YY/T 1676-2020 PDF English
US$245.00 · In stock · Download in 9 secondsYY/T 1676-2020: Ultrasound endoscope Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| YY/T 1676-2020 | English | 245 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Ultrasound endoscope
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: YY/T 1676-2020
YY/T 1676-2020: Ultrasound endoscope---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/YYT1676-2020
YY
PHARMACEUTICAL INDUSTRY STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
ICS 11.040.55
C 41
Ultrasound endoscope
超声内窥镜
ISSUED ON: MARCH 31, 2020
IMPLEMENTED ON: OCTOBER 01, 2022
Issued by: National Medical Products Administration
Table of Contents
Foreword ... 3
Introduction ... 4
1 Scope ... 5
2 Normative references ... 5
3 Terms and definitions ... 6
4 Requirements ... 6
5 Test methods ... 8
Annex A (informative) Technical requirements for phantom and/or test piece 15
Ultrasound endoscope
1 Scope
This Standard specifies terms and definitions, requirements and test methods
of the ultrasonic endoscope related to the ultrasonic performance part.
This Standard is applicable to ultrasound endoscope and ultrasound probe that
extends into the body through the endoscope tube.
NOTE: There are many types of ultrasound transducers for current ultrasound endoscopes
and ultrasound probes, such as single element rotation, ring array and convex array. This
Standard does not consider the appearance and structure of the probe. The test method
of parameters takes the rotation of single element, ring array and convex array imaging as
examples. If necessary, more complex designs can also use the basic methods described
in this Standard.
2 Normative references
The following referenced documents are indispensable for the application of
this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any
amendments) applies.
GB 9706.1, Medical electrical equipment - Part 1: General requirements for
safety
GB 9706.9, Medical electrical equipment - Part 2-37: Particular requirements
for the safety of ultrasonic medical diagnostic and monitoring equipment
GB 10152, B mode ultrasonic diagnostic equipment
GB/T 14710, Environmental requirement and test methods for medical
electrical equipment
YY/T 0108, Testing methods for M-mode of ultrasonic diagnostic equipment
YY 0767, Ultrasonic color flow imaging systems
YY/T 1279, Test method for performance of three-dimensional
ultrasonography
YY/T 1420, Environmental requirement and test methods for medical
ultrasonic equipment
4.5 Blind zone
The blind zone shall meet the requirements published by the manufacturer in
the accompanying documents.
4.6 Slice thickness
If applicable, the slice thickness shall meet the requirements published by the
manufacturer in the accompanying documents.
4.7 Accuracy of horizontal geometric position accuracy
For single-element rotating probe, the accuracy of lateral geometric position
shall be ≤10%.
For ring array probe and convex array probe, the accuracy of horizontal
geometric position shall be ≤5%.
4.8 Accuracy of longitudinal geometric position
For single-element rotating probe, the accuracy of longitudinal geometric
position shall be ≤10%.
For ring array probe and convex array probe, the accuracy of longitudinal
geometric position shall be ≤5%.
4.9 Perimeter and area measurement deviation
If applicable, the deviation of perimeter and area measurement shall be within
±20%, or meet the requirements published by the manufacturer in the
accompanying documents.
4.10 M mode performance indicators
For type-B ultrasound probes with M mode, the performance indicators of its M
mode shall meet the requirements published by the manufacturer in the
accompanying documents.
4.11 3D imaging performance
For equipment with 3D imaging function, its 3D imaging performance indicators
(if applicable) shall meet the requirements specified in YY/T 1279.
4.12 Geometric position accuracy in pullback direction
If applicable, the geometric position accuracy in pullback direction shall meet
the requirements published by the manufacturer.
4.13 Ultrasound imaging geometric distortion
Turn on the device under test. Align the probe at the longitudinal depth target
group. Under the specified setting conditions, keep the target line image clearly
visible. Slightly move the probe. Observe the target line where the image can
be resolved farthest from the probe surface. The distance between the target
line and the probe surface is the detection depth of the probe.
5.4 Lateral resolution
Turn on the device under test. Align the probe at a specific depth of the lateral
resolution target group. Under the specified setting conditions, keep the target
line image clearly visible. Slightly move the probe. The minimum distance
between two target lines that can be separately displayed as two echo signals
is the lateral resolution at that depth.
For different nominal detection depths, it is recommended to measure the
lateral resolution according to the following depth positions:
a) When nominal detection depth is ≥3cm, it is specified by the manufacturer.
