HOME   Cart(0)   Quotation   About-Us Tax PDFs Standard-List Powered by Google www.ChineseStandard.net Database: 189760 (7 Dec 2024)

GB/T 42611-2023 English PDF

GB/T 42611-2023 (GB/T42611-2023, GBT 42611-2023, GBT42611-2023)
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)StatusPDF
GB/T 42611-2023English185 Add to Cart 0--9 seconds. Auto-delivery Test method for sightseeing vehicle brake performance Valid GB/T 42611-2023
Preview PDF: GB/T 42611-2023

BASIC DATA
Standard ID GB/T 42611-2023 (GB/T42611-2023)
Description (Translated English) Test method for sightseeing vehicle brake performance
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard Y57
Classification of International Standard 97.200.40
Word Count Estimation 10,181
Date of Issue 2023-05-23
Date of Implementation 2023-09-01
Drafting Organization China Machinery Technology (Beijing) Vehicle Testing Engineering Research Institute Co., Ltd., Guangdong Lvtong New Energy Electric Vehicle Technology Co., Ltd., Liuzhou Wuling Automobile Industry Co., Ltd., China Special Equipment Inspection and Research Institute, China National Accreditation Center for Conformity Assessment, Qinghai Special Equipment Inspection and Testing Institute, Yichang Xinwei Special Vehicle Manufacturing Co., Ltd.
Administrative Organization National Cableway and Amusement Facilities Standardization Technical Committee (SAC/TC 250)
Proposing organization National Cableway and Amusement Facilities Standardization Technical Committee (SAC/TC 250)
Issuing agency(ies) State Administration for Market Regulation, National Standardization Management Committee


GB/T 42611-2023 GB NATIONAL STANDARD OF THE PEOPLE'S REPUBLIC OF CHINA ICS 97.200.40 CCS Y 57 Test method for sightseeing vehicle brake performance ISSUED ON: MAY 23, 2023 IMPLEMENTED ON: SEPTEMBER 1, 2023 Issued by: State Administration for Market Regulation; Standardization Administration of PRC. Table of Contents Foreword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 4 4 Technical requirements ... 5 4.1 General requirements for sightseeing vehicles ... 5 4.2 Special requirements for sightseeing combination buses ... 7 5 Test methods ... 8 5.1 Preparation before the test ... 8 5.2 Visual inspection ... 8 5.3 Service braking test ... 9 5.4 Strength test for the service braking system ... 9 5.5 Parking braking test on ramps ... 10 5.6 Braking heat fade test for garden patrol minibuses ... 10 5.7 Braking heat fade test for sightseeing combination buses ... 10 5.8 Braking heat fade recovery test ... 10 5.9 Speed limiting braking test for garden patrol minibuses ... 10 5.10 Air pressure test for sightseeing combination bus braking system ... 11 5.11 Braking test after the carriage of the sightseeing combination bus is disconnected ... 11 References ... 13 Test method for sightseeing vehicle brake performance 1 Scope This document specifies the technical requirements and test methods for the braking performance of sightseeing vehicles. This document is applicable to the braking performance test of sightseeing vehicles (including garden patrol minibuses and sightseeing combination buses, hereinafter referred to as "sightseeing vehicles"). 2 Normative references The following documents contain the provisions which, through normative reference in this document, constitute the essential provisions of this document. For the dated referenced documents, only the versions with the indicated dates are applicable to this document; for the undated referenced documents, only the latest version (including all the amendments) is applicable to this document. GB/T 21268 General technical conditions for garden patrol minibus GB/T 38433 General technical specifications for sightseeing combination bus 3 Terms and definitions The terms and definitions defined in GB/T 21268 and GB/T 38433 and the following apply to this document. 3.1 braking distance The distance traveled from the moment the driver starts to activate the brake control device to the moment the sightseeing vehicle stops, when the sightseeing vehicle travels at a specific initial speed. 3.2 service braking system The braking system by which the driver can directly or indirectly control the sightseeing vehicle to slow down or stop the sightseeing vehicle. 3.3 parking braking system On permitted ramps or level roads, the braking system that uses a mechanical mechanism to keep the sightseeing vehicle stationary, while the driver does not need to continuously operate the control device. 3.4 braking device A mechanism or device that slows, stops a vehicle's wheels, or holds a vehicle's wheels in a stopped state. NOTE: Generally it refers to the actuating components of the braking system and its ancillary devices. 3.5 braking heat fade Multiple braking operations or driving with the braking device in an incompletely combined state cause the braking device temperature to rise, resulting in a decline in the braking performance of the sightseeing vehicle. 