use
of webbing guides or similar devices, the position of the effective anchorages shall be
determined, according to the position of the anchorage, when the longitudinal centerline
of the webbing passes through the point J1. From point R, use the following three line
segments to determine point J1:
- RZ: Take a line segment, which has a length of 530 mm, from point R up along the
torso line;
- ZX: From point Z along a line perpendicular to the longitudinal center plane of the
vehicle, cut a line segment, which has a length of 120 mm towards the anchorage;
- XJ1: From point X along a straight line perpendicular to the plane, which is
determined by RZ and ZX, cut a line segment, which has a length of 60 mm forward.
Points J2 and J1 are symmetrical, with respect to the longitudinal vertical plane, which
passes through the torso line, which is the torso line of the mannequin, as placed on the
seat. When double doors are used, to provide passages for the front and rear seats,
meanwhile the upper anchorage is on the B-pillar, the anchorage system shall not hinder
the occupant getting on and off the vehicle.
4.3.3.2 The effective anchorage on the seat belt shall be located below the FN plane,
which is perpendicular to the longitudinal center plane of the seat AND at an angle of
65° to the torso line. For the rear seats, this angle can be reduced to 60°. The FN plane
intersects the torso line at point D. At this time, it must guarantee that DR = 315 mm +
1.8S. However, when S ≤ 200 mm, DR = 675 mm.
4.3.3.3 The effective anchorage on the seat belt shall be at the rear of the FK plane,
which is perpendicular to the longitudinal center plane of the seat AND at an angle of
120° to the torso line AND intersecting at point B. At this time, it shall guarantee that
BR = 260 mm + S. However, when S ≥ 280 mm, the manufacturer can choose BR =
260 mm + 0.8S.
4.3.3.4 The value of S shall not be less than 140 mm.
4.3.3.5 The effective anchorage of the seat belt shall be located behind the vertical plane,
which passes through the point R and perpendicular to the longitudinal center plane of
the vehicle, as shown in Appendix E.
4.3.3.6 The effective anchorage of the seat belt shall be above the horizontal plane,
which passes through the point C, as specified in E.1.3 of Appendix E.
4.3.3.7 In addition to the upper effective anchorage specified in 4.3.3.1, if one of the
following conditions is met, another additional effective anchorage may be equipped:
a) Additional anchorages shall meet the requirements of 4.3.3.1 ~ 4.3.3.6.
b) Additional anchorages shall be available, without the aid of tools. The anchorage
shall meet the requirements of 4.3.3.5 and 4.3.3.6; it shall be located in the area,
which is determined by 80 mm up and down in the vertical direction, as shown in
Figure E.1 of Appendix E.
c) The anchorage of the full-harness type safety belt, that meets the requirements
specified in 4.3.3.6, shall be located behind the transverse plane, which passes
through the torso line and in the following positions:
1) For a single anchorage, it is located within the included angle, between two
vertical planes passing through points J1 and J2, as specified in 4.3.3.1; its
horizontal section is as shown in Figure E.2 of Appendix E;
and 4.5.1.
4.5.5 Apply a static load to the SFAD on the ISOFIX, according to 5.6.2.2, to examine
the strength of the ISOFIX anchorage system. ISOFIX anchorage systems, which have
ISOFIX top tether anchorages, shall also be tested in accordance with 5.6.2.3. The
longitudinal horizontal displacement AND the displacement in the direction of the
oblique force during loading shall not exceed 125 mm, allowing permanent deformation
and partial cracking. If the required force is maintained for the specified time, the
ISOFIX lower anchorage, the top tether anchorage, the surrounding area shall not fail.
The additional test of 5.6.2.4 shall be carried out, for the case of the anchorage system
on the seat assembly. No cracks shall appear after the test; meanwhile it shall meet the
requirements that the maximum displacement of the X point, which is caused by the
forward force and the oblique force, shall not be greater than 125 mm.
5 Test methods
5.1 General
5.1.1 Carry out the test according to 5.2. Fix the vehicle, according to the manufacturer's
requirements.
5.1.1.1 The test is carried out on the body frame, OR on the whole vehicle.
5.1.1.2 Only one seat or a group of seat belt anchorage test is allowed, if the following
conditions are met:
a) Have the same structural performance as the corresponding anchorages of other
seats or seat groups;
b) A anchorage fully or partially installed on a seat or seat group, whose structural
characteristics are the same as those of other seats or seat groups.
5.1.1.3 Doors and windows are installed or not; doors and windows are closed or
opened.
5.1.1.4 It is permitted to retain normal equipment, that enhances the structure of the
vehicle.
5.1.2 The seat shall be placed in the most unfavorable driving or use position; the
position of the seat shall be stated in the inspection report. If the backrest angle is
adjustable, it shall be adjusted to the position, which is specified by the manufacturer;
OR it shall ensure that the actual torso angle of the seat for categories M1 and N1
vehicles is 25° as far as possible, or 15° for other categories of vehicles.
5.2 Fixation of vehicle
5.2.1 During the test, all methods of fixing the vehicle shall not strengthen the seat belt
anchorages and ISOFIX anchorages and their surrounding parts; meanwhile, it shall not
weaken the normal deformation of the structure.
5.2.2 All devices, for fixing the vehicle, shall be not less than 500 mm in front of the
anchorage to be measured, OR not less than 300 mm behind; meanwhile, it shall not
affect the body structure within the entire width.
5.2.3 It is recommended that the frame be fastened to a support, which is close to the
wheel axis or suspension attachment point.
