YD/T 2554.1-2013 (YD/T2554.1-2013, YDT 2554.1-2013, YDT2554.1-2013)
Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
YD/T 2554.1-2013 | English | 85 |
Add to Cart
|
0--9 seconds. Auto-delivery
|
Plastic optical fiber connector - Part 1: Type LC
| Valid |
YD/T 2554.1-2013
|
Preview PDF: YD/T 2554.1-2013
Standard ID | YD/T 2554.1-2013 (YD/T2554.1-2013) | Description (Translated English) | Plastic optical fiber connector - Part 1: Type LC | Sector / Industry | Telecommunication Industry Standard (Recommended) | Classification of Chinese Standard | M33 | Classification of International Standard | 30.180.20 | Word Count Estimation | 24,242 | Quoted Standard | GB/T 2828.1-2003; YD/T 1272.1-2003; YD/T 1272.3-2005; YD/T 1447-20XX; SJ/T 11363-2006; SJ/T 11364-2006; SJ/T 11365-2006 | Adopted Standard | IEC 61750-20-2012, NEQ | Drafting Organization | Pu Industrial Co., Ltd., Dongguan City, a | Administrative Organization | China Communications Standards Association | Regulation (derived from) | Ministry of Industry and Information Technology Bulletin No. 23 of 2013 | Summary | This standard specifies the terms and definitions LC-type plastic optical fiber connectors, technical requirements and test methods for measuring the quality assessment procedures, inspection rules and signs, packaging, transportation and storage requirem |
YD/T 2554.1-2013
YD
COMMUNICATION INDUSTRY STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
ICS 30.180.20
M 33
Plastic Optical Fiber Connector
Part 1. Type LC
塑料光纤活动连接器
ISSUED ON. APRIL 25, 2013
IMPLEMENTED ON. JUNE 1, 2013
Issued by. Ministry of Industry and Information Technology of the
People's Republic of China
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative References ... 4
3 Terms and Definitions ... 4
4 Technical Requirements ... 5
4.1 Classification ... 5
4.2 Interface diagrams and mating dimension ... 6
4.3 Materials ... 16
4.4 Standard Connector ... 16
4.5 Optical Performance of Type-LC Connector ... 16
4.6 Working Temperature of Type-LC Connector ... 17
4.7 Environmental Protection Conformance ... 17
5 Measurement and Testing ... 17
5.1 Appearance Inspection ... 17
5.2 Appearance Dimensions ... 17
5.3 Measurement and Testing Conditions ... 17
5.4 Measurement of Insertion Loss ... 18
5.5 Testing ... 19
6 Procedure of Quality Assessment ... 21
6.1 General ... 21
6.2 Qualification Approval Procedure ... 21
6.3 Quality Conformity Inspection ... 23
7 Inspection ... 26
7.1 Classification of Inspection ... 26
7.2 Exit-factory Inspection ... 26
7.3 Type Inspection ... 26
8 Marking, Packaging, Transport and Storage ... 27
8.1 Marking ... 27
8.2 Packaging ... 27
8.3 Transport ... 27
8.4 Storage ... 27
Foreword
“Plastic Optical Fiber Connector” is currently divided into the following parts.
- Part 1. Type LC;
- Part 2. Type SC;
- Part 3. Type FC.
This Part is Part 1 of “Plastic Optical Fiber Connector”.
This Part was drafted according to the rules given in GB/T 1.1-2009.
This Part was prepared by reference to IEC 61754-20-2012 “Fibre Optic Connector
Interfaces – Part 20. Type LC Connector Family”.
Please note that some of the contents of this document may involve patents. The
issuing organization of this document does not undertake the responsibility for
identifying any or all od these patents.
This Part was proposed by and shall be under the jurisdiction of China
Communications Standards Association.
Drafting organizations of this Part. Dongguan IPT Industrial Co., Ltd., Wuhan
Research Institute of Posts & Telecommunications, Zhongxing Telecommunication
Equipment Corporation, Inner Mongolia Golden Triangle Optical Fiber Technology Co.,
Ltd., Hebei Sifang Communication Equipment Co., Ltd.
Chief drafters of this Part. Cao Zhiwen, Liang Chenhuan, Wang Zihe, Hao Yanhui,
Zheng Yansheng, Ge Chao, Huang Xinge, Fang Sheng.
Plastic Optical Fiber Connector
Part 1. Type LC
1 Scope
This Part specifies the terms and definitions, technical requirements, measurement
and test methods, quality assessment procedure, inspection rules and marking,
packaging, transport and storage for the Type LC family of plastic optical fiber
connectors.