Measure at two positions within 1/2 and outside 1/2 of the nominal
detection depth. Take odd centimeters;
b) When 1cm≤nominal detection depth< 3cm, only measure the lateral
resolution at the detection depth of 1cm;
c) When nominal detection depth is < 1cm, a measurement location is
specified by the manufacturer.
5.5 Axial resolution
Turn on the device under test. Align the probe to a target group of axial
resolution at a specific depth. Under the specified setting conditions, keep the
target line image clearly visible. Slightly move the probe. The minimum distance
between two target lines that can be separately displayed as two echo signals
is the axial resolution at that depth.
For different nominal detection depths, it is recommended to measure the axial
resolution according to the following depth positions:
a) When nominal detection depth is ≥3cm, measure outside the lateral
resolution measurement position;
b) When 1cm≤nominal detection depth< 3cm, only measure the axial
resolution of the detection depth < 2cm;
c) When nominal detection depth is < 1cm, a measurement location is
specified by the manufacturer.
5.6 Blind zone
to an appropriate value.
The accuracy of lateral geometric position is usually expressed as a percentage.
5.9 Accuracy of longitudinal geometric position
Turn on the tested type-B ultrasound. Align the probe to the longitudinal linear
target group. Under the specified setting conditions, keep the target group
image clearly visible. Use the device's ranging function. In the full screen range
according to the longitudinal known distance, calculate the accuracy of axial
geometric position according to formula (1).
The accuracy of longitudinal geometric position is usually expressed as a
percentage.
5.10 Perimeter and area measurement deviation
Turn on the device under test. Scan the horizontal and vertical linear target
groups with the probe. Under the specified setting conditions, keep the target
group image clearly visible. Maintain the center of the target group in the center
of the field of view. Draw a closed figure (rectangular or circular) in an area
approximately equal to 75% of the field of view in the center of the display.
Measure the perimeter and the area. Calculate the error according to formula
(1).
5.11 M mode performance indicators
The performance test of the equipment M mode is carried out in accordance
with the provisions of YY/T 0108.
5.12 3D imaging performance
The test method for 3D imaging performance is implemented in accordance
with YY/T 1279.
5.13 Geometric position accuracy in pullback direction
Turn on the device under test. Measure two target lines with known distances
at the middle of the pullback area specified by the manufacturer. Under the
specified setting conditions, keep the target group image clearly visible. Use
the device's ranging function to measure. Calculate the geometric position
accuracy in the pullback direction according to formula (1).
The geometric position accuracy in the pullback direction is usually expressed
as a percentage.
During the test, the pullback speed of the ultrasonic transducer assembly shall
be recorded.
Annex A
(informative)
Technical requirements for phantom and/or test piece
A.1 Phantom
A.1.1 Technical requirements for general phantom
During the tests in 5.2~5.16, the technical parameters of the phantom used for
testing are as follows:
Sound velocity of tissue-like materials: (1540±10)m/s (23°C±3°C);
Sound attenuation of tissue-like materials: (0.7±0.05)dB/(cm·MHz) (23°C±3°C);
Nylon target line diameter: (0.3±0.05) mm;
Target line position tolerance: ±0.1mm;
Distance between adjacent target lines in longitudinal linear target group: 10mm;
Distance between adjacent target lines in horizontal linear target group: 10mm
or 20mm.
The depth of the resolution target group shall be able to meet the test needs.
A.1.2 Technical requirements for slice thickness phantom
During the test in 5.7, the technical parameters of the phantom used for testing
are as follows:
Background sound velocity of tissue-like material: (1540±10)m/s(23°C±3°C);
Background sound attenuation of tissue-like materials:
(0.7±0.05)dB/(cm·MHz)( 23°C±3°C);
Scattering target layer thickness: no more than 0.4mm.
A.1.3 Technical requirements for phantom for volume measurement
During the test in 5.12, the technical parameters of the phantom used for testing
are as follows:
Sound velocity of background material: (1540±10)m/s (23°C±3°C);
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of YY/T 1676-2020 be delivered?Answer: The full copy PDF of English version of YY/T 1676-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of YY/T 1676-2020_English with my colleagues?Answer: Yes. The purchased PDF of YY/T 1676-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- YY/T 1676-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of YY/T 1676-2020?A step-by-step guide to download PDF of YY/T 1676-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "YY/T 1676-2020".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|