5.2.4 If a fixing method different from that specified in 5.2.1 ~ 5.2.3 is adopted, its
equivalence shall be proved.
5.3 Test conditions
5.3.1 All seat belt anchorages of the same group of seats shall be tested at the same time.
If there is a possibility that the test fails, due to asymmetric loading of the seat or
anchorage, an additional test may be performed.
5.3.2 Apply the load, in a direction parallel to the longitudinal center plane of the
vehicle AND 10° ± 5° upward from the horizontal line. First apply a preload of 10% of
the total load (error ±30%); then increase the load to the total load.
5.3.3 Apply the load to the specified value, within 60 s. It can also be loaded to the
specified value, within 4 s, at the request of the manufacturer, AND maintained for at
least 0.2 s.
5.3.4 See 5.4 and Appendix F, for the human body module, which is used for the test.
Place the device in Figure F.1 of Appendix F on the seat cushion; push it as far back as
possible to the backrest; pull the seat belt back tightly. Put the device as shown in Figure
F.2 of Appendix F in place. Place the seat belt on the device and tighten it. Preloading
is not necessary, at this time. The width of the 254 mm or 406 mm human body module,
which is selected for each seating position, shall be as close as possible to the distance
between the two anchorages. The placement of the human body module shall avoid the
influence of the loading force and force distribution, during the test.
5.3.5 The test conditions for the anchorages on the safety belt are as follows:
a) Front outer seats
The seat belt anchorages shall be subjected to the test, which is specified in 5.4.1.
During the test, a simulated three-point safety belt, which is equipped with a
retractor or an upper webbing guide, shall be used to transfer the load to the three
anchorages. In addition, if the number of anchorages is more than that specified
in 4.2, these anchorages shall be tested according to the provisions of 5.4.5. Use a
simulated seat belt to load, during the test.
5.4.1.3 At the same time, a test load of 13500 N ± 200 N shall be applied to the lower
body module (see Figure F.1 in Appendix F). For categories M2 and N2 vehicles, the
test load shall be 6750 N ± 200 N; for categories M3 and N3 vehicles, the test load is
4500 N ± 200 N.
5.4.2 Test of three-point seat belt anchorage without retractor or with retractor on
the upper anchorage
5.4.2.1 A test load of 13500 N ± 200 N shall be applied to the upper body module (see
Figure F.2 in Appendix F), which is connected to the upper anchorage of the seat belt
and the corresponding lower anchorage. If the upper anchorage has a retractor, it shall
be tested together with the retractor. For categories M2 and N2 vehicles, the test load
shall be 6750 N ± 200 N; for categories M3 and N3 vehicles, the test load is 4500 N ±
200 N.
5.4.2.2 At the same time, a test load of 13500 N ± 200 N shall be applied to the lower
body module (see Figure F.1 in Appendix F). For categories M2 and N2 vehicles, the
test load shall be 6750 N ± 200 N; or categories M3 and N3 vehicles, the test load is
4500 N ± 200 N.
5.4.3 Test of attachment point of two-point seat belt (lap belt)
A test load of 22250 N ± 200 N shall be applied to the lower body module, which is
attached to the lap belt (see Figure F.1 in Appendix F). For categories M2 and N2
vehicles, the test load shall be 11100 N ± 200 N; for categories M3 and N3 vehicles, the
test load shall be 7400 N ± 200 N.
5.4.4 Tests for seat belt anchorages on the seat frame OR separately on the seat
frame and body frame
5.4.4.1 While conducting the tests specified in 5.4.1, 5.4.2, 5.4.3, the loads specified
below shall be applied to each seat or group of seats.
5.4.4.2 In addition to the loads specified in 5.4.1, 5.4.2, 5.4.3, it shall also apply a force,
which is equivalent to 20 times the mass of the seat assembly. Inertia loads shall be
applied to the seat or to seat-related parts, that are equivalent to the actual mass of the
corresponding seat. Additional loads and distribution of loads shall be determined by
the manufacturer and approved by the inspection agency. For categories M2 and N2
vehicles, the load is 10 times the mass of the seat assembly; for categories M3 and N3
vehicles, it shall be 6.6 times the mass of the seat assembly.
5.4.5 Test of special type seat belt anchorages
5.4.5.1 Using a device that simulates a shoulder strap, apply a test load of 13500 N ±
200 N to the upper body module (see Figure F.2 in Appendix F), which is connected to
the anchorage.
......

BASIC DATA
Standard ID GB 14167-2013 (GB14167-2013)
Description (Translated English) Safety-belt anchorages, ISOFIX anchorages systems and ISOFIX top tether anchorages for vehicles
Sector / Industry National Standard
Classification of Chinese Standard T26
Classification of International Standard 43.040.60
Word Count Estimation 45,497
Older Standard (superseded by this standard) GB 14167-2006
Quoted Standard GB 11551-2003; GB 11552-2009; GB 13057-2003; GB 14166-2013; GB/T 15089-2001; GB 27887-2011; ISO 6487-2002
Drafting Organization Dongfeng Automobile Company
Administrative Organization National Automotive Standardization Technical Committee
Regulation (derived from) National Standards Bulletin 2013 No. 5
Proposing organization National Development and Reform Commission of the People's Republic of China
Issuing agency(ies) General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Summary This standard specifies the fixed-point seat belts and ISOFIX child restraint system, a fixed point of the system and its location on the pull with a fixed point, the strength requirements and test methods. This standard applies to the installation of fro