3.6 braking stability During the braking process, the ability of the sightseeing vehicle to maintain straight driving without adjusting the steering wheel, which is reflected in the fact that any part of the vehicle (except for parts not included in the width of the vehicle) during the braking process does not exceed the specified test channel width. 3.7 electronic parking device The device in which the holding mechanism is activated by an electronic switch button, and the electronic control unit and actuator work together to realize the parking braking. NOTE: This device is a parking brake device controlled by an electronic system. 4 Technical requirements 4.1 General requirements for sightseeing vehicles 4.1.1 The pedal, handle, or electronic parking devices that implement service braking and parking braking shall be convenient for the driver to operate. Sightseeing vehicles shall have a complete service braking system and parking braking system that are sufficient to decelerate, stop, and park the vehicle. The service braking function shall act on all wheels of the sightseeing vehicle. The control device of the service braking and the control device of the parking braking system shall be independent of each other. 4.1.2 The service braking distance and braking stability shall meet the requirements of Table 1, and the brake pedal force shall not be greater than 700 N. 4.1.8 The service braking pedal or handle shall be arranged according to the operating habits of the right foot or right hand. 4.1.9 The service braking system shall not affect the function of the service braking due to corrosion of the brake pipeline by the brake fluid or air resistance caused by the action of the engine and other heat sources. 4.1.10 Garden patrol minibuses shall be equipped with brake lights at the rear of the car; sightseeing combination buses shall be equipped with brake lights in the last carriage. The brake lights are triggered when the driver steps on the brake pedal. 4.1.11 Garden patrol minibuses with a speed limit function, when the specified speed limit is reached, will automatically decelerate the vehicle through the retarder, motor speed limit, or automatic start of the service braking system. The deceleration speed is adjustable and the vehicle speed can be limited to within 110% of the design parameter value. 4.2 Special requirements for sightseeing combination buses 4.2.1 For sightseeing combination buses that use air pressure braking, when the air pressure of the braking system is lower than the starting air pressure, the alarm device shall be able to continuously send an audible or visible alarm signal to the driver. 4.2.2 The braking system of each carriage shall have an independent air reservoir. The capacity of the air reservoir shall ensure that under the condition of rated working pressure and no further inflation, after five consecutive maximum braking travels of the sightseeing combination bus, the pressure in the air reservoir can still remain no lower than the starting air pressure. 4.2.3 The air pressure braking system of sightseeing combination buses shall be equipped with a pressure limiting device to ensure that the air pressure in the air reservoir does not exceed the maximum allowable air pressure. The air pressure braking system shall be equipped with a device to keep the compressed air dry and separate oil and water. After the braking air pressure reaches the rated working pressure, turn off the power of the vehicle and keep it stationary for 2 hours; there shall be no obvious air loss. After starting the sightseeing combination bus, press the brake pedal for five consecutive times full travel; during this period, the braking system shall not alarm, and the brake charging pump shall not start. 4.2.4 When the carriage is suddenly decoupled and separated while the sightseeing combination bus is running, causing the braking pipe or braking signal line to break, the carriage braking system shall brake immediately and enable the decoupled carriage to brake and stop within 8m. The braking process shall not cause harm to passengers. After the carriage stops, the parking state shall be easily released. If special tools are needed, they shall be equipped with the vehicle. 4.2.5 When the sightseeing combination bus is braked, the danger caused by the collision of carriages and the discomfort to passengers shall be avoided. 5 Test methods 5.1 Preparation before the test 5.1.1 All assemblies, components, accessories, and ancillary devices of the prototype are fully equipped and fully running as required, so that they are in normal technical condition. The battery voltage is sufficient, the oil and fluids meet the ex-factory conditions, all mechanical transmissions are well lubricated, the braking system functions normally, and the tire pressure meets the specifications in the manual. 5.1.2 The environmental conditions during the test shall meet the following requirements: a) Temperature is at -5 ℃~40 ℃; b) The wind speed does not exceed 3 m/s; c) The relative humidity of the air is not greater than 90%; d) The altitude is less than 2000 m. 5.1.3 The test site shall be a dry, flat concrete or asphalt pavement, and the length and width shall meet the test requirements. 