GB/T 6556-2016 (GB/T6556-2016, GBT 6556-2016, GBT6556-2016)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 6556-2016 | English | 85 |
Add to Cart
|
0--9 seconds. Auto-delivery
|
Type, main dimension, material and marking of mechanical seals
| Valid |
GB/T 6556-2016
|
Standards related to: GB/T 6556-2016
| Standard ID | GB/T 6556-2016 (GB/T6556-2016) | | Description (Translated English) | Type, main dimension, material and marking of mechanical seals | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J22 | | Classification of International Standard | 21.140 | | Word Count Estimation | 10,150 | | Date of Issue | 1986-08-04 | | Date of Implementation | 2017-03-01 | | Older Standard (superseded by this standard) | GB/T 6556-1994 | | Drafting Organization | Hefei General Machinery Research Institute, Hefei General Environmental Control Technology Co., Ltd., Sichuan University, Beijing University of Chemical Technology, Jiangsu Huaqing Fluid Technology Co., Ltd. | | Administrative Organization | National Standardization Technical Committee for Mechanical Seals (SAC/TC 491) | | Regulation (derived from) | National Standard Announcement 2016 No.14 | | Proposing organization | China Machinery Industry Federation | | Issuing agency(ies) | General Administration of Quality Supervision, Inspection and Quarantine of the People Republic of China, Standardization Administration of the People Republic of China | GB/T 6556-2016
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 21.140
J 22
Replacing GB/T 6556-1994
Type, Main Dimension, Material
and Marking of Mechanical Seals
ISSUED ON. AUGUST 29, 2016
IMPLEMENTED ON. MARCH 1, 2017
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine of the People's Republic of China;
Standardization Administration of the People's Republic of
China.
3. No action is required - Full-copy of this standard will be automatically &
immediately delivered to your EMAIL address in 0~60 minutes.
Table of Contents
Foreword ... 3
1 Application Scope ... 4
2 Normative References ... 4
3 Type and Main Dimension ... 4
4 Marking ... 10
5 Material Code ... 11
Foreword
This Standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This Standard replaces GB/T 6556-1994, Type, Main Dimension, Material and Marking
of Mechanical Seals. Compared with GB/T 6556-1994, the major changes are as
follows, in addition to editorial changes.
-- it adds BU double mechanical seal type;
-- it adjusts the marking of mechanical seal.
This Standard was proposed by China Iron and Steel Association.
This Standard shall be under the jurisdiction of the National Standardization Technical
Committee on Mechanical Seals (SAC/TC 183).
The main drafting organizations of this Standard. Hefei General Machinery Research
Institute, Hefei General Environment Control Technology Co., Ltd., Sichuan University,
Beijing University of Chemical Technology, Jiangsu Huaqing Fluid Technology Co., Ltd.
The main drafters of this Standard. Wu Zhaoshan, Li Xiang, Chen Zhi, Shen Zongzhao,
Ding Siyun, Li Fengcheng, Wen Lan, Li Jihe, Li Kun.
The previous edition of the standard replaced by this Standard is as follows.
-- GB/T 6556-1994.
Type, Main Dimension, Material
and Marking of Mechanical Seals
1 Application Scope
This Standard specifies the type, main dimension, marking and material code of
mechanical seals for centrifugal pumps and similar rotary machines.
This Standard applies to single and double mechanical seals.
2 Normative References
The following referenced documents are indispensable for the application of this
document. For dated references, only the edition dated applies to this document. For
undated references, the latest edition of the referenced documents (including all
amendments) applies to this Standard.
GB/T 1804-2000, General Tolerances – Tolerances for Linear and Angular
Dimensions Without Individual Tolerance Indications
GB/T 10444, Method of Type Establishment for Mechanical Seals
3 Type and Main Dimension
3.1 General requirements
All types of mechanical seals may be of the structures shown in Figure 1 ~ Figure 6,
but the dimensions given shall be followed. The figures give the examples in which O
ring is used as stationary auxiliary seal ring; the seal rings of other sectional types may
also work as stationary auxiliary seal ring. The dimensional tolerances not specified
shall be as specified in GB/T 1804-2000, grade f.
3.2 Single mechanical seal type
U type. unbalanced single mechanical seal. See Figure 1.
B type. balanced single mechanical seal. See Figure 2.
4 Marking
4.1 Marking of single mechanical seals
The marking of single mechanical seals is as follows.
EXAMPLE. 108-0-N-R-055-QBPFF indicates type 108 single mechanical seals of.
non-cartridge type seal (0), design type N, right rotation (R), nominal diameter d1 55
mm (055), rotary ring material silicon nitride (Q), stationary ring material graphite
impregnating resin (B), auxiliary seal ring material nitrile rubber buna (P), spring
material chrome-nickel steel (F) and other structural members’ material chrome-nickel
steel (F).
4.2 Marking of double mechanical seals
The marking of double mechanical seals is as follows.
EXAMPLE. UB191-0-080-UAVFF/UBPFF indicates UB191 double mechanical seals
of. unbalanced medium side (U), balanced atmospheric side (B), non-cartridge seal
(O), nominal diameter 80 mm (080), medium side materials including rotary ring
material Co base tungsten carbide (U), stationary ring material graphite impregnating
metal (A) and auxiliary seal ring material fluororubber (V), spring material chrome-
nickel steel (F) and other structural members’ material chrome-nickel steel (F),
atmospheric side materials including rotary ring material Co base tungsten carbide (U),
stationary ring material graphite impregnating resin (B), auxiliary seal ring material
Material code (see 5.1)
Nominal diameter of mechanical seals, expressed with 3 digits; add
“0” in front if less than 3 digits
Direction of rotation (R for right, L for left and S for any direction)
Type of mechanical seal design (N, K)
1 for cartridge seals, 0 for non-cartridge seals (o can be omitted)
Type of mechanical seal (as specified in GB/T 10444)
Material code (see 5.1)
Nominal diameter of mechanical seals, expressed with 3 digits; add
“0” in front if less than 3 digits
1 for cartridge seals, 0 for non-cartridge seals (o can be omitted)
Mechanical seal type number (as specified in GB/T 10444)
...
|