This Part is applicable to the Type LC plastic optical fiber connectors (hereinafter
referred to as "Type-LC connector").
2 Normative References
The following documents are indispensable for the application of this document. For
the dated references, only the edition cited applies. For the undated references, the
latest edition of the referenced document (including any amendments) applies.
GB/T 2828.1-2003 Sampling Procedures for Inspection by Attributes - Part 1.
Sampling Schemes Indexed by Acceptance Quality Limit
(AQL) for Lot-by-lot Inspection
YD/T 1272.1-2003 Optical Fiber Connector - Part 1. Type LC
YD/T 1272.3-2005 Optical Fiber Connector - Part 3. Type SC
YD/T 1447-20xx Plastic Optical Fiber for Communication
SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous
Substances in Electronic Information Products
SJ/T 11364-2006 Marking for Control of Pollution Caused by Electronic
Information Products
SJ/T 11365-2006 Testing Methods for Hazardous Substances in Electronic
Information Products
3 Terms and Definitions
For the purposes of this document, the terms and definitions defined in YD/T
1272.1-2003 AND the following one apply.
3.1
Type LC plastic optical fiber connector
Type LC connector that is made from plastic optical fiber for communication.
4 Technical Requirements
4.1 Classification
4.1.1 Plug interface
It may be divided into four types of interfaces according to the optical fiber cores and
plug-pin outer diameter.
a) φ1.250 plug-pin single-core plastic optical fiber plug interface;
b) φ1.250 plug-pin dual-core plastic optical fiber plug interface;
c) φ1.950 plug-pin single-core plastic optical fiber plug interface;
d) φ1.950 plug-pin dual-core plastic optical fiber plug interface.
4.1.2 Adaptor interface
It may be divided into 8 types of interfaces according to the optical fiber cores and
application.
a) φ1.250 sheath single-core plastic optical fiber connector adapter;
b) φ1.250 sheath single-core plastic optical fiber connector active-device
receptacle interface;
c) φ1.250 sheath dual-core plastic optical fiber connector adapter;
d) φ1.250 sheath dual-core plastic optical fiber connector active-device
receptacle interface;
e) φ1.950 sheath single-core plastic optical fiber connector adapter;
f) φ1.950 sheath single-core plastic optical fiber connector active-device
receptacle interface;
g) φ1.950 sheath dual-core plastic optical fiber connector adapter;
h) φ1.950 sheath dual-core plastic optical fiber connector active-device
receptacle interface.
Table 4 Mating dimensions of Single-core and Dual-core Active-device Receptacle Interfaces
Mark Unit Minimum Maximum Notes
Aa,b mm - - Inner diameter of alignment-device, see Table 5
B mm 9.9 10.0
C mm 4.5 -
D mm 3.4 3.5
E mm 2.6 2.7
F mm 0.2 0.3 Radius of curvature
G mm 4.0 4.1
H1c mm 4.60 4.75
H2c mm 4.60 4.75
I mm 2.87 2.97 Diameter
J mm 2.29 Basic dimension
Kd mm 6.25 Basic dimension
Lc ° - 0.2
M mm 1.0 1.1
N mm 0.5 0.6
O mm - 1.3
P ° 15 Typical value
AO mm 11.0 12.8
AP mm 14.5 14.7
AQ mm 2.2 2.4 Diameter
AR mm 1.1 1.2
AS mm 6.6 6.8
AT mm 0.6 0.7
AV mm 1.0 1.1
AW mm 0.5 0.6 Grade, see Table 5
AX mm 1.9 -
a The connector alignment-device is a rigid bore sheath or resilient alignment sheath. Dimension A defines the
inner diameter of the alignment-device.
b The sheath may be fixed or floating. For a fixed sheath, the positional tolerance applies. For a floating sheath,
a pin-gauge inserted in the sheath must be capable of moving freely into a position such that it is coincident
with datum B.
c Taper (oblique), dimension L, is applied to the surfaces associated with dimensions/features H1 and H2.
d Each of the units in the dual-core active-device receptacle shall comply with all dimensions of Figure 6,
except the added dimension K, distance between dual-core active-device receptacles.
4.2.6 Alignment sheath grade of adapter and active-device receptacle
See Table 5 for the classification of adapter and active-device receptacle interfaces
(i.e. alignment sheath grade).
4.3 Materials
Plastic optical fibers, as specified in Y...
......
|