5.1.4 The instruments, equipment, and measuring tools used in the test shall be verified or calibrated and used within the validity period. 5.1.5 The unloaded and fully loaded state of the sightseeing vehicle during the test shall meet the requirements of GB/T 21268 and GB/T 38433. 5.2 Visual inspection Check whether the braking system of the sightseeing vehicle complies with the provisions of 4.1.1, 4.1.3, 4.1.6, 4.1.8, 4.1.9, 4.1.10, 4.2.1, and 4.2.3 through visual inspection and functional verification. 5.5 Parking braking test on ramps The sightseeing vehicle is fully loaded and parked on the ramp specified in 4.1.5. The transmission is in neutral (if any), the engine is turned off or the running motor is turned off, and the parking braking control device is operated to park the vehicle on the ramp. Measure the braking force and the sliding distance of the vehicle within 10 minutes. Carry out the upslope and downslope tests once each to check whether the test results comply with the provisions of 4.1.5. 5.6 Braking heat fade test for garden patrol minibuses When the ambient temperature is no less than 15°C and the garden patrol minibus is fully loaded, after pressing the accelerator pedal to bring the vehicle to the maximum speed, keep the accelerator pedal at the maximum stroke, and then slowly press the brake pedal to bring the vehicle speed to 40%~50% of its maximum speed, continue operating for 2 km, causing the braking device to heat up. Then perform the braking distance test again according to the provisions of 5.3. Check whether the test results comply with the provisions of 4.1.7. NOTE: This item is not applicable to vehicles with active retarding protection functions. 5.7 Braking heat fade test for sightseeing combination buses When the sightseeing combination bus is fully loaded, after five consecutive emergency braking tests according to the test method specified in 5.3, immediately measure the braking distance for one round travel, record the braking distance, and take the average value. Check whether the test results comply with the provisions of 4.1.7. 5.8 Braking heat fade recovery test After the sightseeing vehicle has been tested for braking heat fade, wait for the brake temperature to return to the ambient temperature or wait for 1 hour, and then conduct the braking distance test according to the provisions of 5.3. Check whether the test results comply with the provisions of 4.1.2. 5.9 Speed limiting braking test for garden patrol minibuses Place the garden patrol minibus on the chassis dynamometer in an unloaded state, slowly press the accelerator pedal, and keep the accelerator pedal at the extreme position. After the operation is stable, increase the torque of the rotating hub where the drive wheel is located to give the garden patrol minibus a forward thrust until the forward thrust reaches the value specified in formula (2). Run for 5 minutes, record the vehicle speed within 5 minutes, and check whether the test results comply with the provisions of 4.1.11. where: F -- the forward thrust given by the rotating hub to the garden patrol minibus, in kilonewtons (kN); G -- the unloaded weight of the garden patrol minibus, in kilonewtons (kN); T -- the unloaded rolling resistance of the garden patrol minibus, in kilonewtons (kN); 0.342 -- the downward component coefficient of the weight of the garden patrol minibus on a 20° ramp. NOTE 1: On a flat test road surface, when the garden patrol minibus under test is unloaded and the brake is not activated, connect the test auxiliary vehicle to the garden patrol minibus, and connect the tension sensor in series in the middle. Start the auxiliary vehicle and slowly pull the minibus under test. When the minibus runs smoothly, record the traction data, which is the rolling resistance of the minibus. NOTE 2: This test is not performed on sightseeing combination buses. 5.10 Air pressure test for sightseeing combination bus braking system Start the sightseeing combination bus, make the braking air pressure reach the rated working pressure, turn off the vehicle, and wait for 2 hours to observe whether there is obvious air leakage; after starting the sightseeing combination bus, press the brake pedal full travel for five consecutive times, during this period, observe whether the braking system is giving an alarm, the brake charging pump is activated. Check whether the test results comply with the provisions of 4.2.3. 5.11 Braking test after the carriage of the sightseeing combination bus is disconnected Before the test, it shall be checked to confirm whether the braking structure of the carriage under test is normally closed and there are no abnormalities. Use a forklift or other handling equipment to place or pull a carriage onto a ramp with a specified design gradient; at this time, the carriage is in a braking state. Use a vehicle- mounted or external air pump to pressurize the braking device (if it is an electric braking ......