GB/T 33165-2016 PDF English
US$90.00 · In stock · Download in 9 secondsGB/T 33165-2016: Quantitative Analysis Method of Centre Segregation for High Carbon Steel Wire Rod Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 33165-2016 | English | 90 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Quantitative Analysis Method of Centre Segregation for High Carbon Steel Wire Rod
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 33165-2016
GB/T 33165-2016: Quantitative Analysis Method of Centre Segregation for High Carbon Steel Wire Rod
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT33165-2016
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.040.99
H 24
Quantitative Analysis Method of Centre
Segregation for High Carbon Steel Wire Rod
Issued on: OCTOBER 13, 2016
Implemented on: SEPTEMBER 1, 2017
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative References ... 4
3 Terms and Definitions ... 4
4 Method Principle ... 5
5 Instrument and Auxiliary Equipment ... 6
6 Standard Sample ... 6
7 Specimen Preparation ... 6
8 Measuring Conditions ... 7
9 Working Curve ... 7
10 Specimen Line Analysis ... 7
11 Measuring Results ... 8
12 Uncertainty of Measuring Results ... 10
13 Test Report ... 10
Appendix A (Informative) Working Curve Setting Example ... 11
Appendix B (Informative) Factors Affecting the Measuring Uncertainty of the
Element Content by Spectrometer ... 13
Foreword
This Standard was drafted as per the rules specified in GB/T 1.1-2009.
This Standard was proposed by China Iron and Steel Industry Association.
This Standard shall be under the jurisdiction of National Technical Committee for
Standardization of Steel (SAC/TC 183).
Drafting organizations of this Standard. Wuhan Iron and Steel Co., Ltd., China
Metallurgical Information and Standardization Institute, and Tianjin Iron and Steel
(Group) Co., Ltd.
Chief drafting staffs of this Standard. Sun Yiqiang, Wu Lixin, Wang Zhifen, Chen
Shihua, Yan Chengming, Han Rongdong, Deng Zhaojun, Zhang Long, and Luo
Chunmin.
Quantitative Analysis Method of Centre
Segregation for High Carbon Steel Wire Rod
1 Scope
This Standard specifies the terms, principle, instrument and auxiliary equipment,
standard sample, specimen preparation, measuring conditions and methods, and
result analysis for quantitative analysis of center segregation for high carbon steel wire
rod by using spectrometer.
This Standard is applicable to the high carbons steel hot-rolled wire rod with carbon
content greater than 0.65%.
2 Normative References
The following documents are essential to the application of this document. For the
dated documents, only the versions with the dates indicated are applicable to this
document; for the undated documents, only the latest version (including all the
amendments) are applicable to this document.
GB/T 4930 Microbeam Analysis - Electron Probe Microanalysis - Guidelines for
the Specification of Certified Reference Materials (Crms)
GB/T 13298 Inspection Methods of Microstructure for Metals
GB/T 15074 General Guide of Quantitative Analysis by EPMA
GB/T 21636 Microbeam Analysis - Electron Probe Micro Analysis (EPMA) -
Vocabulary
GB/T 27025 General Requirements for the Competence of Testing and Calibration
Laboratories
GB/T 30067 Standard Terminology Relating to Metallography
3 Terms and Definitions
The following terms and definitions and those stipulated in GB/T 21636 and GB/T
30067 are applicable to this document.
5 Instrument and Auxiliary Equipment
The testing laboratory shall meet the requirements of GB/T 27025; and have the
following instrument and auxiliary equipment.
a) Electron probe analyzer or scanning electron microscope for installing
spectrometer accessories.
b) Metallographic specimen preparation device, including specimen embedding,
grinding, polishing and corrosion device.
c) Metallographic microscope.
d) Ultrasonic cleaning device.
6 Standard Sample
6.1 Selection of standard sample
It is recommended to use the carbon element standard sample that conforms to the
provisions of GB/T 4930; the number of standard sample shall be no less than 3; the
carbon element content range in standard sample shall cover the carbon element
content of the specimen.
6.2 Treatment of standard sample
The standard sample needs re-polishing before use; check the surface by the
metallographic microscope to confirm whether there is contamination or other defects
that affect the measurement. The surface of standard sample shall not spray or coat
the covering layer, the standard sample shall be grounding by adopting conductive
double-side adhesive, conductive copper foil tape or liquid silver glue sample
connecting stage.
7 Specimen Preparation
Take the cross-section of wire rod as the specimen, then make the metallographic
polishing specimen as per GB/T 13298. After acid leaching the specimen into 2%~4%
nitric acid alcohol solution, use glass knife, scalpel or other sharp tools to make parallel
scratch mark on two sides of the segregation area, the scratch is approximately
tangent to the edge of segregation area (see Figure 1). Through polishing again, the
corrosion layer is completely removed from the specimen, while the scratch mark is
retained.
Appendix B
(Informative)
Factors Affecting the
Measuring Uncertainty of the
Element Content by Spectrometer
B.1 Sample contamination. including the water stains on the polishing surface, dust,
and other contaminants.
B.2 Sample electric charge accumulation. mainly caused by not grounding, poor
grounding of the sample; or too high current and voltage.
B.3 Measurement repeatability. including the fluctuation of measuring valued caused
by the fluctuation of accelerated voltage, beam, and detector.
B.4 Working curve. the linearity of working curve affects the measuring results.
B.5 Standard sample. the uncertainty and nonuniformity of element content in
standard sample affect the measuring results.
B.6 Rounding off on the measuring results. the rounding off on measuring value
affects the measuring results.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 33165-2016 be delivered?Answer: The full copy PDF of English version of GB/T 33165-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 33165-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 33165-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 33165-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 33165-2016?A step-by-step guide to download PDF of GB/T 33165-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 33165-2016".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|